| Description | Glucokinase (GK, EC 2.7.1.2) is a member of the hexokinase family, primarily found in mature hepatocytes and pancreatic islet cells. Under normal physiological conditions, the main role of GK is to monitor blood glucose levels. Detection Principle: Glucokinase (GK) phosphorylates glucose to produce Glucokinase (GK, EC 2.7.1.2) is a member of the hexokinase family, primarily found in mature hepatocytes and pancreatic islet cells. Under normal physiological conditions, the main role of GK is to monitor blood glucose levels. Detection Principle: Glucokinase (GK) phosphorylates glucose to produce glucose-6-phosphate. This product is further coupled with glucose-6-phosphate dehydrogenase and NADP⁺. The increase in NADPH absorbance at 340 nm is measured, allowing for the calculation of the enzyme's activity.Component100TStorageExtraction Buffer120 mL2-8℃Reagent 120 mL2-8℃Reagent 21EA-20℃Reagent 31EA2-8℃Reagent 2 (Powder, 1 vial) Preparation:Before use, centrifuge at 8000 g, 4°C for 2 minutes to collect the powder at the bottom of the tube (can be flicked manually).Add 1.1 mL of distilled water to dissolve. Use after preparation.The prepared solution can be stored for the duration of the kit's validity period.Reagent 3 (Powder, 1 vial) Preparation:Before opening, ensure the powder is at the bottom (can be flicked manually).Add 18 mL of Reagent 1 to dissolve. Use after preparation.The prepared solution can be stored for the duration of the kit's validity period.User-Prepared Instruments and MaterialsMortar (Homogenizer), Ice box (Ice maker), Benchtop centrifuge, Adjustable micropipettes, Water bath (Oven, Incubator, Metal bath), 96-well plate, Centrifuge tubes, Microplate reader, Distilled water (Deionized water or Ultrapure water are also acceptable).Experimental ProcedureIt is recommended to first perform a preliminary test using 1-3 samples with expected significant differences (e.g., different types or groups) to familiarize yourself with the procedure and to determine or adjust sample concentrations based on the preliminary results, preventing unnecessary waste of samples or reagents.1. Sample Extraction1.1 Tissue SamplesWeigh approximately 0.1 g of tissue. Add 1 mL of Extraction Buffer and homogenize in an ice bath. Centrifuge at 12,000 rpm, 4°C for 10 minutes. Collect the supernatant and keep it on ice for assay.Note: If increasing the sample amount, maintain a tissue mass (g) to Extraction Buffer volume (mL) ratio between 1:5 and 1:10.1.2 Bacterial/Cell SamplesCollect bacteria or cells into a centrifuge tube, centrifuge, and discard the supernatant. Add 1 mL of Extraction Buffer per 5 million bacteria/cells. Disrupt the bacteria or cells by sonication in an ice bath (power 20% or 200W, pulse 3s on, 10s off, repeat 30 times). Centrifuge at 12,000 rpm, 4°C for 10 minutes. Collect the supernatant and keep it on ice for assay.Note: If increasing the sample amount, maintain a bacteria/cell count (10⁴) to Extraction Buffer volume (mL) ratio between 500:1 and 1000:1.1.3 Liquid SamplesAssay directly. If turbid, centrifuge and use the supernatant for assay.2. Assay Steps2.1 Preheat the microplate reader for at least 30 minutes. Set the wavelength to 340 nm.2.2 Pre-warm the prepared Reagent 2 and Reagent 3 at 25°C for 5 minutes to reach room temperature.2.3 Add reagents sequentially to a 96-well plate:ReagentTest Well (µL)Sample20Reagent 210Reagent 3170Mix thoroughly. Read the absorbance at 340 nm at 1 minute (A₁) and again at 21 minutes (A₂, i.e., after 20 minutes of reaction). Calculate ΔA = A₂ - A₁.Note:If ΔA is close to zero, the reaction time can be appropriately extended to 30 minutes or longer before reading A₂. If the reaction time is changed, the new time (T) must be substituted into the calculation formula. Alternatively, the sample volume can be increased; the new sample volume (V₁) must then be substituted into the calculation formula.If the increase trend is unstable, read the absorbance every 10 seconds and select a linearly increasing time period for calculation. The corresponding A values for this period should be used to calculate ΔA and substituted into the formula.3. Calculation of Results3.1 Based on Sample Protein ConcentrationUnit Definition: One unit of enzyme activity is defined as the amount that produces 1 nmol of NADPH per minute