| Description | The content of this cell is too long for an XLSX file (more than 32767 characters). Please use the CSV format for this export | Inquire | Product introduction：Product introduction：Cell Cycle Assay Kit Plus ( Cell Cycle Assay Kit Plus ) has certain applicability for live cells and fixed cell cycle detection. For different types of cells, whether it is applicable or not needs to be determined after testing. Cell Cycle Product introduction：Product introduction：Cell Cycle Assay Kit Plus ( Cell Cycle Assay Kit Plus ) has certain applicability for live cells and fixed cell cycle detection. For different types of cells, whether it is applicable or not needs to be determined after testing. Cell Cycle Assay Kit Plus ( Cell Cycle Assay Kit Plus ) uses RedNucleus I staining to detect cell cycle. RedNucleus I is a far-infrared nucleic acid dye with cell membrane permeability, which can quickly enter living cells, specifically bind to DNA, and perform cell cycle detection on living cells without RNase digestion. Compared with the traditional PI staining method, the cells do not need to be broken or fixed, and the operation is simpler. RedNucleus I is a fluorescent dye of double-stranded DNA, and the fluorescence intensity after binding to double-stranded DNA is proportional to the content of double-stranded DNA. The intracellular DNA content can be measured by flow cytometry, and then the cell cycle analysis can be carried out according to the distribution of DNA content. After RedNucleus I staining, assuming that the fluorescence intensity of G0 / G1 phase cells is 1, the theoretical value of the fluorescence intensity of G2 / M phase cells containing two copies of genomic DNA is 2, and the fluorescence intensity of S phase cells undergoing DNA replication is between 1-2. In addition, RedNucleus I is compatible with dyes such as Horizon BV / BUV, FITC and R-PE, and can be periodically detected after sample staining.The kit is usually used to detect the cell cycle of cultured adherent or suspended cells. If it is used for cell cycle detection of tissues, the tissues must be digested into a single cell state.Matters needing attention：1. please centrifuge the product to the bottom of the tube immediately before use, and then conduct subsequent experiments. 2. this product is applicable to the detection of living cells and fixed cell cycle with certain limitations. Whether it is applicable to different types of cells needs to be determined after testing. If fixation is needed, it is recommended to use ice bath pre cooling 75-80% ethanol -20 ℃ to fix cells overnight. 3. fluorescent dyes have quenching problems. Please try to avoid light during storage and use to slow down fluorescence quenching. 4. for your safety and health, please wear experimental clothes and disposable gloves.Instruction： Experimental materials ( self-provided )：①cell lines or other cell samples ( self-prepared ) ；②This kit ; ③ trypsin ( self-prepared ) ;④ Cell culture medium containing FBS ( self-prepared ) ; Experimental procedure： 1.Preparation of cell samples : ( 1 ) ( This step is for adherent cells, if suspended cells, can be carried out directly step ( 2 ) ) Digest cells with trypsin, add cell culture medium, gently blow away cells, collected into the centrifuge tube. Note : The number of cells on the machine needs to reach 50,000 and above, so the initial number of cells collected needs to be sufficient. ( 2 ) Centrifuged about 1000 g for 3-5 min to precipitate cells. Carefully remove the supernatant, add about 1 mL of ice bath pre-cooled 1 × staining buffer ( 10 × staining buffer diluted with diH2O at 1 : 10 ), re-suspend the cells. Repeat once. ( 3 ) Centrifuged about 1000 g for 3-5 min to precipitate cells. After the supernatant was discarded, 1 mL of culture medium was added to re-suspend the cells ( for fixed cells, 1 × PBS can also be used to re-suspend ). Gently flick the bottom of the centrifuge tube to properly disperse the cells to avoid cell aggregation. 2.Staining : 4 µL of RedNucleus I staining solution was added to each tube of cell samples, slowly and fully mixed, and incubated at room temperature in dark for 20 min ( or incubated at 37 ° C in dark for 5-10 min ). The optimal incubation time of different cells is different, and the staining time can be adjusted and optimized according to the actual staining effect to obtain a more ideal staining effect. 