| Description | Inquire | EndoFree Plasmid Midi Kit Cat No. Component Size（50T） Storage E665631A Buffer P1 30 mL RT E665631B Buffer P2 30 mL RT E665631C Buffer E3 30 mL RT E665631D Buffer PS 15 mL RT E665631E Buffer PW (concentrate) 10 mL RT E665631F Endo-free Buffer EB 10 mL RTEndoFree Plasmid Midi Kit Cat No. Component Size（50T） Storage E665631A Buffer P1 30 mL RT E665631B Buffer P2 30 mL RT E665631C Buffer E3 30 mL RT E665631D Buffer PS 15 mL RT E665631E Buffer PW (concentrate) 10 mL RT E665631F Endo-free Buffer EB 10 mL RT E665631G RNase A (10 mg/mL) 600 µL RT E665631H Buffer ER 8 mL RT E665631I CWBlue 300 µL RT E665631J Spin Columns DL with Collection Tubes 50 EA RT E665631K Endo-Remover FM with Collection 50 EA RTProduct Introduction:Endotoxins are a common pollutant in plasmid extraction. Due to the high sensitivity of eukaryotic cells to endotoxins, the presence of endotoxins in plasmids can greatly reduce the transfection efficiency of eukaryotic cells. This reagent kit provides a simple, fast, and efficient new method for extracting endotoxin free plasmids. The extracted plasmids can remove endotoxins to the maximum extent possible and effectively remove contamination of genomic DNA, RNA, proteins, and other substances. This reagent kit is suitable for extracting 5-15mL of bacterial solution. On the basis of alkaline lysis of cells, it efficiently and specifically binds plasmid DNA through a new silicon-based membrane. Each adsorption column can adsorb up to 100 µ The plasmid DNA of g is effectively removed using a special buffer system and endotoxin removal filter column, effectively removing impurities such as endotoxins and proteins. The plasmid obtained from this kit has high purity and stable quality, making it particularly suitable for cell transfection. It can also be used for downstream experiments such as DNA sequencing, PCR, PCR based mutations, in vitro transcription, transformed bacteria, and endonuclease digestion.Self prepared reagents: anhydrous ethanol, isopropanol.Preparation and important precautions before the experiment:1. All components can be stably stored in a dry, room temperature (15-30 ℃) environment for 1 year, and can be stored at 2-8 ℃ for longer periods of time. Buffer P1 with RNase A added can be stably stored at 2-8 ℃ for 6 months.2. Before the first use, add all RNase A solution to Buffer P1, mix well, and store at 2-8 ℃. Before use, let it sit at room temperature for a period of time. After returning to room temperature, use.3.Before the first use, anhydrous ethanol should be added to the Buffer PW according to the instructions on the reagent bottle label.4. Before use, please check if there is any crystallization or precipitation in Buffer P2 and Buffer E3. If there is any crystallization or precipitation, you can take a water bath at 37 ℃ for a few minutes to restore clarity.5. Be careful not to come into direct contact with Buffer P2 and Buffer E3, and immediately cover them tightly after use.6.The amount and purity of plasmid extraction are related to factors such as bacterial culture concentration, strain type, plasmid size, and plasmid copy number.Operation steps:1. Take 5-15 mL of overnight cultured bacterial solution and add it to a centrifuge tube (self provided). Centrifuge at 13000 rpm (~16200 × g) for 1 minute to collect bacteria, and try to discard all the supernatant as much as possible.2. Add 500 to the centrifuge tube containing bacterial sediment µ L Buffer P1 (please check if RNase A has been added first), mix thoroughly with a pipette or vortex oscillator, and suspend bacterial precipitation. Attention: If the bacterial blocks are not thoroughly mixed, it will affect the cracking effect, resulting in low extraction amount and purity.3. Add 500 to the centrifuge tube µ L Buffer P2, gently invert and mix 8-10 times, allowing the bacterial cells to fully lyse. Leave at room temperature for 3-5 minutes. At this point, the solution should become clear and viscous. Attention: Mix gently and do not shake vigorously to avoid interrupting genomic DNA and mixing genomic DNA fragments in the extracted plasmid. If the solution does not become clear, it indicates that the bacterial count may be too high and the lysis may not be complete. The bacterial count should be reduced.4. Add 500 to the centrifuge tube µ L Buffer E3, immediately invert and mix 8-10 times until white flocculent precipitates appear. Let it stand at room temperature for 5 minutes. Centrifuge at 13000 rpm for 5 minutes, extract the supernatant, and add it to the filter column (Endo Remove FM) (already loaded into the collection tube). Centrifuge at 13000 rpm for 1 minute to filter, then transfer the filtrate from the collection tube to the centrifuge tube (self provided). Attention: 1) After adding Buffer E3, it should be immediately mixed to avoid local precipitation. 