| Description | Reducing sugars (RS) are widely present in animals, plants, microorganisms, and cultured cells. Reducing sugars in plants primarily include glucose, fructose, and maltose. Among these, glucose and fructose are not only the main substrates for respiration but also serve as substrates for the further Reducing sugars (RS) are widely present in animals, plants, microorganisms, and cultured cells. Reducing sugars in plants primarily include glucose, fructose, and maltose. Among these, glucose and fructose are not only the main substrates for respiration but also serve as substrates for the further synthesis of sucrose, starch, and cellulose.Detection Principle: In an alkaline solution, 3,5-dinitrosalicylic acid (DNS) can be reduced by reducing sugars to produce a brown-red-colored amino compound, which has a characteristic absorption peak at 540 nm. Within a certain concentration range, the RS content is linearly correlated with the absorbance at 540 nm. The RS content in the sample can be calculated based on a standard curve.Detection Range: 0.05 - 0.6 mg/mLSensitivity: 0.025 mg/mLApplicable Samples: Plant tissues, animal tissues, cells, bacteria, serum (plasma)R1501790Component48T96TStorageR1501790AExtraction Buffer60 mL120 mL2-8℃R1501790BDNS Reagent10 mL20 mL2-8℃. Store in the dark.R1501790CStandard1EA1EA2-8℃Note: Before formal testing, it is recommended to perform a preliminary test with 2-3 samples expected to have significant differences.User-Prepared Instruments and ReagentsMicroplate reader or visible spectrophotometer (capable of measuring absorbance at 540 nm)96-well plate or micro glass cuvettes, adjustable micropipettes and tipsCentrifuge, water bathDeionized waterHomogenizer (for tissue samples)Experimental Procedure1. Reagent PreparationReagent NameReagent PreparationNotesExtraction BufferReady-to-use; Equilibrate to room temperature before use.Store at 4°C. Slightly irritating. Use appropriate personal protective equipment.DNS ReagentReady-to-use; Equilibrate to room temperature before use.Store at 4°C protected from light. Slightly irritating. Use appropriate personal protective equipment.StandardBefore use, add 1 mL of deionized water to dissolve, preparing a 10 mg/mL stock standard solution.Can be stored at 4°C for 2 weeks.2. Standard Curve SetupDilute the 10 mg/mL standard stock solution with deionized water to concentrations of 0.6, 0.5, 0.4, 0.3, 0.2, 0.1, and 0.05 mg/mL.TubeVolume of 10 mg/mL Standard (µL)Volume of Deionized Water (µL)Concentration (mg/mL)Std.1609400.6Std.2509500.5Std.3409600.4Std.4309700.3Std.5209800.2Std.6109900.1Std.759950.05Note: The standard curve must be generated with each experiment. Diluted standard solutions are unstable and must be used within 4 hours.3. Sample Preparation3.1 Plant or Animal Tissue SamplesWeigh approximately 0.1 g of tissue. Add 1 mL of Extraction Buffer and homogenize in an ice bath. Transfer the homogenate to a capped centrifuge tube (to prevent evaporation during heating). Incubate in an 80°C water bath for 40 minutes, vortexing every 5 minutes. Centrifuge at 8,000 g, 25°C for 10 minutes. Collect the supernatant for assay.3.2 Bacteria or CellsCollect bacteria or cells into a centrifuge tube; discard the supernatant. Add 1 mL of Extraction Buffer per 5 million bacteria/cells. Sonicate in an ice bath for 5 minutes (power 20%, pulse 3s on, 10s off, repeat 30 times). Transfer to a capped centrifuge tube (to prevent evaporation during heating). Incubate in an 80°C water bath for 40 minutes, vortexing every 5 minutes. Centrifuge at 8,000 g, 25°C for 10 minutes. Collect the supernatant for assay.3.3 Serum (Plasma) SamplesTake 0.1 mL of serum (plasma) and add 0.9 mL of Extraction Buffer; mix thoroughly. Transfer to a capped centrifuge tube (to prevent evaporation during heating). Incubate in an 80°C water bath for 40 minutes, vortexing every 5 minutes. Centrifuge at 8,000 g, 25°C for 10 minutes. Collect