| Description | Low-Density Lipoprotein (LDL) in plasma is the main carrier of endogenous cholesterol. It is degraded and metabolized by binding to the LDL receptor (LDL-R) on cell membranes and serves as the primary vehicle for transporting cholesterol to peripheral tissues. However, when LDL, especially oxidized Low-Density Lipoprotein (LDL) in plasma is the main carrier of endogenous cholesterol. It is degraded and metabolized by binding to the LDL receptor (LDL-R) on cell membranes and serves as the primary vehicle for transporting cholesterol to peripheral tissues. However, when LDL, especially oxidized LDL (OX-LDL), is present in excess, the cholesterol it carries accumulates in the arterial walls, increasing the risk of atherosclerosis. Atherosclerosis is the pathological basis and risk factor for the majority of cardiovascular and cerebrovascular diseases.Detection Principle: In a cholesterol assay system containing cholesterol esterase (CHER) and cholesterol oxidase (CHOD), specific surfactants are added to selectively solubilize LDL-C for the determination of LDL-cholesterol. Other lipoproteins (HDL, VLDL, chylomicrons) do not react due to inhibition by the surfactants and sugar compounds, remaining in the form of lipoproteins in the reaction mixture. Based on this principle, LDL-cholesterol can be measured directly. Subsequently, esterase catalyzes the hydrolysis of cholesterol esters to generate Free Cholesterol (FC). FC is oxidized by cholesterol oxidase to produce 4-cholestenone and hydrogen peroxide. Hydrogen peroxide then reacts with 4-aminoantipyrine and other components to produce a red quinoneimine compound, which has a characteristic absorption peak at 546 nm. The LDL-C content is determined by measuring the absorbance at 546 nm.Component96TStorageReagent 118 mL2-8℃. Store in the dark.Reagent 26 mL2-8℃. Store in the dark.Standard1EA2-8℃. Store in the dark.Standard (Powder, 1 vial) Preparation:1. Before use, centrifuge at 8000 g, 4°C for 2 minutes to collect the powder at the bottom of the tube.2. Add 0.1 mL of distilled water to dissolve. Use within one week. The prepared concentration is as indicated on the label.User-Prepared Instruments and Reagents:Mortar (Homogenizer), balance, ice box (ice maker), benchtop centrifuge, adjustable micropipettes, water bath (oven, incubator, metal bath), 96-well plate, centrifuge tubes, microplate reader, distilled water (deionized water or ultrapure water are acceptable), ethanol.Experimental ProcedureIt is recommended to first perform a preliminary test using 1-3 samples with expected significant differences (e.g., different types or groups) to familiarize yourself with the procedure and to determine or adjust sample concentrations based on the preliminary results, preventing unnecessary waste of samples or reagents.1. Sample Extraction1.1 Tissue SamplesWeigh approximately 0.1 g of tissue sample and place it in a mortar. Add 1 mL of ethanol and homogenize in an ice bath. Centrifuge at 12,000 rpm, 4°C or room temperature for 10 minutes. Collect the supernatant for assay.Note: If increasing the sample amount, maintain a tissue mass (g) to ethanol volume (mL) ratio between 1:5 and 1:10.1.2 Liquid SamplesAssay clear liquid samples directly. If turbid, centrifuge and use the supernatant for assay.1.3 Bacterial/Cell SamplesCollect bacteria or cells into a centrifuge tube, centrifuge, and discard the supernatant. Add 1 mL of ethanol per approximately 5 million bacteria/cells. Disrupt the bacteria or cells by sonication in an ice bath (power 200W, pulse 3s on, 10s off, repeat 30 times). Centrifuge at 12,000 rpm, 4°C for 10 minutes. Collect the supernatant and keep it on ice for assay.*Note: If increasing the sample amount, maintain a bacteria/cell count (10⁴) to ethanol volume (mL) ratio between 500:1 and 1000:1.