per mg of tissue protein.Derived Formula: GK (nmol/min/mg prot) = [ΔA ÷ (ε × d) × V₂ × 10⁹] ÷ (V₁ × Cpr) ÷ TSimplified Formula: GK (nmol/min/mg prot) = 160.77 × ΔA ÷ Cpr3.2 Based on Sample Fresh WeightUnit Definition: One unit of enzyme activity is defined as the amount that produces 1 nmol of NADPH per minute per gram of tissue.Derived Formula: GK (nmol/min/g fresh weight) = [ΔA ÷ (ε × d) × V₂ × 10⁹] ÷ (W × V₁ ÷ V) ÷ TSimplified Formula: GK (nmol/min/g fresh weight) = 160.77 × ΔA ÷ W3.3 Based on Bacterial or Cell DensityUnit Definition: One unit of enzyme activity is defined as the amount that produces 1 nmol of NADPH per minute per 10⁴ bacteria or cells.Derived Formula: GK (nmol/min/10⁴ cells) = [ΔA ÷ (ε × d) × V₂ × 10⁹] ÷ (500 × V₁ ÷ V) ÷ TSimplified Formula: GK (nmol/min/10⁴ cells) = 0.32 × ΔA3.4 Based on Liquid VolumeUnit Definition: One unit of enzyme activity is defined as the amount that produces 1 nmol of NADPH per minute per mL of liquid.Derived Formula: GK (nmol/min/mL) = [ΔA ÷ (ε × d) × V₂ × 10⁹] ÷ V₁ ÷ TSimplified Formula: GK (nmol/min/mL) = 160.77 × ΔAParameter Definitions:ε: Molar extinction coefficient of NADPH (6.22 × 10³ L/mol/cm)d: Light path length for the 96-well plate (0.5 cm)V: Volume of Extraction Buffer added (1 mL)V₁: Volume of sample added to the reaction (0.02 mL)V₂: Total volume of the reaction system (0.2 mL = 2.0 × 10⁻⁴ L)T: Reaction time (20 minutes)W: Sample weight (g)500: Total number of bacteria or cells (5 million)Cpr: Sample protein concentration (mg/mL); Aladdin's BCA Protein Quantification Kit (B665595) or Ready-to-Use BCA Protein Quantification Kit (R1491648) is recommended.PrecautionsIt is strongly recommended to first perform a preliminary test using 1-3 samples with expected significant differences (e.g., different types or groups) to familiarize yourself with the procedure. Based on the preliminary results, determine or adjust sample concentrations to prevent unnecessary waste of samples or reagents... Read More | The bacterial viability / toxicity detection kit contains two fluorescent dyes. Nucgreen is a green nucleic acid dye that can stain live and dead bacteria; Ethd III is a red nucleic acid dye that only stains dead bacteria with damaged cell membranes. When nucgreen and ethd III are properly mixed, The bacterial viability / toxicity detection kit contains two fluorescent dyes. Nucgreen is a green nucleic acid dye that can stain live and dead bacteria; Ethd III is a red nucleic acid dye that only stains dead bacteria with damaged cell membranes. When nucgreen and ethd III are properly mixed, the bacteria with intact cell membrane appear green, while the bacteria with damaged cell membrane can appear green and red under different channels, respectively. A common criterion for bacterial viability is the ability to propagate in a suitable nutrient medium, known as a growth assay. This kit is generally in good agreement with the growth assay results in liquid or solid medium. However, under certain conditions, membrane damaged bacteria may recover and propagate in nutrient medium, and such bacteria will be identified as dead bacteria in this assay. On the contrary, some bacteria with intact membranes may not be able to propagate in nutrient medium, but will be recognized as viable bacteria in this assay. Therefore, if there is a large difference between the test results of this kit and the bacterial growth assay, the above possibilities should be considered. Component： Product parameters： NucGreen: Ex/Em = 503/530 nm (结合 DNA)；EthD-III: Ex/Em = 530/620 nm (结合 DNA)。Usage:1 Preparation of control samples for live and dead bacteria (optional)1. Cultivate 4 mL of bacteria in liquid medium until late logarithmic phase.2. Prepare two 1 mL bacterial solutions in an EP tube and centrifuge for 10-15 minutes under 5000-10000 g conditions.3. Remove the supernatant and add 0.3 mL of 0.85% NaCl resuspended bacteria to one of the EP tubes, and 1 mL of 0.85% NaCl resuspended bacteria to the other tube.4. Add 0.7 mL of isopropanol to a tube containing 0.3 mL of 0.85% NaCl, and mix thoroughly (with a final concentration of 70% isopropanol) to prepare a dead bacterial sample.5. Incubate the two samples at room temperature for 1 hour and mix every 15 minutes.6. Centrifuge the two samples at 5000-10000 g for 10-15 minutes.7. Remove the