the supernatant for assay.Note:If protein concentration measurement is required, Aladdin's BCA Protein Quantification Kit (B665595) or Ready-to-Use BCA Protein Quantification Kit (R1491648) is recommended. The Extraction Buffer contains components that denature proteins. If calculating based on protein concentration, protein needs to be re-extracted separately for measurement.4. Assay Steps4.1 Preheat the microplate reader or visible spectrophotometer for at least 30 minutes. Set the wavelength to 540 nm. For spectrophotometers, zero the instrument with deionized water.4.2 Assay Procedure:ReagentBlank Tube (µL)Standard Tube (µL)Test Tube (µL)Control Tube (µL)Sample00175175Standard (various conc.)017500Deionized Water17500125DNS Reagent1251251250Mix well. Heat in a boiling water bath for 5 minutes (cap tightly to prevent evaporation). Remove and immediately cool to room temperature. Transfer 200 µL to a 96-well plate or micro glass cuvette. Measure the absorbance at 540 nm. Calculate ΔA test = A test - A control, ΔA standard = A standard - A blank. Note:The Blank and Standard tubes only need to be set up 1-2 times.It is recommended to perform a preliminary test with 2-3 samples expected to have significant differences before the formal experiment. If ΔA <sub> test </sub> is less than 0.04, consider increasing the sample volume appropriately. If ΔA <sub> test </sub> is greater than the ΔA <sub> standard </sub> of the 0.6 mg/mL standard, further dilute the sample with Extraction Buffer (multiply the result by the dilution factor) or reduce the amount of sample used for extraction.5. Calculation of ResultsNote: We provide both the derived formula and a simplified formula. They are equivalent. It is recommended to use the simplified formula in bold for final calculation.5.1 Standard Curve PlottingPlot the standard concentration (y-axis) against ΔA standard (x-axis) to generate the standard curve. Substitute ΔA test into the standard curve equation to calculate y (mg/mL).5.2 Sample Reducing Sugar Content Calculation(1) Based on Sample WeightReducing Sugar (µg/g) = 1000 × y × V<sub>extraction</sub> ÷ W × n = 1000 × y / W × n(2) Based on Sample Protein ConcentrationReducing Sugar (µg/mg prot) =1000 × y × Vextraction ÷ (Vextraction × Cpr) × n=1000 × y / Cpr × n(3) Based on Bacterial or Cell CountReducing Sugar (µg/10⁴) =1000 × y × V<sub>extraction</sub> ÷ 500 × n = 2 × y × n(4) Based on Serum (Plasma) VolumeReducing Sugar (µg/mL) = 1000 × y × Vextraction ÷ Vliquid × n = 10000 × y × nParameter Definitions:1000: Unit conversion factor (1 mg/mL = 1000 µg/mL)V extraction : Volume of Extraction Buffer added (1 mL)V liquid : Volume of serum (plasma) added (0.1 mL)Cpr: Sample protein concentration (mg/mL)W: Sample weight (g)500: Total number of bacteria or cells (5 million)n: Dilution factor6. Representative ResultsTypical Standard Curve: y = 0.2243x + 0.0545, R² = 0.9957 PrecautionsThis product is for research use only. Not for use in clinical diagnosis. For your safety and health, please wear lab coats and disposable gloves during operation... Read More | Inquire | Inquire | Product content: M665559Component50 TStorageM665559ABuffer GTT15 mLRTM665559BBuffer GL15 mLRTM665559CBuffer GW1（concentrate）13 mLRTM665559DBuffer GW2（concentrate）15 mLRTM665559EBuffer GE15 mLRTM665559FProteinase K1.25 mLRTM665559GSpin CoLumns DM with CoLLection Tubes50 Product content: M665559Component50 TStorageM665559ABuffer GTT15 mLRTM665559BBuffer GL15 mLRTM665559CBuffer GW1（concentrate）13 mLRTM665559DBuffer GW2（concentrate）15 mLRTM665559EBuffer GE15 mLRTM665559FProteinase K1.25 mLRTM665559GSpin CoLumns DM with CoLLection Tubes50 EART Product Introduction:This reagent kit is suitable for extracting high-purity total DNA from fresh or frozen mouse or rat tails. The method provided by this reagent kit is simple and feasible, and the purification process does not require phenol or chloroform extraction. It can obtain