*2. Assay Steps2.1 Preheat the microplate reader for 30 minutes (or wait for the instrument to complete its self-check). Set the wavelength to 546 nm.2.2 Thaw all reagents to room temperature (25°C). Add reagents sequentially to a 96-well plate as follows:Reagent (µL)Test TubeStandard Tube (once)Blank Tube (once)Sample2.5Standard2.5Distilled Water2.5Reagent 1180180180Mix well and incubate at 37°C for 5 minutes. Read the absorbance at 546 nm for each tube (A1 ).Reagent 2606060Mix well and incubate at 37°C for 10 minutes. Read the absorbance at 546 nm for each tube (A2 ). Calculate ΔA = A2 - A1 for each tube.Note:(1) If the A2 value for the Test Tube is greater than 1, dilute the sample with ethanol. The dilution factor (D) must be substituted into the calculation formula.(2) If ΔA for the Test Tube is lower than ΔA for the Blank Tube, consider increasing the sample volume V1 (e.g., increase the sample volume in the Test Tube and the water volume in the Blank Tube to 5 µL or more, keeping Reagents 1 and 2 volumes unchanged; for the Standard Tube, keep at 2.5 µL and add 2.5 µL distilled water to make up volume) or increasing the sample weight W (e.g., to 0.2 g or more). The changed V1 or W must then be substituted into the calculation formula.3. Calculation of Results3.1 Based on Sample MassDerived Formula:LDL-C (µmol/g weight) = (CStandard × V2 ) × (ΔATest - ΔABlank ) ÷ (ΔAStandard - ΔABlank ) ÷ (W × V1 ÷ V) × DSimplified Formula:LDL-C (µmol/g weight) = CStandard × (ΔATest - ΔABlank ) ÷ (ΔAStandard - ΔABlank ) ÷ W × D3.2 Based on Protein ContentDerived Formula:LDL-C (µmol/mg prot) = (CStandard × V2 ) × (ΔATest - ΔABlank ) ÷ (ΔAStandard - ΔABlank ) ÷ (Cpr × V1 ÷ V) × DSimplified Formula:LDL-C (µmol/mg prot) = CStandard × (ΔATest - ΔABlank ) ÷ (ΔAStandard - ΔABlank ) ÷ Cpr × D3.3 LDL-C Content in LiquidsDerived Formula:LDL-C (mmol/L) = (CStandard × V2 ) × (ΔATest - ΔABlank ) ÷ (ΔAStandard - ΔABlank ) ÷ V1 × DSimplified Formula:LDL-C (mmol/L) = CStandard × (ΔATest - ΔABlank ) ÷ (ΔAStandard - ΔABlank ) × D3.4 Based on Cell CountDerived Formula:LDL-C (nmol/10⁴ cells) = (CStandard × V2 ) × 10³ × (ΔATest - ΔABlank ) ÷ (ΔAStandard - ΔABlank ) ÷ (500 × V1 ÷ V) × DSimplified Formula:LDL-C (nmol/10⁴ cells) = 2 × CStandard × (ΔATest - ΔABlank ) ÷ (ΔAStandard - ΔABlank ) × DParameter Definitions:CStandard : Concentration as indicated on the label (mmol/L or µmol/mL)V1 : Volume of sample added (0.0025 mL)V: Volume of extraction buffer (ethanol) added (1 mL)V2 : Volume of standard added (0.0025 mL)D: Dilution factor (1 if not diluted)500: Number of cells (in units of 10⁴)W: Sample weight (g)Cpr: Protein concentration of the supernatant (mg/mL); Aladdin's BCA Protein Quantification Kit (B665595) or Ready-to-Use BCA Protein Quantification Kit (R1491648) is recommended.Precautions1. It is recommended to first perform a preliminary test using 1-3 samples with expected significant differences (e.g., different types or groups) to familiarize yourself with the procedure. Based on the preliminary results, determine or adjust sample concentrations to prevent unnecessary waste of samples or reagents.2. This product is for research use only. Not for use in clinical diagnosis. For your safety and health, please wear a lab coat and disposable gloves during operation... Read More | D-Lactate, typically present in the bloodstream at nanomolar concentrations, is produced by an intestinal source or via the methylglyoxal pathway. In mammals, D-Lactate metabolism requires D-Lactate hydrogenase and is metabolized slowly, thus an increase in blood concentration levels can lead to D-Lactate, typically present in the bloodstream at nanomolar concentrations, is produced by an intestinal source or via the methylglyoxal pathway. In mammals, D-Lactate metabolism requires D-Lactate hydrogenase and is metabolized slowly, thus an increase in blood concentration levels can lead to acidemia and