supernatant, add 1 mL of 0.85% NaCl to resuspend the bacteria in both samples, and centrifuge again as in step 6.8. Use a spectrophotometer to measure the absorbance values (OD670) of two bacterial suspensions at 670 nm.9. Adjust the density of the two bacterial suspensions (live and dead) to 108 bacteria/mL (OD670 ≈ 0.3), and then dilute with 0.85% NaCl at 1:100 to achieve a final density of 106 bacteria/mL.10. Mix two bacterial suspensions as shown in the table below to obtain the required live cell ratio: dead cell ratio.Table 1 Mix live and dead bacterial suspensions by a certain volume to achieve the required ratio of live and dead cellsLive cells: Dead cellsVolume of viable bacterial suspension（mL）Volume of dead bacterial suspension（mL）0:10001.010:900.10.920:800.20.830:700.30.750:500.50.5100:01.00II Staining methods for fluorescence microscopy observation1. Mix 1 volume of component A, NucGreen, and 2 volumes of component B, EthD-III, in a microcentrifuge tube. After thorough mixing, add 8 volumes of 0.85% NaCl solution to obtain a 100 x dye solution.2. Every 100 µ L bacterial suspension, add 1 µ 100 x dye solution of L.3. Mix thoroughly and incubate at room temperature in the dark for 15 minutes.4. Take 5 µ The bacterial suspension after L staining was dropped onto a glass slide with an 18 mm square cover glass.5. Observe under a fluorescence microscope. The fluorescence of live and dead bacteria can be observed simultaneously under any standard FITC long-acting filter. Alternatively, live (green fluorescent) and dead (red fluorescent) bacteria can be observed using FITC and Cy3 (or Texas Red) channels, respectively.Attention: (1) Before staining bacteria, attention must be paid to removing residues of growth media. Nucleic acid and other media components can bind to NucGreen and EthD-III dyes in some way, resulting in unacceptable staining changes. A simple washing step is usually sufficient to remove interfering media components from bacterial suspension. It is not recommended to use phosphate buffer solutions as they can reduce staining efficiency. (2) Before starting the formal experiment, the dye concentration should be adjusted to distinguish between NucGreen labeling live bacteria and EthD-III labeling dead bacteria. The optimal concentration may vary depending on the bacterial strain. It is generally best to use the lowest dye concentration that can provide sufficient signal. The above conditions have been optimized for staining live/dead cells of Escherichia coli.III Before starting the staining method experiment of flow cytometry, please read the precautions under the fluorescence microscope staining steps.According to Table 1, add 11 different proportions of live and dead bacteria to the EP tube. Each of the 11 samples has a volume of 1 mL.2. Add 12 µ The A component of L, NucGreen, and 24 µ The B component EthD-III of L was mixed in a microcentrifuge tube. Add 3 to each of the 11 samples µ Mix the mixed dyes of L thoroughly by blowing them up and down several times. (Note: Additional control bacterial samples need to be prepared for separate NucGreen and EthD-III staining)3. Incubate at room temperature in the dark for 15 minutes.4. Analyze each sample using a flow cytometer, detect NucGreen positive cells using FITC channels, and detect EthD-III positive cells using PI or PE channels.Matters needing attention：1. please centrifuge the product to the bottom of the tube immediately before use, and then conduct subsequent experiments. 2. if the orifice plate is used for detection, a small amount of bacterial liquid can be left for imaging after standing for 10 min, which can effectively reduce the background. 3. in order to be closer to the real results, it is recommended to keep the brightness of red fluorescence consistent with that of green fluorescence in merge pictures. 4. fluorescent dyes have quenching problems. Please try to avoid light during experimental operation to slow down fluorescence quenching. 