2) The maximum volume of the adsorption column is 750 µ L. So please filter the supernatant twice and mix it in the same self provided centrifuge tube.5. Add 450 to the filtrate µ Mix L isopropanol upside down.6. Column balance: Add 200 to the spin columns DL that have been loaded into the collection tube µ L Buffer PS, centrifuge at 13000 rpm for 2 minutes, discard the waste liquid in the collection tube, and place the adsorption column back into the collection tube.7. Transfer the mixed solution of filtrate and isopropanol from step 5 to an equilibrium adsorption column (already loaded into a collection tube). 8.13000 rpm for 1 minute, discard the waste liquid in the collection tube, and place the adsorption column back into the collection tube. Attention: The maximum volume of the adsorption column is 750 µ L. So the solution obtained in step 5 is divided multiple times and passed through the column. 9. Add 750 to the adsorption column µ L Buffer PW (please check if anhydrous ethanol has been added first), centrifuge at 13000 rpm for 1 minute, and discard the waste liquid in the collection tube.10. Place the adsorption column back into the recovery manifold and centrifuge at 13000 rpm for 1 minute.Note: The purpose of this step is to remove residual ethanol from the adsorption column, which can affect subsequent enzymatic reactions (such as enzyme digestion, PCR, etc.).11. Place the adsorption column in a new centrifuge tube (self provided)... Read More | This kit is used to extract miRNAs from various animal tissues, plant tissues and cells. The extracted miRNA molecule is complete and high purity, which is suitable for various molecular biology experiments such as Northern blot, real timepcr, miRNA microarray chip, in situ hybridization, This kit is used to extract miRNAs from various animal tissues, plant tissues and cells. The extracted miRNA molecule is complete and high purity, which is suitable for various molecular biology experiments such as Northern blot, real timepcr, miRNA microarray chip, in situ hybridization, RNase protection assay, etcComposition:Scope of application：Nucleic acid extraction and purificationInstruction：1.Experimental preparation：1.1.All reagents were prepared with DEPC-treated solvents. Please use RNase-free tip and centrifuge tube to avoid RNA degradation by RNase during extraction.1.2.70 % ethanol, -20C pre-cooling.2.Operational procedure：There is a slight difference in the operation of miRNA extraction from different samples. The specific steps are as follows :【 Extraction of miRNA from animal tissues】1.Take 20-40 mg tissue, transfer to a pre-cooled mortar, and add liquid nitrogen to grind into powder.Please click below to describe the amount of organization used :①RNA-rich tissue ( e.g. liver ) : no more than 30 mg②Tissues with low RNA content ( e.g., muscle ) : no more than 100 mg③When the amount of tissue used was less than 20 mg : the amount of R-I, R-II and isopropanol used was halved.④When the amount of tissue used was more than 40 mg : the use of R-I, R-II and isopropanol increased proportionally.2.Add 400 ul Buffer R-I, repeatedly aspirate 8-10 times with a syringe equipped with a 21-25 needle, and transfer to a 1.5 m : centrifuge tube ( provided in the kit ). 3.Add 150 µl BufferR-1l, swirl for 15-30 s, centrifuge at 12,000 X g for 5 min. [ Centrifugation at 4 °C is recommended ] 4.Take the supernatant to 1.5ml centrifuge tube, add 180 u anhydrous ethanol, mix evenly.5.The preparation tube was placed in a 2 m : centrifuge tube ( provided in the kit ), the mixture in step 4 was transferred to the preparation tube, and 12,000 X g was centrifuged for 1 min. [ 1 Centrifugation at 4 °C is recommended ; 2 miRNA in the filtrate, pay attention to preserve the filtrate. ]6.Abandon the preparation tube, add 500µl isopropanol to the filtrate, and mix evenly.7.12,000Xg centrifuged for 10 min, discard the supernatant.8.Add 700µl 70 % ethanol ( pre-cooled at -20 °C ), centrifuged at 12,000Xg for 5min.9.The supernatant was discarded and dried at room temperature for 5-10 min.10.70 ul Buffer TE ( nucdease-free ) or RNase-free water was added to the centrifuge tube to elute miRNA.【 Extraction of miRNA from plant tissue 】1.Take 30-150 mg tissue, transfer to a pre-cooled mortar, and add liquid nitrogen to grind into powder.Please click below to describe the amount of organization used :①Plant leaves : usually 10-80 mg② Plant fiber tissue : usually 100-150 mg③When the amount of plant leaf tissue was less than 30 mg : the amount of R-I, R-II and isopropyl alcohol used was halved.