| Description | Pyruvate phosphate dikinase (PPDK, EC 2.7.9.1) is a rate-limiting enzyme in the C4 pathway and Crassulacean acid metabolism (CAM) pathway. It catalyzes the three-step conversion of ATP, pyruvate, and Pi to phosphoenolpyruvate. This enzyme is primarily located in the chloroplast stroma of C4 plants Pyruvate phosphate dikinase (PPDK, EC 2.7.9.1) is a rate-limiting enzyme in the C4 pathway and Crassulacean acid metabolism (CAM) pathway. It catalyzes the three-step conversion of ATP, pyruvate, and Pi to phosphoenolpyruvate. This enzyme is primarily located in the chloroplast stroma of C4 plants and plays a crucial regulatory role in photosynthetic function. The assay measures PPDK activity based on its reverse reaction, which converts phosphoenolpyruvate, AMP, and PPi into pyruvate, ATP, and Pi. The generated pyruvate is then further catalyzed by lactate dehydrogenase (LDH) in the presence of NADH to produce lactate and NAD+. The rate of decrease in NADH absorbance at 340 nm is measured and used to calculate PPDK activity.Component100TStorageExtraction Buffer100 mL2-8℃Reagent 125 mL2-8℃Reagent 22 EA-20℃Reagent 3 40 µL2-8℃Note for Reagent 3: The volume is small. Briefly centrifuge the tube before use if the liquid is adhered to the wall.User-Prepared Instruments & Materials UV spectrophotometer or microplate reader, benchtop centrifuge, adjustable pipettes, micro quartz cuvette or 96-well plate, mortar, ice, and distilled water.Sample Preparation Homogenize the tissue sample on ice using a mortar and pestle in Extraction Buffer with a recommended ratio of 1:5 to 1:10 (tissue weight (g) : Extraction Buffer volume (mL)). (For example, weigh about 0.1 g of tissue and add 1 mL of Extraction Buffer). Centrifuge the homogenate at 8000 g, 4°C for 10 minutes. Collect the supernatant and keep it on ice for assay.Assay Procedure1. Instrument Setup: Preheat the spectrophotometer or microplate reader for at least 30 minutes. Set the wavelength to 340 nm. Zero the instrument with distilled water.2. Sample Measurement:2.1 Working Solution Preparation: Just before use, add one vial of Reagent 2 to 10 mL of Reagent 1 and add 5 µL of Reagent 3. Mix thoroughly and incubate at 37°C for 5 minutes. Any unused solution should be aliquoted and stored at -20°C. Avoid repeated freeze-thaw cycles.2.2 Reaction Setup: Add 10 µL of the sample supernatant and 190 µL of the Working Solution into a micro quartz cuvette or a well of a 96-well plate. Mix immediately and record the initial absorbance value at 340 nm (A1). After incubating at 37°C for exactly 5 minutes, record the absorbance value again (A2). Calculate ΔA = A1 - A2. PPDK Activity Calculation 1. Calculation for Micro Quartz Cuvette Assay: 1.1 Based on Sample Protein Concentration: Unit Definition: One unit of enzyme activity is defined as the amount that consumes 1 nmol of NADH per minute per mg of protein. Formula: PPDK Activity (nmol/min/mg prot) = [ΔA × V total_reaction ÷ (ε × d) × 10⁹] ÷ (V sample × Cpr) ÷ T = 643 × ΔA ÷ Cpr 1.2 Based on Sample Fresh Weight: Unit Definition: One unit of enzyme activity is defined as the amount that consumes 1 nmol of NADH per minute per gram of fresh tissue. Formula: PPDK Activity (nmol/min/g fresh weight) = [ΔA × V total_reaction ÷ (ε × d) × 10⁹] ÷ (W × V sample ÷ V total_extract ) ÷ T = 643 × ΔA ÷ W 2. Calculation for 96-Well Plate Assay: 2.1 Based on Sample Protein Concentration: Unit Definition: One unit of enzyme activity is defined as the amount that consumes 1 nmol of NADH per minute per mg of protein. Formula: PPDK Activity (nmol/min/mg prot) = [ΔA × V total_reaction ÷ (ε × d) × 10⁹] ÷ (V sample × Cpr) ÷ T = 1286 × ΔA ÷ Cpr 2.2 Based on Sample Fresh Weight: Unit Definition: One unit of enzyme activity is defined as the amount that consumes 1 nmol of NADH per minute per gram of fresh tissue. Formula: PPDK Activity (nmol/min/g fresh weight) = [ΔA × V total reaction ÷ (ε × d) × 10⁹] ÷ (W × V sample ÷ V total extract ) ÷ T = 1286 × ΔA ÷ W Parameters Explanation: V total_reaction : Total reaction volume, 2×10⁻⁴ L ε: Molar extinction coefficient of NADH, 6.22×10³ L/mol/cm d: Light path (1 cm for micro cuvette; 0.5 cm for 96-well plate) V sample : Volume of sample supernatant added, 0.01 mL V total extract : Total volume of extraction buffer added, 1 mL T: Reaction time, 5 min Cpr: Sample protein concentration, mg/mL W: Sample mass, g Notes It is essential to perform a preliminary assay using 2-3 samples expected to have significant activity differences before formal testing... Read More | Inquire | Product introduction：Used to isolate lymphocytes from human organsMatters needing attention：1. samples, reagents and experimental environment in the whole process shall be carried out at 20 ± 2 ℃. In order to obtain the best experimental results, it is best to carry out the Product introduction：Used to isolate lymphocytes from human organsMatters needing attention：1. samples, reagents and experimental environment in the whole process shall be carried out at 20 ± 2 ℃. In order to obtain the best experimental results, it is best to carry out the experiment within 2 h of sampling. The longer the sample is stored, the worse the cell separation effect is. The separation effect is even worse after the sample is placed for more than 6 h, or even cannot achieve the purpose of separation. 