Description
Product Introduction:At present, the conventional proteome sample pretreatment process has many problems, such as poor reproducibility, poor method stability, low sensitivity, being very time-consuming, and inability to be automated. To address the above issues, Aladdin has launched a new generation of "All In One Tube" innovative products. This product is mainly designed for the processing of trace proteins (5-100µg). Even researchers without omics background can quickly prepare pretreated samples, which can be used for subsequent mass spectrometry analysis.Experimental Flowchart of Proteomics Pretreatment Kit (P1456469)Product Components and Storage Conditions:P1456469Component12 T24T48TStorageP1456469ALysis Buffer1.25 mL2.5 mL5 mL-20℃. Store in the dark.P1456469BDigest0.05 mL0.1 mL0.2 mL-20℃P1456469CBalance Buffer3 mL6 mL12 mL2-8℃P1456469DStop Buffer0.375 mL0.75 mL1.5 mLRTP1456469EWash Buffer I5 mL10 mL20 mLRTP1456469FWash Buffer II3.75 mL7.5 mL15 mLRTP1456469GWash Buffer III3.75 mL7.5 mL15 mLRTP1456469HElution Buffer6.25 mL12.5 mL25 mLRT. Store in the dark.P1456469ILoading Buffer0.25 mL0.5 mL1 mLRTP1456469JTip pillar12 T24T48TRTTrace proteins: Designed for the pretreatment of 5-100µg proteins.Simple operation: Enables rapid preparation of pretreated samples, requiring only a metal bath and a conventional centrifuge.High stability: Strict quality inspection for each batch ensures high reproducibility of experimental results.Operating Procedure:Lysis① Add 50µL of Lysis buffer to the EP tube containing the sample and mix by shaking.② Place the EP tube with Lysis buffer in a 95°C water bath for 10 minutes, then take it out and cool to room temperature.Enzymatic Digestion① Add 225µL of Balance buffer to the EP tube that has cooled to room temperature.② Add 3µL of Digest, mix well, and perform enzymatic digestion with shaking at 37°C and 1200rpm overnight (16 hours is recommended).Desalting (at room temperature)① Add 25µL of Stop buffer to the sample and vortex to mix.② Add 320µL of Wash buffer 1, shake vigorously for 3 minutes, centrifuge at 15000rpm for 3 minutes, and remove the supernatant.③ Transfer the lower layer sample into the Tip column, centrifuge at 2500rpm for 3-5 minutes until all liquid is centrifuged down. If the liquid flow rate is slow, the speed can be increased.④ Add 200µL of Wash buffer 2 (shake for 10-20 seconds before use) to the desalting column, centrifuge at 2500rpm for 3-5 minutes until all liquid is centrifuged down.⑤ Add 200µL of Wash buffer 3 to the desalting column, centrifuge at 2500rpm for 3-5 minutes until all liquid is centrifuged down.⑥ Put the desalting column into a new EP tube, add 200µL of Elution buffer to the desalting column, centrifuge at 2000rpm for 3-5 minutes until all liquid is centrifuged down.⑦ Repeat step ⑥, collect the eluates from both times, and freeze-dry them.⑧ Add 10µL of Loading buffer, vortex vigorously for 3 minutes, centrifuge at 20000g for 10 minutes, take an appropriate amount of sample, and then mass spectrometry detection can be performed. Taking the HF-X instrument as an example, 0.5-1µg of sample is sufficient for loading.Precautions:After aliquoting, Digest should be stored at -20°C.After aliquoting, Lysis Buffer should be stored at -20°C and avoid repeated freezing and thawing.This product is limited to scientific research use by professionals, and must not be used for clinical diagnosis or treatment, nor for food or drugs