④When the amount of plant leaf tissue was more than 80 mg : the use of R-I, R-II and isopropanol increased proportionally.⑤When the amount of plant fiber tissue was more than 150 mg : the use of R-I, R-II and isopropanol increased proportionally.2.Add 400 ul BufferR-I, use a syringe with a 21-25 needle to repeatedly suck 8-10 times, and transfer to a 1.5mI centrifuge tube ( provided in the kit ). 3.Add 150 ul Buffer R-1I, vortex oscillation 15-30 s, 12.000 x g centrifugation 5 min. [ Centrifugation at 4 °C is recommended ]4.Take the supernatant to 1.5ml centrifuge tube, add 180 mountain anhydrous ethanol, mix evenly.The preparation tube was placed in a 2 mI centrifuge tube ( provided in the kit ), the mixture in step 4 was transferred to the preparation tube, and 12.000 xg was centrifuged for 1 min. It is recommended to centrifuge at 4 °C ; 2 miRNA in the filtrate, pay attention to preserve the filtrate. ]Abandon the preparation tube, add 500µl isopropanol to the filtrate, and mix evenly.7.12,000xg high heart for 10 min, discard the supernatant.8.Add 700 ul 70 % ethanol ( -20 °C precooling ), 12,000 xg centrifuge for 5 min.9.The supernatant was discarded and dried at room temperature for 5-10 min.10.70 ul Buffer TE ( nucdease-free ) or RNase-free water was added to the centrifuge tube to elute miRNA.【miRNA extraction from cells】Steps 1-3 According to the different ways of cell culture, two experimental methods, a or b, can be selected.a. Suspension cultured animal cells or cell suspension obtained from petri dishes or culture flasks or freshly isolated animal tissue single cell suspension :1a.Collect 2X 10 * -1X 10 ' cells, centrifuge 2,000Xg for 5 min, discard the supernatant ;2a. Add 400 µl Buffer R-I, repeatedly draw 8-10 times with a syringe containing 21-25 needles, and transfer to a 1.5 mI centrifuge tube ( provided in the kit ) ;3a. Add 150µl Buffer R1I, vortex oscillation 15-30s, 12.000Xg centrifugal 5min. [ build at 4 °C centrifugal ].b. Cells cultured on 96-well L, 24-well, 12-well or 6-well plates :Cells were collected from 96-well, 24-well, 12-well or 6-well culture plates, and the medium was discarded as much as possible, and 400 u / well Buffer R-I was added to each well, and the pipette gun was used to blow up and down 8-10 times ;2b.Transfer the above cell suspension to a 1.5ml centrifuge tube ( provided in the kit ), and repeatedly draw 8-10 times with a syringe containing 21-25 needles ;3b. Add 150 µl Bufflr R-II, swirl for 15-30 s, centrifuge for 5 min at 12,000 × g. [ Recommended at 4 °C ]4.Take the supernatant to 1.5ml centrifuge tube, add 180 mountain anhydrous ethanol, mixing evenly.5.The preparation tube was placed in a 2 ml centrifuge tube ( provided in the kit ), the mixture in step 4 was transferred to the preparation tube, and centrifuged at 12.000 Xg for 1 min. [ 1 Centrifugation at 4 °C is recommended ; 2 miRNA in the filtrate, pay attention to preserve the filtrate. ]6.Abandon the preparation tube, add 500 u of isopropanol to the filtrate, and mix evenly.7.12,000Xg high heart for 10 min, discard the supernatant.8.Add 700µ70 % ethanol ( pre-cooled at − 20 °C ), centrifuged at 12,000 × g for 5 min.9.Abandon the supernatant, dry at room temperature for 5 - 10 min.10.70 ul Bufer TE ( nucdease-free ) or RNase-free water was added to the centrifuge tube to elute mRNA.3.Flow chartMatters needing attention：Buffer R-I contains irritating compounds, when operating to wear latex gloves and glasses, to avoid contamination of the skin, eyes and clothes, be careful not to inhale the nose and mouth. If the skin, eyes, to immediately rinse with a lot of water or saline, if necessary, seek medical advice... Read More | The content of this cell is too long for an XLSX file (more than 32767 characters). Please use the CSV format for this export | Product introduction：This kit uses an improved SDS alkaline lysis method combined with DNA preparation membrane to selectively adsorb DNA to achieve the purpose of rapid purification of plasmid DNA. It is suitable for extracting up to 500ug of high-purity plasmid DNA from 120-300ml bacterial Product introduction：This kit uses an improved SDS alkaline lysis method combined with DNA preparation membrane to selectively adsorb DNA to achieve the purpose of rapid purification of plasmid DNA. It is suitable for extracting up to 500ug of high-purity plasmid DNA from 120-300ml bacterial culture for sequencing, in vitro transcription and translation, restriction enzyme digestion, bacterial transformation and other molecular biology experiments.Scope of application：Nucleic acid extraction and purification... Read More |