5. for your safety and health, please wear experimental clothes and disposable gloves.Scope of application：Staining of dead and live bacteria... Read More | CFDASE cell proliferation and tracking detection kit is a kit for cell proliferation and tracking detection based on CFDA se. This kit is composed of CFDASE powder, solvent and staining buffer. CFDASE is a derivative of fluorescein diacetate (FDA), which has cell membrane permeability and CFDASE cell proliferation and tracking detection kit is a kit for cell proliferation and tracking detection based on CFDA se. This kit is composed of CFDASE powder, solvent and staining buffer. CFDASE is a derivative of fluorescein diacetate (FDA), which has cell membrane permeability and does not have fluorescence luminescence. When CFDASE penetrates the cell membrane into living cells, it can be catalysed by esterases in the cytosol to produce carboxyfluorescein succinimidyl ester (CFSE), which can emit strong green fluorescence, cannot penetrate the cell membrane, and can remain intact in the cell. CFSE can also spontaneously and irreversibly covalently bind to intracellular amino groups to couple to cellular proteins. Meanwhile, the excess and uncoupled CFDASE returned to the extracellular medium by passive diffusion and was cleared by subsequent washing steps. The fluorescence of non dividing cells labeled by CFDASE is very stable, and the stable labeling time can reach several months, so it is very suitable for cell community analysis. The fluorescence of CFDASE labeled cells is very homogeneous, which is superior to other cell tracking fluorescent probes used previously, such as PKH26, and the fluorescence distribution of the divided progeny cells is also very uniform. In the process of cell division and proliferation, CFSE labeled fluorescence can be evenly distributed to the two progeny cells, and the fluorescence intensity becomes half of the parental cells. According to the fluorescence intensity, flow cytometer (FL1 channel) can detect undivided cells, cells that divide once (1 / 2 of the fluorescence intensity), twice (1 / 4 of the fluorescence intensity), three times (1 / 8 of the fluorescence intensity), and cells that divide more times. CFDASE can detect up to eight or more cleavages. CFDASE labeled cells can be used for proliferation studies in vitro and in vivo, and have the function of not staining adjacent cells. CFDASE is most commonly used to detect the proliferation of lymphocytes, and can also be used to detect the proliferation of fibroblasts, NK cells and other cells. CFDASE labeled cells showed green fluorescence. In addition to flow cytometry to detect cell proliferation, fluorescence microscopy can also be used for homogeneous staining of cell tracking observation.Components:ComponentsC598182-20TC598182-500TA. CFDA SE1 tube1 tubex5B.CFDA SE solvent20 µL500 µLC.10x CFDA SE Buffer1 mL x250 mLMatters needing attention：1. please centrifuge the product to the bottom of the tube immediately before use, and then conduct subsequent experiments. 2. CFDA and Se are easily hydrolyzed and will deteriorate quickly in aqueous solution. Please avoid contact with water during use. Contact with water during the process of labeling cells is within the permitted range. 3. CFDA se solvent will solidify at lower temperatures such as 4 º C and ice bath and stick to the bottom, wall or cover of the centrifugal tube. It can be used after incubating in a 20-25 º C water bath for a while until it is completely dissolved. 4. this kit optimizes the CFDA se staining system, but users are advised to explore the optimal working concentration and staining time according to their own cell type, culture conditions and application direction. Different cells have different lactonase activities, so the staining effect is different. 5. fluorescent dyes have quenching problems. Please avoid light during operation to slow down fluorescence quenching. 6. for your safety and health, please wear experimental clothes and disposable gloves.Usage method:1. Preparation of reagents(1) Preparation of CFDA SE storage solution: Take one tube of CFDA SE provided in the reagent kit and restore it to room temperature. Instantly centrifuge to allow the powder to fully settle to the bottom of the tube. Add 100 µ L CFDA SE solvent (add 20 µ L CFDA SE solvent) to it and dissolve it thoroughly to prepare CFDA SE storage solution (1000 ×). Prepared CFDA SE storage solution, stored at -20 ℃ in the dark, with a shelf life of two months- Storing at 70 ℃ in the dark can extend the usage time appropriately.