acidosis. The severity of this D-lactic acidosis can be associated with neurotoxic symptoms. Significant D-Lactate accumulations in the body can also be related to impaired metabolism and excretion.D-Lactate Colorimetric Assay kit has been used to determine the stereospecificity of lactate produced.Suitability: Suitable for use with samples of serum, plasma, cells, culture and fermentation media.Principle: In this assay, D-Lactate is specifically oxidized by D-Lactate hydrogenase and generates a proportional colorimetric product measured at 450 nm. The useful concentration range in samples is 0.1-10 mM D-Lactate... Read More | DescriptionProvides an inert environment to run oxygen sensitive cross-coupling reactions in a laboratory fume hood.Designed to be used with KitAlysis High-Throughput Screening Kits and KitAlysis 24-Well Reaction Block | Product content: M665794Component125 TStorageM665794A2×miRNA qPCR Mixture (ROX)2×750 µL-20℃. Avoid freeze/thaw cycleM665794BReverse Primer, 10 µM60 µL-20℃. Avoid freeze/thaw cycleM665794CddH2O1.5 mL-20℃. Avoid freeze/thaw cycle Product Introduction:This kitProduct content: M665794Component125 TStorageM665794A2×miRNA qPCR Mixture (ROX)2×750 µL-20℃. Avoid freeze/thaw cycleM665794BReverse Primer, 10 µM60 µL-20℃. Avoid freeze/thaw cycleM665794CddH2O1.5 mL-20℃. Avoid freeze/thaw cycle Product Introduction:This kit uses the principle of SYBR Green I chimeric fluorescent dye method for miRNA fluorescence quantitative PCR detection. The kit includes 2 x miRNA qPCR Mixture and Reverse Primer required for detection. 2 x miRNA qPCR Mixture is a new generation pre mixed form of fluorescence quantitative PCR detection reagent specially developed for miRNA quantitative detection. The fluorescent dye SYBR Green I contained in it can bind to all double stranded DNA, making the product suitable for detecting different target sequences without the need to synthesize specific labeled probes. The GoldStar Taq DNA polymerase is a chemically modified and highly efficient thermal starter enzyme, coupled with a unique buffer system, which enhances reaction specificity, sensitivity, and enables accurate quantification of miRNA over a wider range. The 2x miRNA qPCR Mixture contains ROX dye and is suitable for fluorescence quantitative PCR instruments that require ROX as a calibration dye.Note: This kit must be used in conjunction with the miRNA cDNA first strand synthesis kit.Self prepared experimental materials: qPCR upstream primer.Forward Primer design principles:1. Follow the most common principles of primer design.2.Based on mature miRNA sequences, replacing U with T is the most basic and simplest design method.3.The Tm value of the downstream primer provided in the reagent kit is 63.6 ℃, and the Tm value of the upstream primer should be designed to be around 63.6 ℃ as much as possible.4. If the Tm value of the primer directly designed according to principle "2" is too low, several bases (preferably G or C bases) can be added to the 5 'end of the primer; One or several A bases can also be added at the 3 'end; Alternatively, both the 5 'and 3' ends can be modified simultaneously.5.If the Tm value of a primer designed directly according to principle "2" is too high, several bases can be removed from the 5 'or 3' end of the primer.Notes:1. Before using the reagent, please gently mix it upside down to avoid foaming, and use it after a brief centrifugation.2. The amount of miRNA first strand cDNA added should not exceed 10% of the volume of Real time PCR.3. For special detection systems, high content of cDNA templates can easily lead to non-specific amplification. Dilute cDNA appropriately (10 or 100 times dilution) based on the abundance of detected miRNAs.4. The 2x miRNA qPCR Mixture in this product contains SYBR Green I and ROX dyes. When storing this product or preparing PCR reaction solution, strong light exposure should be avoided.5. Avoid repeated freezing and thawing of this product. Repeated freezing and thawing may cause a decrease in product performance. This product can be stored at -20 ℃ for long-term storage. If frequent use is required in the short term, the 2xmiRNA qPCR Mixture can be stored at 2-8 ℃. However, the Reverse primer still needs to be stored at -20 ℃.Operation steps:1. Melt 2 x miRNA qPCR Mixture and Reverse Primer at room temperature (10 µ M). 