Description
Low-Density Lipoprotein (LDL) in plasma is the main carrier of endogenous cholesterol. It is degraded and metabolized by binding to the LDL receptor (LDL-R) on cell membranes and serves as the primary vehicle for transporting cholesterol to peripheral tissues. However, when LDL, especially oxidized LDL (OX-LDL), is present in excess, the cholesterol it carries accumulates in the arterial walls, increasing the risk of atherosclerosis. Atherosclerosis is the pathological basis and risk factor for the majority of cardiovascular and cerebrovascular diseases.Detection Principle: In a cholesterol assay system containing cholesterol esterase (CHER) and cholesterol oxidase (CHOD), specific surfactants are added to selectively solubilize LDL-C for the determination of LDL-cholesterol. Other lipoproteins (HDL, VLDL, chylomicrons) do not react due to inhibition by the surfactants and sugar compounds, remaining in the form of lipoproteins in the reaction mixture. Based on this principle, LDL-cholesterol can be measured directly. Subsequently, esterase catalyzes the hydrolysis of cholesterol esters to generate Free Cholesterol (FC). FC is oxidized by cholesterol oxidase to produce 4-cholestenone and hydrogen peroxide. Hydrogen peroxide then reacts with 4-aminoantipyrine and other components to produce a red quinoneimine compound, which has a characteristic absorption peak at 546 nm. The LDL-C content is determined by measuring the absorbance at 546 nm.Component96TStorageReagent 118 mL2-8℃. Store in the dark.Reagent 26 mL2-8℃. Store in the dark.Standard1EA2-8℃. Store in the dark.Standard (Powder, 1 vial) Preparation:1. Before use, centrifuge at 8000 g, 4°C for 2 minutes to collect the powder at the bottom of the tube.2. Add 0.1 mL of distilled water to dissolve. Use within one week. The prepared concentration is as indicated on the label.User-Prepared Instruments and Reagents:Mortar (Homogenizer), balance, ice box (ice maker), benchtop centrifuge, adjustable micropipettes, water bath (oven, incubator, metal bath), 96-well plate, centrifuge tubes, microplate reader, distilled water (deionized water or ultrapure water are acceptable), ethanol.Experimental ProcedureIt is recommended to first perform a preliminary test using 1-3 samples with expected significant differences (e.g., different types or groups) to familiarize yourself with the procedure and to determine or adjust sample concentrations based on the preliminary results, preventing unnecessary waste of samples or reagents.1. Sample Extraction1.1 Tissue SamplesWeigh approximately 0.1 g of tissue sample and place it in a mortar. Add 1 mL of ethanol and homogenize in an ice bath. Centrifuge at 12,000 rpm, 4°C or room temperature for 10 minutes. Collect the supernatant for assay.Note: If increasing the sample amount, maintain a tissue mass (g) to ethanol volume (mL) ratio between 1:5 and 1:10.1.2 Liquid SamplesAssay clear liquid samples directly. If turbid, centrifuge and use the supernatant for assay.1.3 Bacterial/Cell SamplesCollect bacteria or cells into a centrifuge tube, centrifuge, and discard the supernatant. Add 1 mL of ethanol per approximately 5 million bacteria/cells. Disrupt the bacteria or cells by sonication in an ice bath (power 200W, pulse 3s on, 10s off, repeat 30 times). Centrifuge at 12,000 rpm, 4°C for 10 minutes. Collect the supernatant and keep it on ice for assay.*Note: If increasing the sample amount, maintain a bacteria/cell count (10⁴) to ethanol volume (mL) ratio between 500:1 and 1000:1.*2. Assay Steps2.1 Preheat the microplate reader for 30 minutes (or wait for the instrument to complete its self-check). Set the wavelength to 546 nm.2.2 Thaw all reagents to room temperature (25°C). Add reagents sequentially to a 96-well plate as follows:Reagent (µL)Test TubeStandard Tube (once)Blank Tube (once)Sample2.5Standard2.5Distilled Water2.5Reagent 1180180180Mix well and incubate at 37°C for 5 minutes. Read the absorbance at 546 nm for each tube (A1 ).Reagent 2606060Mix well and incubate at 37°C for 10 minutes. Read the absorbance at 546 nm for each tube (A2 ). Calculate ΔA = A2 - A1 for each tube.Note:(1) If the A2 value for the Test Tube is greater than 1, dilute the sample with ethanol. The dilution factor (D) must be substituted into the calculation formula.(2) If ΔA for the Test Tube is lower than ΔA for the Blank Tube, consider increasing the sample volume V1 (e.g., increase the sample volume in the Test Tube and the water volume in the Blank Tube to 5 µL or more, keeping Reagents 1 and 2 volumes unchanged; for the Standard Tube, keep at 2.5 µL and add 2.5 µL distilled water to make up volume) or increasing the sample weight W (e.g., to 0.2 g or more). The changed V1 or W must then be substituted into the calculation formula.3. Calculation of Results3.1 Based on Sample MassDerived Formula:LDL-C (µmol/g weight) = (CStandard × V2 ) × (ΔATest - ΔABlank ) ÷ (ΔAStandard - ΔABlank ) ÷ (W × V1 ÷ V) × DSimplified Formula:LDL-C (µmol/g weight) = CStandard × (ΔATest - ΔABlank ) ÷ (ΔAStandard - ΔABlank ) ÷ W × D3.2 Based on Protein ContentDerived Formula:LDL-C (µmol/mg prot) = (CStandard × V2 ) × (ΔATest - ΔABlank ) ÷ (ΔAStandard - ΔABlank ) ÷ (Cpr × V1 ÷ V) × DSimplified Formula:LDL-C (µmol/mg prot) = CStandard × (ΔATest - ΔABlank ) ÷ (ΔAStandard - ΔABlank ) ÷ Cpr × D3.3 LDL-C Content in LiquidsDerived Formula:LDL-C (mmol/L) = (CStandard × V2 ) × (ΔATest - ΔABlank ) ÷ (ΔAStandard - ΔABlank ) ÷ V1 × DSimplified Formula:LDL-C (mmol/L) = CStandard × (ΔATest - ΔABlank ) ÷ (ΔAStandard - ΔABlank ) × D3.4 Based on Cell CountDerived Formula:LDL-C (nmol/10⁴ cells) = (CStandard × V2 ) × 10³ × (ΔATest - ΔABlank ) ÷ (ΔAStandard - ΔABlank ) ÷ (500 × V1 ÷ V) × DSimplified Formula:LDL-C (nmol/10⁴ cells) = 2 × CStandard × (ΔATest - ΔABlank ) ÷ (ΔAStandard - ΔABlank ) × DParameter Definitions:CStandard : Concentration as indicated on the label (mmol/L or µmol/mL)V1 : Volume of sample added (0.0025 mL)V: Volume of extraction buffer (ethanol) added (1 mL)V2 : Volume of standard added (0.0025 mL)D: Dilution factor (1 if not diluted)500: Number of cells (in units of 10⁴)W: Sample weight (g)Cpr: Protein concentration of the supernatant (mg/mL); Aladdin's BCA Protein Quantification Kit (B665595) or Ready-to-Use BCA Protein Quantification Kit (R1491648) is recommended.Precautions1. It is recommended to first perform a preliminary test using 1-3 samples with expected significant differences (e.g., different types or groups) to familiarize yourself with the procedure. Based on the preliminary results, determine or adjust sample concentrations to prevent unnecessary waste of samples or reagents.2. This product is for research use only. Not for use in clinical diagnosis. For your safety and health, please wear a lab coat and disposable gloves during operation