(2) Preparation of CFDA SE Buffer: Dilute 10 x CFDA SE Buffer to 1 x with sterile cell culture grade water as needed. The prepared 1 × CFDA SE Buffer can be stored at 4 ℃ and can be stored at -20 ℃ if not in use for a long time.2. Marking and detection(1) Centrifuge the collected cells, use 1 mL 1 × CFDA SE Buffer to re suspend the cells in a 15 mL centrifuge tube, and adjust the cell concentration to 1-5 × 106 cells/mL.(2) Preparation of CFDA SE working solution: Dilute the CFDA SE storage solution (1000 ×) with 1 × CFDA SE Buffer to 2 ×.(3) Staining: Add 1 mL of CFDA SE working solution (2 x) to 1 mL of cell suspension to be labeled, invert and mix well, and incubate at 37 ℃ for 10 minutes.(4) Immediately add 5 times the volume of preheated complete culture medium (including serum) to the centrifuge tube, invert and mix well to terminate the labeling reaction.(5) Centrifuge at 1000 rpm for 5 minutes at room temperature to remove the supernatant, then wash once with 5-10 mL of complete culture medium.(6) Add 5-10 mL of complete culture medium and incubate at 37 ℃ for 5 minutes to promote the residence of CFDA SE in the cells and the entry of unreacted CFDA SE into the complete cell culture medium. Centrifuge at 1000 rpm for 5 minutes at room temperature to remove the supernatant and complete the final wash.(7) Subsequently, the cells can be cultured using the normal cultivation method. The labeling effect can be directly observed under a fluorescence microscope, or cell proliferation can be detected by flow cytometry after appropriate cultivation time, showing green fluorescence. The labeled cells can also be used for transplantation in live animals and for fluorescence tracing.Note: a If cell fixation is required, use aldehyde fixatives such as 4% paraformaldehyde to fix at room temperature for 15 minutes; If additional labeling such as antibody labeling is required afterwards, please permeabilize the cells with ice acetone for 10 minutes. b. The optimal labeling concentration and incubation time for CFDA SE vary for different cells. The initial experiment can be conducted according to the experimental steps. If the effect is not satisfactory, it is recommended to adjust the staining concentration and incubation time to achieve the best labeling effect.Scope of application：Cell proliferation assay... Read More | This kit is used to extract miRNAs from various animal tissues, plant tissues and cells. The extracted miRNA molecule is complete and high purity, which is suitable for various molecular biology experiments such as Northern blot, real timepcr, miRNA microarray chip, in situ hybridization, This kit is used to extract miRNAs from various animal tissues, plant tissues and cells. The extracted miRNA molecule is complete and high purity, which is suitable for various molecular biology experiments such as Northern blot, real timepcr, miRNA microarray chip, in situ hybridization, RNase protection assay, etcComposition:Scope of application：Nucleic acid extraction and purificationInstruction：1.Experimental preparation：1.1.All reagents were prepared with DEPC-treated solvents. Please use RNase-free tip and centrifuge tube to avoid RNA degradation by RNase during extraction.1.2.70 % ethanol, -20C pre-cooling.2.Operational procedure：There is a slight difference in the operation of miRNA extraction from different samples. The specific steps are as follows :【 Extraction of miRNA from animal tissues】1.Take 20-40 mg tissue, transfer to a pre-cooled mortar, and add liquid nitrogen to grind into powder.Please click below to describe the amount of organization used :①RNA-rich tissue ( e.g. liver ) : no more than 30 mg②Tissues with low RNA content ( e.g., muscle ) : no more than 100 mg③When the amount of tissue used was less than 20 mg : the amount of R-I, R-II and isopropanol used was halved.④When the amount of tissue used was more than 40 mg : the use of R-I, R-II and isopropanol increased proportionally.2.Add 400 ul Buffer R-I, repeatedly aspirate 8-10 times with a syringe equipped with a 21-25 needle, and transfer to a 1.5 m : centrifuge tube ( provided in the kit ). 