2. in this experiment, it is better not to use plastic products with high polymerization materials (such as polystyrene), but use non-static, low static ionization heart tubes and glass products without alkali treatment, because the electrostatic effect will lead to cell adhesion, and the surface of alkali treated glass will become rough, which will affect the effect of cell separation. 3. aspirating too many lymphocyte layers and separation liquid layers will cause the granulocytes at the junction of separation liquid to be aspirated, thus increasing the number of mixed granulocytes. 4. when the amount of separating solution is greater than that of tissue single cell suspension sample, the separation effect is better.Scope of application：Lymphocyte isolation... Read More | DescriptionGreen LED Array for Photo KitAlysis high-throughput screening platform. For use with Photo KitAlysis Starter Kit (Z742612). User guide is provided in the below hyperlink.Photo KitAlysis Operating InstructionsFeatures:Designed and tested by synthetic chemists.Controller provides repeatableDescriptionGreen LED Array for Photo KitAlysis high-throughput screening platform. For use with Photo KitAlysis Starter Kit (Z742612). User guide is provided in the below hyperlink.Photo KitAlysis Operating InstructionsFeatures:Designed and tested by synthetic chemists.Controller provides repeatable milliamp selection for photon intensity (sold seperately)527 nm wavelength0-30 mA variable LED outputNon-magnetic LED baseChemically resistant LED coverPTFE coated cablingPhoto Kitalysis Starter Kitrequired for operation (sold separately). Best when used withKitAlysis Benchtop Inertion Box(sold separately)... Read More | Products contentProducts IntroductionThis kit is suitable for simple, rapid and efficient isolation and purification of DNA/RNA from whole blood, tissue homogenates, swabs, serum, plasma and other cell-free body fluids, etc. The unique buffer system enables the viral nucleic acids in the lysate to Products contentProducts IntroductionThis kit is suitable for simple, rapid and efficient isolation and purification of DNA/RNA from whole blood, tissue homogenates, swabs, serum, plasma and other cell-free body fluids, etc. The unique buffer system enables the viral nucleic acids in the lysate to bind to the silica gel centrifugal adsorbent columns in a highly efficient manner, and the viral nucleic acids obtained are of high purity and stable quality, free of protein, nuclease and other impurities, and can be used in a variety of routine operations, including PCR, fluorescence quantitative PCR and other experiments. It can be used for a variety of routine operations, including PCR, fluorescence quantitative PCR and other experiments.Bring your own instrumentsThermostatic mixer.Pre-experiment Preparation and Important Notes1. Read these instructions carefully before experimenting.2. If Proteinase K is to be stored for a long period of time, please keep it at -20℃.3. Check Buffer RLC for crystallization or precipitation prior to use, and if crystallization or precipitation occurs, redissolve Buffer RLC in a 56°C water bath.4. Pre-treatment of tissue samples: Take 20 mg of tissue samples into 1.5 mL centrifuge tubes (self-provided), add 500 µL of Buffer RLC, and after the tissue homogenizer breaks up, centrifuge the samples for 1 minute at 12,000 rpm (~13,400×g), and take 200 µL of supernatant as samples. procedure1. Take a 1.5 mL centrifuge tube (provided), add 500 µL of Buffer RLC, 200 µL of sample, 20 µL of Proteinase K, vortex for 5 s, and then place it in a thermostatic mixer at 1200 rpm for 10 min at room temperature. Note: For wet swab samples, 200 µL of sample was taken after sufficiently shaking and mixing. Note: For wet swabs, 200 µL was taken from the sample after it was soaked in 400 µL of saline, shaken and mixed thoroughly for 5 minutes, and then centrifuged at 12,000 rpm for 1 minute, and 200 µL was taken for extraction.2. Instantly remove the centrifuge tube and add the solution from step 1 to the Spin Columns DM in the collection tube. centrifuge at 12,000 rpm (~13,400 x g) for 1 minute, pour off the waste liquid from the collection tube, and return the column to the collection tube.3. Add 500 µL of Buffer PGWT to the adsorbent column, centrifuge at 12,000 rpm for 1 minute, pour off the waste liquid from the collection tube, and return the column to the collection tube.4. Add 500 µL of Buffer GWT2 to the adsorbent column, centrifuge at 12,000 rpm for 1 minute, pour off the waste liquid from the collection tube, and return the column to the collection tube.5. Centrifuge at 12,000 rpm for 2 minutes and pour off the waste liquid in the collection tube. Place the adsorption column at room temperature for 2 minutes and allow to dry.6. Place the column in a new collection tube (RNase-Free Centrifuge Tube), add 40-100 µL of RNase-Free Water to the center of the column membrane, let it stand at room temperature for 2 minutes, and then centrifuge at 12,000 rpm for 1 minute to collect the nucleic acid solution. Store at -80℃ for a long time... Read More |