| Description | Inquire | Inquire | Product content C665709Component50 TStorageC665709ABuffer CL45 mLRTC665709BBuffer CB (concentrate)60 mLRTC665709CBuffer GW1 (concentrate)13 mLRTC665709DBuffer GW2 (concentrate)15 mLRTC665709EBuffer EBL10 mLRTC665709FProteinase K100 mgRTC665709GProteinase K Storage Buffer5 mLRTC665709HSpin Columns DFProduct content C665709Component50 TStorageC665709ABuffer CL45 mLRTC665709BBuffer CB (concentrate)60 mLRTC665709CBuffer GW1 (concentrate)13 mLRTC665709DBuffer GW2 (concentrate)15 mLRTC665709EBuffer EBL10 mLRTC665709FProteinase K100 mgRTC665709GProteinase K Storage Buffer5 mLRTC665709HSpin Columns DF with Collection Tubes50 EA2-8℃C665709ICentrifuge Tubes (L-1.5 mL)50 EART Product IntroductionThis kit is suitable for the extraction of free DNA from fresh or frozen serum, plasma, lymph fluid and other cell-free body fluids.This kit adopts centrifugal adsorption columns that can specifically bind nucleic acids and a unique buffer system.After the sample is lysed, the free DNA binds to the silica gel membrane under high salt conditions, and the free DNA elutes from the silica gel membrane at low salt and high pH. The product can handle liquid samples of 0.1-1 ml, and the elution volume of the configured high-efficiency micro adsorption column can be as low as 20 µl. The purified DNA is of high yield and quality, with maximum removal of proteins, pigments, lipids, and other inhibitors, and the rate of free DNA yield is highly dependent on the type of samples, storage conditions, time, and inter-individual variations. The quality of free DNA obtained from purification is stable and reliable, and can be directly used in molecular biology experiments such as PCR, fluorescence quantitative PCR and second generation sequencing.Self-contained reagents: anhydrous ethanol, isopropanol.Pre-experiment Preparation and Important NotesAdd 5 ml of Proteinase K Storage Buffer to Proteinase K to dissolve it and store it at -20℃. Do not leave the prepared Proteinase K at room temperature for a long time.Repeated freezing and thawing of the sample should be avoided, as this can lead to a decrease in extraction.This kit can extract 0.1-1 ml of liquid samples.Before use, please check Buffer CL, Buffer CB for crystallization or precipitation, if there is any crystallization or precipitation, please re-dissolve Buffer CL, Buffer CB by incubation at 56℃ in a water bath.Before first use isopropyl alcohol should be added to Buffer CB according to the instructions on the reagent bottle label, mixed well, and labeled on the reagent bottle label.Before the first use, anhydrous ethanol should be added to Buffer GW1 and Buffer GW2 according to the instructions on the label of the reagent bottle, mixed well, and labeled on the label of the reagent bottle.Preheat the water bath to 60°C before starting the experiment.The elution buffer Buffer EBL can be preheated to 60°C and used.Operation stepsAdd 20 µl of Proteinase K to the centrifuge tube (supplied).Add 200 µl of serum/plasma sample.Note: When the sample volume exceeds 200 µl, please increase the amount of Proteinase K, Buffer CL and Buffer CB reagents in equal proportions, and the specific amount of reagents added can be referred to the attached table.3. Add 160 µl Buffer CL, mix upside down and shake vigorously for at least 30 seconds.4. Incubate at 60°C for 30 minutes, during which time mixing was inverted several times.Note: Incubation of 200µl serum/plasma samples at 60°C for 10-15 minutes is sufficient.Add 360 µl of Buffer CB (check for addition of isopropanol before use) and shake until thoroughly mixed.Ice bath for 5 minutes and centrifuge briefly to concentrate the liquid on the walls and wall caps to the bottom of the tube.Add all of the solution obtained in step 6 to the adsorption columns (Spin Columns DF) that have been loaded into the collection tubes, and if the solution cannot be added all at once, it can be transferred in several times. centrifuge the columns at 12,000 rpm for 1 minute, pour off the waste solution from the collection tubes, and put the columns back into the collection tubes.Add 500µl of Buffer GW1 to the adsorbent column (check that anhydrous ethanol is added before use),centrifuge the column at 12,000rpm for 30 seconds, pour off the waste liquid in the collection tube, and put the adsorbent column back into