2. When using, please gently mix the 2x miRNA qPCR Mixture upside down to avoid foaming, and use after brief centrifugation. If the reagent is not well mixed, its reaction performance will decrease.3. Place the reagent on ice and prepare the reaction system according to the following table: reagent volume final concentration 2×miRNA qPCR Mixture（ROX） 10 µl 1× Forward primer（10 µM） 0.4µl 0.2 µM Reverse primer（10 µM） 0.4µl 0.2 µM MiRNA first strand cDNA X µl — ddH2O up to 20 µl —4. The reaction program is set as follows:Attention!The pre denaturation reaction of this product must be completed at 95 ℃ for 10 minutes! Note: 1) The hot start enzyme used in this product must be activated under pre denaturation conditions of 95 ℃ and 10 minutes.2) The annealing temperature should be set at 60-64 ℃ as a reference range. When non-specific reactions occur, the annealing temperature can be increased... Read More | Product content： Component S665549 50 preps Buffer SW 60 ml Buffer SL 60 ml Buffer GL 50 ml Buffer GW1（concentrate） 2X13 ml Buffer GW2（concentrate） 15 ml Buffer GE 15 ml Spin Columns DM 50 with Collection Tubes 50Product IntroductionThis kit is suitable for Product content： Component S665549 50 preps Buffer SW 60 ml Buffer SL 60 ml Buffer GL 50 ml Buffer GW1（concentrate） 2X13 ml Buffer GW2（concentrate） 15 ml Buffer GE 15 ml Spin Columns DM 50 with Collection Tubes 50Product IntroductionThis kit is suitable for extracting total DNA from fecal samples, including the total DNA of cells, bacteria, parasites, and viruses in the samples, as well as samples containing high concentrations of PCR reaction inhibitors. This product can process up to 300 mg of fecal samples and purify to obtain mainly 20-30 kb DNA fragments. The purification process does not require toxic solvents such as phenol or chloroform, and does not require ethanol precipitation. High purity DNA can be obtained within one hour. This reagent kit adopts a unique buffering system to efficiently bind DNA from the lysis solution to the adsorption column. At the same time, protein impurities and other organic compounds that inhibit downstream reactions in feces can flow through the membrane. Inhibitors of PCR and enzyme reactions, as well as residual impurities, can be effectively removed through two washing steps. Finally, high-purity DNA can be obtained by washing with low salt buffer or water. The purified DNA can be directly used for downstream experiments such as enzyme digestion, PCR, Real Time PCR, library construction, Southern Blot, and molecular labeling.Preparation and important precautions before the experiment1. Samples should avoid repeated freeze-thaw cycles, otherwise it may result in smaller extracted DNA fragments and a decrease in extraction volume.2.Before the first use, anhydrous ethanol should be added to Buffer GW1 and GW2 according to the instructions on the reagent bottle label.3. Before use, please check whether there is crystallization or precipitation in Buffer SL and Buffer GL. If there is crystallization or precipitation, please dissolve Buffer SL and Buffer GL again in a 56 ℃ water bath.4. If downstream experiments are sensitive to RNA contamination, 4 can be added after adding Buffer SL µ RNase A of DNase Free (100 mg/ml) is not provided in this kit. If needed, it can be ordered separately from our company, item number: S665549Operation