DNA fragments up to 50 kb, and can also effectively recover fragments of 100 bp. This reagent kit uses a unique lysis solution to effectively lyse mouse tail samples. The optimized buffer system efficiently binds the DNA generated after the lysis of mouse tail to the silica matrix adsorption column, while other pollutants can flow through the membrane; Inhibitors of PCR and other enzymatic reactions can be effectively removed through a two-step washing process, followed by washing with low salt buffer or water to obtain high-purity DNA. The purified DNA can be directly used for downstream experiments such as enzyme digestion, PCR, ReaL Time PCR, library construction, Southern BLot, and molecular labeling.Self prepared reagent: anhydrous ethanol.Preparation and important precautions before the experiment:1. Samples should avoid repeated freeze-thaw cycles, otherwise it may result in smaller extracted DNA fragments and a decrease in extraction volume.2.Before the first use, anhydrous ethanol should be added to BufferGW1 and BufferGW2 according to the instructions on the reagent bottle label.3. Before use, please check if there is any crystallization or precipitation in the Buffer GL. If there is any crystallization or precipitation, please dissolve the Buffer GL again in a 56 ℃ water bath.Operation steps:1. Take a tail of a rat or two mice with a length of 0.4-0.6 cm, grind it into fine powder in liquid nitrogen or cut it into pieces and place it in a centrifuge tube (provided by oneself). Join 180 µ L Buffer GTT, shake and mix well. Note: Ensure that the starting quantity of the organization does not exceed the recommended range.2. Add 20 µ L Protein K, vortex oscillation, thoroughly mix.3. Place in a 56 ℃ water bath until the tissue solution is completely clear. Generally, digestion is required for 6-8 hours. During the incubation process, vortex oscillation is required to evenly disperse the sample. Note: 1) If there is still gel like substance after incubation and vortex oscillation, digest overnight or add 20 more if necessary µ L Protein K digestion will not affect subsequent operations. 2) To remove RNA, add 4 after completing the above steps µ L 100 mg/mL RNase A solution, shake well and let stand at room temperature for 5-10 minutes.4.12000 rpm (~13400 × g) for 1 minute to remove undigested tissues similar to mouse hair. Transfer the supernatant to a new centrifuge tube (provided by oneself).5. Add 200 µ L Buffer GL, vortex oscillation, thoroughly mixed. Join 200 µ L anhydrous ethanol, vortex and shake, thoroughly mix. Short centrifugation allows the solution on the tube wall to be collected to the bottom of the tube.Attention: 1) After adding Buffer GL and anhydrous ethanol, immediately vortex and shake to mix well.2) If multiple samples are operated together, Buffer GL and anhydrous ethanol can be mixed in equal proportions and added to the samples together.3) The addition of Buffer GL and anhydrous ethanol may produce white precipitates, which will not affect subsequent experiments.6. Add all the solutions obtained in step 5 to the adsorption column (Spin CoLumins DM) that has been loaded into the collection tube. If the solution cannot be added at once, it can be transferred multiple times. Centrifuge at 12000 rpm for 1 minute, discard the waste liquid in the collection tube, and place the adsorption column back into the collection tube.7. Add 500 to the adsorption column µ L Buffer GW1 (check if anhydrous ethanol has been added before use), centrifuge at 12000 rpm for 1 minute, discard the waste liquid in the collection tube, and place the adsorption column back into the collection tube.8. Add 500 to the adsorption column µ L Buffer GW2 (check if anhydrous ethanol has been added before use), centrifuge at 12000 rpm for 1 minute, discard the waste liquid in the collection tube, and place the adsorption column back into the collection tube.Note: To further improve DNA