the collection tube.Add 750 µl Buffer GW2 to the adsorbent column (check that anhydrous ethanol is added before use), centrifuge at 12,000 rpm for 30 seconds, pour off the waste liquid in the collection tube, and put the adsorbent column back into the collection tube.10. Add 750 µl of anhydrous ethanol to the adsorbent column and centrifuge at 12,000 rpm for 30 s. Pour off the waste liquid in the collection tube and put the adsorbent column back into the collection tube.11. Centrifuge at 12,000 rpm for 2 minutes and pour off the waste liquid in the collection tube. Leave the adsorption column at room temperature for several minutes to dry thoroughly.Note: The purpose of this step is to remove residual ethanol from the adsorption column, which can interfere with the subsequent enzymatic reaction.12. Place the adsorption column in a new centrifuge tube, add 20-100 µl Buffer EBL or sterilized water to the middle part of the adsorption column overhanging the column, leave it at room temperature for 2-5 minutes, centrifuge at 12,000 rpm for 1 minute, collect the DNA solution, and store the DNA at -20℃.Note: 1) If the downstream experiment is sensitive to pH, you can use sterilized water for elution. The pH value of the eluent has a great influence on the elution efficiency, if water is used as the eluent should ensure that its pH value is 7.0-8.5 (you can use NaOH to adjust the pH value of water to this range), and the elution efficiency is not high when the pH value is lower than 7.0.2) Preheat the elution buffer BufferEBL to 60℃ and use it, and incubate it at room temperature for 5 minutes before centrifugation to increase the yield.3) If the final concentration of DNA is to be increased, the resulting solution can be reintroduced into the adsorption column and left at room temperature for 2-5 minutes and centrifuged at 12,000 rpm for 1 minute.4) Because DNA preserved in water will be affected by acidic hydrolysis, for long-term storage, it is recommended to elute it with Buffer EBL and store it at -20℃.Table: Recommended reagent additions for different sample sizes... Read More | Products R669890Component50 TStorageR669890ADNase I1000 U-20℃. Avoid freeze/thaw cycle.R669890B10×Reaction Buffer1mL-20℃. Avoid freeze/thaw cycle.R669890CBuffer RL35 mLRTR669890DBuffer RW140 mLRTR669890EBuffer RW2 (concentrate)11 mLRTR669890FRNase-Free Water10 mLRTR669890GSpin Products R669890Component50 TStorageR669890ADNase I1000 U-20℃. Avoid freeze/thaw cycle.R669890B10×Reaction Buffer1mL-20℃. Avoid freeze/thaw cycle.R669890CBuffer RL35 mLRTR669890DBuffer RW140 mLRTR669890EBuffer RW2 (concentrate)11 mLRTR669890FRNase-Free Water10 mLRTR669890GSpin Columns FL with Collection Tubes50 setsRTR669890HSpin Columns RM with Collection Tubes50 setsRTR669890IRNase-Free Centrifuge Tubes (1.5 mL)100 EART ProductsThis kit adopts centrifugal adsorption columns with high efficiency and specificbinding of nucleic acids and unique buffer system, which can rapidly extract totalRNA from bacteria or cultured animal cells.The reaction can be completed in 30-40minutes, and the extracted total RNA is extremely pure and free of protein and othercontaminants, which is suitable for RT-PCR, Real-Time RT-PCR, microarray analysis,in vitro translation and other experiments. Self-contained reagents: Lysozyme, β-mercaptoethanol, anhydrous ethanol (freshlyopened or for RNA extraction). Pre-experiment Preparation and Important Notes 1. To prevent RNase contamination, attention should be paid to the following aspects:1) Use RNase-free plastics and tips to avoid cross-contamination. 2) RNase-free water should be used to prepare the solution. 3) Operators wear disposable masks and gloves, and change gloves diligently duringthe experiment. 2. Add β-mercaptoethanol to Buffer RL before use to reach a final concentrationof 1%, e.g., add 10 µl of β-mercaptoethanol to 1 ml of Buffer RL. Buffer RL withβ-mercaptoethanol can be stored at 4℃ for 1 month, if precipitation occurs, pleaseheat to dissolve and use.3. Anhydrous ethanol should be added to Buffer RW2 before first use according tothe instructions on the reagent bottle label. 4. All centrifugation steps are carried out at room temperature if not otherwisespecified, and all steps should be performed quickly. Procedure 1. Centrifuge at 12,000 rpm (~13,400 x g) at 4°C for 2 minutes to collect theorganisms (maximum volume of organisms should not exceed 1 x 109) and carefullyremove all supernatants. Note: Supernatants that leave residues can interfere with the subsequent digestionprocess. 