3.Flow cytometry detection and analysis : Excited at 638 nm by flow cytometry, it is recommended to detect in RL3 or FL4 channels, or use RL1 and RL2 channels. Cell DNA content analysis and light scattering analysis were performed using appropriate analysis software.Scope of application：Cell cycle detection... Read More | This kit is used to extract miRNAs from various animal tissues, plant tissues and cells. The extracted miRNA molecule is complete and high purity, which is suitable for various molecular biology experiments such as Northern blot, real timepcr, miRNA microarray chip, in situ hybridization, This kit is used to extract miRNAs from various animal tissues, plant tissues and cells. The extracted miRNA molecule is complete and high purity, which is suitable for various molecular biology experiments such as Northern blot, real timepcr, miRNA microarray chip, in situ hybridization, RNase protection assay, etcComposition:Scope of application：Nucleic acid extraction and purificationInstruction：1.Experimental preparation：1.1.All reagents were prepared with DEPC-treated solvents. Please use RNase-free tip and centrifuge tube to avoid RNA degradation by RNase during extraction.1.2.70 % ethanol, -20C pre-cooling.2.Operational procedure：There is a slight difference in the operation of miRNA extraction from different samples. The specific steps are as follows :【 Extraction of miRNA from animal tissues】1.Take 20-40 mg tissue, transfer to a pre-cooled mortar, and add liquid nitrogen to grind into powder.Please click below to describe the amount of organization used :①RNA-rich tissue ( e.g. liver ) : no more than 30 mg②Tissues with low RNA content ( e.g., muscle ) : no more than 100 mg③When the amount of tissue used was less than 20 mg : the amount of R-I, R-II and isopropanol used was halved.④When the amount of tissue used was more than 40 mg : the use of R-I, R-II and isopropanol increased proportionally.2.Add 400 ul Buffer R-I, repeatedly aspirate 8-10 times with a syringe equipped with a 21-25 needle, and transfer to a 1.5 m : centrifuge tube ( provided in the kit ). 3.Add 150 µl BufferR-1l, swirl for 15-30 s, centrifuge at 12,000 X g for 5 min. [ Centrifugation at 4 °C is recommended ] 4.Take the supernatant to 1.5ml centrifuge tube, add 180 u anhydrous ethanol, mix evenly.5.The preparation tube was placed in a 2 m : centrifuge tube ( provided in the kit ), the mixture in step 4 was transferred to the preparation tube, and 12,000 X g was centrifuged for 1 min. [ 1 Centrifugation at 4 °C is recommended ; 2 miRNA in the filtrate, pay attention to preserve the filtrate. ]6.Abandon the preparation tube, add 500µl isopropanol to the filtrate, and mix evenly.7.12,000Xg centrifuged for 10 min, discard the supernatant.8.Add 700µl 70 % ethanol ( pre-cooled at -20 °C ), centrifuged at 12,000Xg for 5min.9.The supernatant was discarded and dried at room temperature for 5-10 min.10.70 ul Buffer TE ( nucdease-free ) or RNase-free water was added to the centrifuge tube to elute miRNA.【 Extraction of miRNA from plant tissue 】1.Take 30-150 mg tissue, transfer to a pre-cooled mortar, and add liquid nitrogen to grind into powder.Please click below to describe the amount of organization used :①Plant leaves : usually 10-80 mg② Plant fiber tissue : usually 100-150 mg③When the amount of plant leaf tissue was less than 30 mg : the amount of R-I, R-II and isopropyl alcohol used was halved.④When the amount of plant leaf tissue was more than 80 mg : the use of R-I, R-II and isopropanol increased proportionally.⑤When the amount of plant fiber tissue was more than 150 mg : the use of R-I, R-II and isopropanol increased proportionally.2.Add 400 ul BufferR-I, use a syringe with a 21-25 needle to repeatedly suck 8-10 times, and transfer to a 1.5mI centrifuge tube ( provided in the kit ). 3.Add 150 ul Buffer R-1I, vortex oscillation 15-30 s, 12.000 x g centrifugation 5 min. [ Centrifugation at 4 °C is recommended ]4.Take the supernatant to 1.5ml centrifuge tube, add 180 mountain anhydrous ethanol, mix evenly.The preparation tube was placed in a 2 mI centrifuge tube ( provided in the kit ), the mixture in step 4 was transferred to the preparation tube, and 12.000 xg was centrifuged for 1 min. It is recommended to centrifuge at 4 °C ; 2 miRNA in the filtrate, pay attention to preserve the filtrate. ]Abandon the preparation tube, add 500µl isopropanol to the filtrate, and mix evenly.7.12,000xg high heart for 10 min, discard the supernatant.8.Add 700 ul 70 % ethanol ( -20 °C precooling ), 12,000 xg centrifuge for 5 min.9.The supernatant was discarded and dried at room temperature for 5-10 min.10.70 ul Buffer TE ( nucdease-free ) or RNase-free water was added to the centrifuge tube to elute miRNA.