purity, repeat step 8.9.12000 rpm for 2 minutes and discard the waste liquid from the collection tube. Place the adsorption column at room temperature for a few minutes to thoroughly air dry. Note: The purpose of this step is to remove residual ethanol from the adsorption column, which will affect subsequent enzymatic reactions (such as enzyme digestion, PCR, etc.).10. Place the adsorption column in a new centrifuge tube (provided by oneself) and add 50-200 to the middle of the adsorption column in the air µ L Buffer GE or sterilized water, leave at room temperature for 2-5 minutes, centrifuge at 12000 rpm for 1 minute, collect DNA solution, and store DNA at -20 ℃.Note: 1) If downstream experiments are sensitive to pH or EDTA, they can be washed off with sterilized water. The pH value of the eluent has a significant impact on the elution efficiency. If water is used as the eluent, its pH value should be ensured to be between 7.0-8.5 (NaOH can be used to adjust the pH value of the water to this range). When the pH value is below 7.0, the elution efficiency is not high.2) Incubating at room temperature for 5 minutes before centrifugation can increase yield.3) Use an additional 50-200 µ Re washing with L Buffer GE or sterilized water can increase yield.4) If you want to increase the final concentration of DNA, you can add the DNA eluent obtained in step 10 back onto the adsorption membrane and repeat step 10; If the elution volume is less than 200 µ L. It is possible to increase the final concentration of DNA, but it may reduce the total yield. If the amount of DNA is less than 1 µ g. Recommended 50 µ L Buffer GE or off... Read More | O665690 Component 50T Storage O665690A DNase I 1000 U -20℃.Avoid freeze/thaw cycle. O665690B 10×Reaction Buffer 1000 µL -20℃.Avoid freeze/thaw cycle. O665690C Buffer RLS 40 mL RT O665690D Buffer RW1 40 mL RT O665690E Buffer RW2 (concentrate) 11 mL RT O665690F RNase-Free Water O665690 Component 50T Storage O665690A DNase I 1000 U -20℃.Avoid freeze/thaw cycle. O665690B 10×Reaction Buffer 1000 µL -20℃.Avoid freeze/thaw cycle. O665690C Buffer RLS 40 mL RT O665690D Buffer RW1 40 mL RT O665690E Buffer RW2 (concentrate) 11 mL RT O665690F RNase-Free Water 10 mL RT O665690G Spin Columns FS with Collection Tubes 50 EA RT O665690H Spin Columns RM with Collection Tubes 50 EA RT O665690I RNase-Free Centrifuge Tubes (1.5 mL) 50 EA RTProduct IntroductionThis kit is suitable for extracting RNA from a wide range of plants, even from plants rich in polysaccharides and polyphenols, high quality RNA can be successfully extracted, such as rice leaves, wheat leaves, corn leaves, tobacco leaves, pine needles, ginkgo leaves, poplar leaves, pomegranate leaves, holly leaves, apples, peaches, pears, tomatoes, cherries, apricots, bananas, grapes, loquats, cinnamon rinds, cinnamon pulp, lychee fruit rinds, lychee pulp, soybean, peanut, corn, potato tuber, moonflower petal, pomegranate petal, shiitake mushroom, flat mushroom and other samples. The unique lysate formula can rapidly inactivate the RNA enzyme in the cell, effectively remove the effect of polysaccharide and polyphenol on RNA extraction, without the need for phenol, chloroform and other reagents, while using silicon matrix membrane adsorption of RNA for purification, the total RNA extracted is highly pure, without the contamination of genomes, proteins and other impurities, and can be used for Real Time RT-PCR, RT-PCR, It can be used for Real Time RT-PCR, RT-PCR, Northern Blot, Dot Blot, in vitro translation and other downstream experiments.RNA yieldSelf-contained reagents: β-mercaptoethanol, anhydrous ethanol (freshly opened or for RNA extraction)Pre-experiment Preparation and Important Notes1. To prevent RNase contamination, attention should be paid to the following aspects:1) Use RNase-free plastics and tips.