steps1. Take a fecal sample of 100-300 mg and place it in a centrifuge tube (provided by oneself).2. Add 1 ml of Buffer SW and vortex for 3-5 minutes to evenly disperse the sample in the solution. Centrifuge at 12000 rpm (~13400 × g) for 1 minute and discard the supernatant.3. Add 1 ml of Buffer SL and vortex for 3-5 minutes to evenly disperse the sample in the solution. Take a water bath at 65 ℃ for 20 minutes and vortex for 15 seconds every 5 minutes. Note: To remove RNA, add 4 after completing the above steps µ RNase A solution (product number: CW0601S) with a concentration of 100 mg/ml, shake well and let stand at room temperature for 5-10 minutes.4.Centrifuge at 2000 rpm for 3 minutes and transfer the supernatant to a new centrifuge tube (provided by oneself).5. Add an equal volume of Buffer GL to the supernatant, invert and mix 15-25 times, and leave on ice for 5 minutes. Centrifuge at 12000 rpm for 5 minutes. Attention: At this time, the liquid may be in a transparent or turbid state, which does not affect the experiment. 6. Add the supernatant obtained in step 5 to the spin columns DM that have been loaded into the collection tube. If the solution cannot be added at once, it can be transferred multiple times. Centrifuge at 12000 rpm (~13400 × g) for 1 minute, discard the waste liquid in the collection tube, and place the adsorption column back into the collection tube.7. Add 500 to the adsorption column µ Buffer GW1 (check if anhydrous ethanol has been added before use), centrifuge at 12000 rpm for 1 minute, discard the waste liquid in the collection tube, and place the adsorption column back into the collection tube. 8. Repeat step 7.9. Add 500 to the adsorption column µ Buffer GW2 (check if anhydrous ethanol has been added before use), centrifuge at 12000 rpm for 1 minute, discard the waste liquid in the collection tube, and place the adsorption column back into the collection tube.10.12000 rpm for 2 minutes and discard the waste liquid from the collection tube. Place the adsorption column at room temperature for a few minutes to thoroughly air dry. Note: The purpose of this step is to remove residual ethanol from the adsorption column, which can affect subsequent enzymatic reactions (such as enzyme digestion, PCR, etc.).11. Place the adsorption column in a new centrifuge tube (self provided) and add 50-100 drops of suspended droplets to the middle of the adsorption column µ L Buffer GE or sterilized water, leave at room temperature for 2-5 minutes, centrifuge at 12000 rpm for 1 minute, collect DNA solution, and store DNA at -20 ℃.Note: 1) If downstream experiments are sensitive to pH or EDTA, they can be washed off with sterilized water. The pH value of the eluent has a significant impact on the elution efficiency. If water is used as the eluent, its pH value should be ensured to be between 7.0-8.5 (NaOH can be used to adjust the pH value of the water to this range). When the pH value is below 7.0, the elution efficiency will be reduced2) Incubating at room temperature for 5 minutes before centrifugation can increase yield.3) Use an additional 50-100 µ Further washing with buffer GE or sterilized water can increase yield.4) If you want to increase the final concentration of DNA, you can add the DNA eluent obtained in step 11 back onto the adsorption membrane and repeat step 11; It is possible to increase the final concentration of DNA, but it may reduce the total yield. If the amount of DNA is less than 1 µ g. Recommended 50 µ Wash with buffer GE or sterilized water.5) DNA stored in water can be affected by acidic hydrolysis. If long-term storage is required, it is recommended to elute with Buffer GE and store at -20 ℃.6) The residual trace PCR inhibitors in the genomic DNA template may have adverse effects on the PCR reaction, which can be solved by diluting DNA by 2-10 times... Read More |