【miRNA extraction from cells】Steps 1-3 According to the different ways of cell culture, two experimental methods, a or b, can be selected.a. Suspension cultured animal cells or cell suspension obtained from petri dishes or culture flasks or freshly isolated animal tissue single cell suspension :1a.Collect 2X 10 * -1X 10 ' cells, centrifuge 2,000Xg for 5 min, discard the supernatant ;2a. Add 400 µl Buffer R-I, repeatedly draw 8-10 times with a syringe containing 21-25 needles, and transfer to a 1.5 mI centrifuge tube ( provided in the kit ) ;3a. Add 150µl Buffer R1I, vortex oscillation 15-30s, 12.000Xg centrifugal 5min. [ build at 4 °C centrifugal ].b. Cells cultured on 96-well L, 24-well, 12-well or 6-well plates :Cells were collected from 96-well, 24-well, 12-well or 6-well culture plates, and the medium was discarded as much as possible, and 400 u / well Buffer R-I was added to each well, and the pipette gun was used to blow up and down 8-10 times ;2b.Transfer the above cell suspension to a 1.5ml centrifuge tube ( provided in the kit ), and repeatedly draw 8-10 times with a syringe containing 21-25 needles ;3b. Add 150 µl Bufflr R-II, swirl for 15-30 s, centrifuge for 5 min at 12,000 × g. [ Recommended at 4 °C ]4.Take the supernatant to 1.5ml centrifuge tube, add 180 mountain anhydrous ethanol, mixing evenly.5.The preparation tube was placed in a 2 ml centrifuge tube ( provided in the kit ), the mixture in step 4 was transferred to the preparation tube, and centrifuged at 12.000 Xg for 1 min. [ 1 Centrifugation at 4 °C is recommended ; 2 miRNA in the filtrate, pay attention to preserve the filtrate. ]6.Abandon the preparation tube, add 500 u of isopropanol to the filtrate, and mix evenly.7.12,000Xg high heart for 10 min, discard the supernatant.8.Add 700µ70 % ethanol ( pre-cooled at − 20 °C ), centrifuged at 12,000 × g for 5 min.9.Abandon the supernatant, dry at room temperature for 5 - 10 min.10.70 ul Bufer TE ( nucdease-free ) or RNase-free water was added to the centrifuge tube to elute mRNA.3.Flow chartMatters needing attention：Buffer R-I contains irritating compounds, when operating to wear latex gloves and glasses, to avoid contamination of the skin, eyes and clothes, be careful not to inhale the nose and mouth. If the skin, eyes, to immediately rinse with a lot of water or saline, if necessary, seek medical advice... Read More | Product content： Component S665549 50 preps Buffer SW 60 ml Buffer SL 60 ml Buffer GL 50 ml Buffer GW1（concentrate） 2X13 ml Buffer GW2（concentrate） 15 ml Buffer GE 15 ml Spin Columns DM 50 with Collection Tubes 50Product IntroductionThis kit is suitable for Product content： Component S665549 50 preps Buffer SW 60 ml Buffer SL 60 ml Buffer GL 50 ml Buffer GW1（concentrate） 2X13 ml Buffer GW2（concentrate） 15 ml Buffer GE 15 ml Spin Columns DM 50 with Collection Tubes 50Product IntroductionThis kit is suitable for extracting total DNA from fecal samples, including the total DNA of cells, bacteria, parasites, and viruses in the samples, as well as samples containing high concentrations of PCR reaction inhibitors. This product can process up to 300 mg of fecal samples and purify to obtain mainly 20-30 kb DNA fragments. The purification process does not require toxic solvents such as phenol or chloroform, and does not require ethanol precipitation. High purity DNA can be obtained within one hour. This reagent kit adopts a unique buffering system to efficiently bind DNA from the lysis solution to the adsorption column. At the same time, protein impurities and other organic compounds that inhibit downstream reactions in feces can flow through the membrane. Inhibitors of PCR and enzyme reactions, as well as residual impurities, can be effectively removed through two washing steps. Finally, high-purity DNA can be obtained by washing with low salt buffer or water. The purified DNA can be directly used for downstream experiments such as enzyme digestion, PCR, Real Time PCR, library construction, Southern Blot, and molecular labeling.Preparation and important precautions before the experiment1. Samples should avoid repeated freeze-thaw cycles, otherwise it may result in smaller extracted DNA fragments and a decrease in extraction volume.2.Before