3.Add 150 µl BufferR-1l, swirl for 15-30 s, centrifuge at 12,000 X g for 5 min. [ Centrifugation at 4 °C is recommended ] 4.Take the supernatant to 1.5ml centrifuge tube, add 180 u anhydrous ethanol, mix evenly.5.The preparation tube was placed in a 2 m : centrifuge tube ( provided in the kit ), the mixture in step 4 was transferred to the preparation tube, and 12,000 X g was centrifuged for 1 min. [ 1 Centrifugation at 4 °C is recommended ; 2 miRNA in the filtrate, pay attention to preserve the filtrate. ]6.Abandon the preparation tube, add 500µl isopropanol to the filtrate, and mix evenly.7.12,000Xg centrifuged for 10 min, discard the supernatant.8.Add 700µl 70 % ethanol ( pre-cooled at -20 °C ), centrifuged at 12,000Xg for 5min.9.The supernatant was discarded and dried at room temperature for 5-10 min.10.70 ul Buffer TE ( nucdease-free ) or RNase-free water was added to the centrifuge tube to elute miRNA.【 Extraction of miRNA from plant tissue 】1.Take 30-150 mg tissue, transfer to a pre-cooled mortar, and add liquid nitrogen to grind into powder.Please click below to describe the amount of organization used :①Plant leaves : usually 10-80 mg② Plant fiber tissue : usually 100-150 mg③When the amount of plant leaf tissue was less than 30 mg : the amount of R-I, R-II and isopropyl alcohol used was halved.④When the amount of plant leaf tissue was more than 80 mg : the use of R-I, R-II and isopropanol increased proportionally.⑤When the amount of plant fiber tissue was more than 150 mg : the use of R-I, R-II and isopropanol increased proportionally.2.Add 400 ul BufferR-I, use a syringe with a 21-25 needle to repeatedly suck 8-10 times, and transfer to a 1.5mI centrifuge tube ( provided in the kit ). 3.Add 150 ul Buffer R-1I, vortex oscillation 15-30 s, 12.000 x g centrifugation 5 min. [ Centrifugation at 4 °C is recommended ]4.Take the supernatant to 1.5ml centrifuge tube, add 180 mountain anhydrous ethanol, mix evenly.The preparation tube was placed in a 2 mI centrifuge tube ( provided in the kit ), the mixture in step 4 was transferred to the preparation tube, and 12.000 xg was centrifuged for 1 min. It is recommended to centrifuge at 4 °C ; 2 miRNA in the filtrate, pay attention to preserve the filtrate. ]Abandon the preparation tube, add 500µl isopropanol to the filtrate, and mix evenly.7.12,000xg high heart for 10 min, discard the supernatant.8.Add 700 ul 70 % ethanol ( -20 °C precooling ), 12,000 xg centrifuge for 5 min.9.The supernatant was discarded and dried at room temperature for 5-10 min.10.70 ul Buffer TE ( nucdease-free ) or RNase-free water was added to the centrifuge tube to elute miRNA.【miRNA extraction from cells】Steps 1-3 According to the different ways of cell culture, two experimental methods, a or b, can be selected.a. Suspension cultured animal cells or cell suspension obtained from petri dishes or culture flasks or freshly isolated animal tissue single cell suspension :1a.Collect 2X 10 * -1X 10 ' cells, centrifuge 2,000Xg for 5 min, discard the supernatant ;2a. Add 400 µl Buffer R-I, repeatedly draw 8-10 times with a syringe containing 21-25 needles, and transfer to a 1.5 mI centrifuge tube ( provided in the kit ) ;3a. Add 150µl Buffer R1I, vortex oscillation 15-30s, 12.000Xg centrifugal 5min. [ build at 4 °C centrifugal ].b. Cells cultured on 96-well L, 24-well, 12-well or 6-well plates :Cells were collected from 96-well, 24-well, 12-well or 6-well culture plates, and the medium was discarded as much as possible, and 400 u / well Buffer R-I was added to each well, and the pipette gun was used to blow up and down 8-10 times ;2b.Transfer the above cell suspension to a 1.5ml centrifuge tube ( provided in the kit ), and repeatedly draw 8-10 times with a syringe containing 21-25 needles ;3b. Add 150 µl Bufflr R-II, swirl for 15-30 s, centrifuge for 5 min at 12,000 × g. [ Recommended at 4 °C ]4.Take the supernatant to 1.5ml centrifuge tube, add 180 mountain anhydrous ethanol, mixing evenly.5.The preparation tube was placed in a 2 ml centrifuge tube ( provided in the kit ), the mixture in step 4 was transferred to the preparation tube, and centrifuged at 12.000 Xg for 1 min. [ 1 Centrifugation at 4 °C is recommended ; 2 miRNA in the filtrate, pay attention to preserve the filtrate. ]6.Abandon the preparation tube, add 500 u of isopropanol to the filtrate, and mix evenly.7.12,000Xg high heart for 10 min, discard the supernatant.8.Add 700µ70 % ethanol ( pre-cooled at − 20 °C ), centrifuged at 12,000 × g for 5 min.9.Abandon the supernatant, dry at room temperature for 5 - 10 min.10.70 ul Bufer TE ( nucdease-free ) or RNase-free water was added