2. Thoroughly resuspend the organisms with 100 µl of TE buffer containing Lysozymeand incubate at room temperature. The specific formulation and incubation time areas follows:/The final concentration of Lysozyme in TE bufferincubation timeG-germ400µg/ml3-5minG+germ3mg/ml5-10min 3. Add 350 µl of Buffer RL (check that β-mercaptoethanol has been added beforeuse), vortex and shake to mix (insoluble precipitate may appear in this step), addall of the solution and the precipitate to the filter columns (Spin Columns FL) thathave been loaded into the collection tubes, and centrifuge at 12,000 rpm for 2minutes. 4. Add 250 µl of anhydrous ethanol to the filtrate obtained in the previous stepand mix well (a precipitate may appear at this point). Transfer the resulting solution together with the precipitate to a Spin Columns RM packed in a collectiontube, centrifuge at 12,000 rpm for 1 min, discard the waste solution and put thecolumn back into the collection tube.5. Add 350 µl Buffer RW1 to the adsorbent column, centrifuge at 12,000 rpm for1min, discard the waste liquid and put the adsorbent column back into the collectiontube.6. Preparation of DNase I mixture: Take 52µl of RNase-Free Water, add 8µl of 10×Reaction Buffer and 20µl of DNase I (1U/µl) to it, mix well, and make a finalvolume of 80µl of reaction solution.7. Add 80µl of DNase I mixture directly to the adsorption column and incubate at20-30°C for 15 minutes.8. Add 350 µl Buffer RW1 to the adsorbent column, centrifuge at 12,000 rpm for1min, discard the waste liquid and put the adsorbent column back into the collectiontube.9. Add 500 µl of Buffer RW2 to the column (check that anhydrous ethanol is addedbefore use), centrifuge at 12,000 rpm for 1 min, and discard the waste solution.10. Repeat step 9.11. Place the adsorbent column back into the collection tube and centrifuge at 12,000rpm for 2 minutes. Note: The purpose of this step is to remove residual ethanol from the adsorptioncolumn; ethanol residue can interfere with subsequent enzymatic reactions (zymography, PCR, etc.).12. Load the adsorption column into a new RNase-Free collection tube, add 30-50 µl of RNase-Free Water to the middle of the adsorption membrane, leave it at roomtemperature for 1 minute, centrifuge at 12,000 rpm for 1 minute, collect the RNAsolution, and store the RNA at -70°C to prevent degradation. Note: 1) The volume of RNase-Free Water should not be less than 30 µl, too smallvolume affects the recovery rate. 2) If you want to increase the RNA yield, repeat step 12 with 30-50 µl of freshRNase-Free Water. If the RNA concentration is to be increased, the resulting solution can be reintroduced into the adsorption column and step 12 repeated... Read More | This reagent kit is designed based on the principle that biotin and Streptavidin have a strong affinity. After the primary antibody of rabbit or mouse origin binds to the corresponding target antigen, the biotinylated antibody in this kit • • Rabbit/mouse universal secondary antibody This reagent kit is designed based on the principle that biotin and Streptavidin have a strong affinity. After the primary antibody of rabbit or mouse origin binds to the corresponding target antigen, the biotinylated antibody in this kit • • Rabbit/mouse universal secondary antibody specifically binds to the primary antibody; The biotin labeled on the secondary antibody binds to streptavidin labeled with peroxidase (HRP), forming an antigen-specific primary antibody biotinylated secondary antibody streptavidin complex labeled with HRP. HRP can catalyze substrate colorimetry, thereby inferring the presence and distribution of the tested antigen. The biotinylated secondary antibody and SA-HRP used in this reagent kit all adopt optimized labeling and purification techniques, which make their staining more sensitive and have a lower background. They are suitable for detecting formalin fixed paraffin embedded tissue sections, as well as frozen sections, cell slides, freshly prepared blood smears, etc. The rabbit/mouse universal Streptavidin HRP kit is suitable for use with aladdin ready to use or concentrated antibodies. Composition：Note: This reagent kit