the first use, anhydrous ethanol should be added to Buffer GW1 and GW2 according to the instructions on the reagent bottle label.3. Before use, please check whether there is crystallization or precipitation in Buffer SL and Buffer GL. If there is crystallization or precipitation, please dissolve Buffer SL and Buffer GL again in a 56 ℃ water bath.4. If downstream experiments are sensitive to RNA contamination, 4 can be added after adding Buffer SL µ RNase A of DNase Free (100 mg/ml) is not provided in this kit. If needed, it can be ordered separately from our company, item number: S665549Operation steps1. Take a fecal sample of 100-300 mg and place it in a centrifuge tube (provided by oneself).2. Add 1 ml of Buffer SW and vortex for 3-5 minutes to evenly disperse the sample in the solution. Centrifuge at 12000 rpm (~13400 × g) for 1 minute and discard the supernatant.3. Add 1 ml of Buffer SL and vortex for 3-5 minutes to evenly disperse the sample in the solution. Take a water bath at 65 ℃ for 20 minutes and vortex for 15 seconds every 5 minutes. Note: To remove RNA, add 4 after completing the above steps µ RNase A solution (product number: CW0601S) with a concentration of 100 mg/ml, shake well and let stand at room temperature for 5-10 minutes.4.Centrifuge at 2000 rpm for 3 minutes and transfer the supernatant to a new centrifuge tube (provided by oneself).5. Add an equal volume of Buffer GL to the supernatant, invert and mix 15-25 times, and leave on ice for 5 minutes. Centrifuge at 12000 rpm for 5 minutes. Attention: At this time, the liquid may be in a transparent or turbid state, which does not affect the experiment. 6. Add the supernatant obtained in step 5 to the spin columns DM that have been loaded into the collection tube. If the solution cannot be added at once, it can be transferred multiple times. Centrifuge at 12000 rpm (~13400 × g) for 1 minute, discard the waste liquid in the collection tube, and place the adsorption column back into the collection tube.7. Add 500 to the adsorption column µ Buffer GW1 (check if anhydrous ethanol has been added before use), centrifuge at 12000 rpm for 1 minute, discard the waste liquid in the collection tube, and place the adsorption column back into the collection tube. 8. Repeat step 7.9. Add 500 to the adsorption column µ Buffer GW2 (check if anhydrous ethanol has been added before use), centrifuge at 12000 rpm for 1 minute, discard the waste liquid in the collection tube, and place the adsorption column back into the collection tube.10.12000 rpm for 2 minutes and discard the waste liquid from the collection tube. Place the adsorption column at room temperature for a few minutes to thoroughly air dry. Note: The purpose of this step is to remove residual ethanol from the adsorption column, which can affect subsequent enzymatic reactions (such as enzyme digestion, PCR, etc.).11. Place the adsorption column in a new centrifuge tube (self provided) and add 50-100 drops of suspended droplets to the middle of the adsorption column µ L Buffer GE or sterilized water, leave at room temperature for 2-5 minutes, centrifuge at 12000 rpm for 1 minute, collect DNA solution, and store DNA at -20 ℃.Note: 1) If downstream experiments are sensitive to pH or EDTA, they can be washed off with sterilized water. The pH value of the eluent has a significant impact on the elution efficiency. If water is used as the eluent, its pH value should be ensured to be between 7.0-8.5 (NaOH can be used to adjust the pH value of the water to this range). When the pH value is below 7.0, the elution efficiency will be reduced2) Incubating at room temperature for 5 minutes before centrifugation can increase yield.3) Use an additional 50-100 µ Further washing with buffer GE or sterilized water can increase yield.4) If you want to increase the final concentration of DNA, you can add the DNA eluent obtained in step 11 back onto the adsorption membrane and repeat step 11; It is possible to increase the final concentration of DNA, but it may reduce the total yield. If the amount of DNA is less than 1 µ g. Recommended 50 µ Wash with buffer GE or sterilized water.5) DNA stored in water can be affected by acidic hydrolysis. If long-term storage is required, it is recommended to elute with Buffer GE and store at -20 ℃.6) The residual trace PCR inhibitors in the genomic DNA template may have adverse effects on the PCR reaction, which can be solved by diluting DNA by 2-10 times... Read More |