to the centrifuge tube to elute mRNA.3.Flow chartMatters needing attention：Buffer R-I contains irritating compounds, when operating to wear latex gloves and glasses, to avoid contamination of the skin, eyes and clothes, be careful not to inhale the nose and mouth. If the skin, eyes, to immediately rinse with a lot of water or saline, if necessary, seek medical advice... Read More | This reagent kit uses highly sensitive silver dye, which can be applied to protein staining of denatured and non denatured gels. It has the advantages of clear target bands, low background, and flexible control of operation time. In addition, this reagent kit has added a short-term sensitization This reagent kit uses highly sensitive silver dye, which can be applied to protein staining of denatured and non denatured gels. It has the advantages of clear target bands, low background, and flexible control of operation time. In addition, this reagent kit has added a short-term sensitization step, which can significantly reduce the background and enhance the brightness of the target band. P665901Component20 TStorageP665901ASilver Stain Sensitizer (500×)2×1 mLRTP665901BSilver Stain Enhancer3 mLRTP665901CSilver Stain2×250 mLRTP665901DSilver Stain Developer4×125 mLRT Matters needing attention1. Please prepare 50 ml of fixed solution (ultrapure water: ethanol: acetic acid=6:3:1), 50 ml of eluent (10% ethanol), and 50 ml of termination solution (5% acetic acid) in advance.2. Please use deionized water and clean glass or plastic containers during operation, and wear disposable gloves for operation.The entire silver dyeing process needs to be carried out on a shaker, with a rotation speed of about 60 rpm.4. Self prepared ethanol and glacial acetic acid are required.Instructions for useThe dosage of each solution in the following operation steps takes the gel with a size of 8.5 × 5.5 cm and a thickness of 1.0 mm as an example. The gel is immersed in the solution completely, and is operated on a shaker, with a general dosage of 25 ml. For large gel, the dosage of each solution should be scaled up according to the gel volume. Please prepare 50 ml of fixed solution (ultrapure water: ethanol: glacial acetic acid=6:3:1), 50 ml of eluent (10% ethanol), and 50 ml of termination solution (5% glacial acetic acid) in advance.1. Water washing: After electrophoresis is completed, wash the gel twice with ultrapure water for 5 minutes each time.2. Fixation: Fix the gel twice with 25 ml of fixative solution for 15 minutes each time.3. Elution: Wash the adhesive twice with eluent, each time for 5 minutes.4. Water washing: Wash the glue twice with ultrapure water, each time for 5 minutes.5. Sensitization: put the gel washed in the previous step into the silver dye sensitization working solution, incubate it accurately for 1 minute at room temperature, and then wash it with ultrapure water for three times, each time for 20 seconds. Preparation of silver staining sensitization working solution: Take 50 µ l Silver Stain Sensitivity (500 x) and add it to 25 ml of ultrapure water, mix well.6. Silver staining: discard ultrapure water and incubate gel in silver staining working solution for 30 minutes. Preparation of silver staining working solution: Take 25ml Silver Stain and add 50 µ l Silver Stain Enhanced to mix well.7. Water washing: Quickly wash the glue twice with ultrapure water, with each washing accurately controlled for 20 seconds.8. Development: Immerse the washed gel in the developer immediately and incubate it at room temperature for 2-3 minutes until the protein strip is clear. Preparation of developer: Take 25ml Silver Stain Developer and add 30 µ l Silver Stain Enhanced to mix well. Attention: Within 30 seconds of development, protein bands begin to appear and continue to develop for 2-3 minutes. If the protein band appears lighter, the development time can be appropriately extended to 5 minutes or more.9. Termination: After washing the developer on the gel with the termination solution, soak the gel in a new termination solution to react for 10 minutes.Experimental imagesSilver staining results of BSA protein samples after 10% SDS-PAGE gel electrophoresisThe molecular weight of BSA protein is about 66 kD, and the loading amounts from left to right are 50 ng, 10 ng, and 5 ng, respectively... Read More |