is only suitable for IHC experiments where the primary antibody is an immune or mouse derived antibodNotes:1. Add 1 drop (approximately 50) to each slice µ l) Calculation: 3ml can make 60 slices, and 18ml can make 360 slices.2.For tissues with abundant endogenous biotin content, it is best to use endogenous biotin blockers for blocking when using this kit.3. DAB working solution is prepared and used immediately, and the prepared working solution is effective within 1 hour in the dark at 2-8 ° C.4. During the experiment, avoid drying the tissue slices, so the amount of working fluid used during each incubation step must be sufficient to ensure complete coverage of the tissue sample, and incubation should be carried out in a wet box as much as possible.5. To obtain the best experimental results, please make sure to optimize the experimental conditions and reagent dosage.6. DAB is a suspected carcinogen, please take necessary protective measures when using it. 7. This product is only for scientific research and cannot be used for human reactions or treatments.Operation steps：1. Routine processing of samples such as paraffin or frozen tissue sections or cell slides to be tested.1) Preparation for staining of tissue sections or cell slides: a. Dewaxing and hydration of paraffin sections: bake at 60 º C for 1 hour, dewaxing twice with xylene for 5 minutes each time; Then immerse in gradient ethanol (anhydrous ethanol anhydrous ethanol 95% 85% 75% ethanol) and distilled water for 5 minutes each for hydration. b. Frozen sections and cell climbing sections (or climbing sections) were soaked in 0.01 M pH 7.4 PBS and washed 3 times for 5 minutes. Then cover the tissue (or cells) with 0.1% Triton X-100 and infiltrate for 15 minutes. Wash twice with 0.01 M pH 7.4 PBS for 5 minutes.2) Antigen repair of paraffin sections: In most cases, high-pressure repair with citric acid buffer is suitable for paraffin tissue sections. Preparation of repair solution: Add 10 ml of citric acid buffer (IHC antigen repair solution, 100 x) to 1 L of deionized water, and mix well. Repair process: The repair solution is added to a high-pressure cooker, and the repaired slices are immersed in the repair solution (must have no tissue). Cover the pressure cooker cover, heat until evenly sprayed with steam, and start timing from the spraying. After 1-2 minutes, the pressure cooker leaves the heat source and cools naturally to room temperature. Remove the slices, rinse with distilled water, and rinse twice with PBS (0.01 M pH 7.4) for 3 minutes each time.2. Add an appropriate amount of Solution A white solution, which is an endogenous peroxidase blocking solution, and incubate at room temperature for 10 minutes, then rinse thoroughly with PBS.3. Add an appropriate amount of Solution B white solution dropwise, which is sealed with normal sheep serum working solution. Incubate at room temperature for 10 minutes and shake dry.4. Add an appropriate amount of primary antibody working solution (commercial ready to use antibodies or concentrated antibodies diluted in appropriate proportions) dropwise, incubate according to experimental requirements, and then rinse thoroughly with PBS.5. Add an appropriate amount of Solution C yellow solution, namely biotin labeled sheep anti rabbit/mouse secondary antibody working solution, incubate at room temperature for 10 minutes, and rinse thoroughly with PBS.6. Add an appropriate amount of Solution D red solution, which is HRP labeled streptavidin. Incubate at room temperature for 10 minutes and rinse thoroughly with PBS.7. Preparation of DAB color working solution: According to the required amount, mix DAB-A and DAB-B in a volume ratio of 1:19 to obtain DAB color working solution. Alternatively, one drop (approximately 50) can be added per milliliter of reagent B µ l) Reagent A, mix well.8. Color development: Add an appropriate amount of DAB color development working solution to the tissue section or cell slide that needs to be developed, and the color development time is generally 1-5 minutes. Observe and control the color development time under a microscope. When the optimal color development effect is achieved, rinse with tap water to terminate the color development. The colored slices are re stained, dehydrated and transparent, and can be stored for a long time after sealing... Read More |