(2) Operators wear disposable masks and gloves, and change gloves diligently during the experiment.2. Avoid repeated freezing and thawing of the extracted samples, otherwise it will affect the rate and quality of RNA extraction.3. If Buffer RLS produces a precipitate, heat to dissolve it and leave at room temperature.4. Please add β-mercaptoethanol to Buffer RLS before use, add 20µl β-mercaptoethanol to 1ml Buffer RLS. Buffer RLS with β-mercaptoethanol can be stored for 1 month at room temperature.5. Anhydrous ethanol should be added according to the instructions on the reagent bottle label before using Buffer RW2 for the first time. Operation steps1. Homogenization: Take 50-100mg of plant tissue and quickly grind it into powder in liquid nitrogen, add 500µl of Buffer RLS (please check whether β-mercaptoethanol is added before use), and immediately mix it by vortexing with vigorous shaking.Note: For materials that are extremely rich in water content, such as watermelon pulp, tomato, pear pulp, etc., more material can be added appropriately, up to 200 mg; for starch-rich samples or mature leaves, the amount of Buffer RLS can be increased appropriately, up to 700 µl.2. Centrifuge at 12,000 rpm (~13,400 x g) for 2 min at 4°C.3. Transfer the supernatant into the filter columns (Spin Columns FS) that have been loaded into the collection tubes, centrifuge at 12,000 rpm at 4°C for 1 minute, carefully aspirate the supernatant in the collection tubes and transfer it to new RNase-Free centrifugation tubes (self-provided), avoiding the tip of the gun from touching the cell debris precipitation in the collection tubes as much as possible.4. Slowly add 0.5 times the volume of the supernatant in anhydrous ethanol, mix well (a precipitate may appear), and transfer the resulting solution together with the precipitate to a Spin Columns RM in a collection tube, or in two batches if you cannot add all of the solution at once. centrifuge the column for 1 minute at 12,000 rpm at 4°C. Dispose of the spent solution and place the column back into the collection tube. Centrifuge at 12,000 rpm for 1 minute at 4°C, discard the spent solution and return the column to the collection tube.5. Add 350 µl of Buffer RW1 to the adsorbent column RM, centrifuge at 12,000 rpm at 4°C for 1 min, discard the waste solution and put the adsorbent column back into the collection tube.6. Preparation of DNase I mixture: Take 52µl of RNase-Free Water, add 8µl of 10×Reaction Buffer and 20µl of DNase I (1U/µl) to it, mix well, and prepare a final volume of 80µl of reaction solution.7. Add 80µl of DNase I mixture directly to the adsorption column and incubate at 20-30°C for 15 minutes.8. Add 350 µl of Buffer RW1 to the adsorbent column RM, centrifuge at 12,000 rpm at 4°C for 1 min, discard the waste solution and put the adsorbent column back into the collection tube.9. Add 500 µl of Buffer RW2 to the adsorbent column RM (check that anhydrous ethanol is added before use), centrifuge at 12,000 rpm for 1 minute at 4°C, discard the waste solution and put the adsorbent column back into the collection tube.10. Repeat step 9.11. Centrifuge at 12,000 rpm for 2 minutes at 4°C.Note: The purpose of this step is to remove residual ethanol from the adsorption column; ethanol residue can interfere with subsequent enzymatic reactions (zymography, PCR, etc.).12. Load the adsorption column RM into new RNase-Free Centrifuge Tubes (1.5 ml), add 30-50 µl of RNase-Free Water dropwise to the middle part of the adsorption membrane overhang, leave it at room temperature for 2 min, and centrifuge at 12,000 rpm at 4°C for 1 min, and store the resulting RNA solution at -70°C to prevent degradation.Note: 1) The volume of RNase-Free Water should not be less than 30 µl, too small volume affects the recovery rate.2) If you want to increase the RNA yield, repeat step 12 with 30-50 µl of fresh RNase-Free Water.3) If the RNA concentration is to be increased, the resulting solution can be reintroduced into the adsorption column and step 12 repeated... Read More |