| Description | Catalase (CAT, EC 1.11.1.6) is widely found in animals, plants, microorganisms, and cultured cells. It is the primary H₂O₂-scavenging enzyme and plays a crucial role in the reactive oxygen species (ROS) scavenging system. H₂O₂ has a characteristic absorption peak at 240 nm. Catalase (CAT, EC 1.11.1.6) is widely found in animals, plants, microorganisms, and cultured cells. It is the primary H₂O₂-scavenging enzyme and plays a crucial role in the reactive oxygen species (ROS) scavenging system. H₂O₂ has a characteristic absorption peak at 240 nm. CAT decomposes H₂O₂, causing the absorbance of the reaction solution at 240 nm to decrease over time. The CAT activity can be calculated based on the rate of change in absorbance.Component50TStorageExtraction Buffer60 mL2-8℃Working Solution60 mL2-8℃User-Prepared Instruments and ReagentsUV spectrophotometer, benchtop centrifuge, adjustable pipettes, 1 mL quartz cuvette, mortar, ice, and distilled water.Experimental Procedure1. Crude Enzyme Extract Preparation1.1 Bacterial/Cell SamplesCollect bacteria or cells into a centrifuge tube, centrifuge, and discard the supernatant. Use a bacteria/cell count (10⁴) to Extraction Buffer volume (mL) ratio between 500:1 and 1000:1 (recommended: 5 million bacteria/cells in 1 mL Extraction Buffer). Disrupt the bacteria or cells by sonication (ice bath, power 20% or 200W, pulse 3s on, 10s off, repeat 30 times). Centrifuge at 8,000 g, 4°C for 10 minutes. Collect the supernatant and keep it on ice for assay.1.2 Tissue SamplesUse a tissue mass (g) to Extraction Buffer volume (mL) ratio between 1:5 and 1:10 (recommended: weigh approx. 0.1 g tissue, add 1 mL Extraction Buffer). Homogenize in an ice bath. Centrifuge at 8,000 g, 4°C for 10 minutes. Collect the supernatant and keep it on ice for assay.1.3 Serum (Plasma) SamplesAssay directly.2. Assay Steps2.1 Preheat the spectrophotometer for at least 30 minutes. Set the wavelength to 240 nm. Zero the instrument with distilled water.2.2 Before assay, incubate the CAT Working Solution in a water bath at 37°C (for mammals) or 25°C (for other species) for 10 minutes.2.3 Add 35 µL of sample and 1 mL of Working Solution into a 1 mL quartz cuvette. Mix well and immediately measure the initial absorbance at 240 nm (A₁). Measure the absorbance again after 1 minute (A₂). Calculate ΔA = A₁ - A₂.3. CAT Activity Calculation3.1 Calculation of CAT Activity in Serum (Plasma)Unit Definition: One unit of enzyme activity is defined as the amount that catalyzes the degradation of 1 nmol of H₂O₂ per minute per milliliter of serum (plasma).Derived Formula:CAT Activity (nmol/min/mL) = [ΔA × Vtotal reaction÷ (ε × d) × 10⁹] ÷ Vsample÷ TSimplified Formula:CAT Activity (nmol/min/mL) = 678 × ΔA3.2 Calculation of CAT Activity in Tissues, Bacteria, or Cells(1) Based on Sample Protein ConcentrationUnit Definition: One unit of enzyme activity is defined as the amount that catalyzes the degradation of 1 nmol of H₂O₂ per minute per milligram of tissue protein.Derived Formula:CAT Activity (nmol/min/mg prot) = [ΔA × Vtotal reaction÷ (ε × d) × 10⁹] ÷ (Vsample× Cpr) ÷ TSimplified Formula:CAT Activity (nmol/min/mg prot) = 678 × ΔA ÷ Cpr(2) Based on Sample Fresh WeightUnit Definition: One unit of enzyme activity is defined as the amount that catalyzes the degradation of 1 nmol of H₂O₂ per minute per gram of tissue.Derived Formula:CAT Activity (nmol/min/g fresh weight) = [ΔA × Vtotal reaction÷ (ε × d) × 10⁹] ÷ (W × Vsample÷ Vtotal sample) ÷ TSimplified Formula:CAT Activity (nmol/min/g fresh weight) = 678 × ΔA ÷ W(3) Based on Bacterial or Cell DensityUnit Definition: One unit of enzyme activity is defined as the amount that catalyzes the degradation of 1 nmol of H₂O₂ per minute per 10⁴ bacteria or cells.Derived Formula:CAT Activity (nmol/min/10⁴ cells) = [ΔA × Vtotal reaction÷ (ε × d) × 10⁹] ÷ (500 × Vsample÷ Vtotal sample) ÷ TSimplified Formula:CAT Activity (nmol/min/10⁴ cells) = 1.356 × ΔAParameter Definitions:1.ΔA: Change in absorbance (A₁ - A₂)2.Vtotal reaction: Total reaction volume (1.035 × 10⁻³ L)3.ε: Molar extinction coefficient of H₂O₂ (4.36 × 10⁴ L/mol/cm)4.d: Light path length of the cuvette (1 cm)5.10⁹: Unit conversion factor (1 mole = 10⁹ nmoles)6.Vsample: Volume of sample added to the reaction (0.035 mL)7.T: Reaction time (1 min)8.Cpr: Sample protein concentration (mg/mL)9.W: Sample weight (g)10.Vtotal sample: Total volume of extraction buffer added (1 mL)11.500: Total number of bacteria or cells (5 million)Precautions1.Before formal testing, it is essential to perform a preliminary test with 2-3 samples expected to have significant differences.2.This product is for research use only. Not for use in clinical diagnosis.Frequently Asked Questions (FAQ)Q: What should I do if I get a negative value?A: Check if bubbles formed during the reaction. Excessive bubbling indicates very high enzyme activity, and bubbles can interfere, causing negative values. Try diluting the sample 10-fold with Extraction Buffer and re-assaying. If no bubbles form (with diluted sample or original reaction) and a small negative value persists, it indicates that the enzyme activity in this sample is below the detection limit... Read More | EndoFree Plasmid Midi Kit Cat No. Component Size（50T） Storage E665631A Buffer P1 30 mL RT E665631B Buffer P2 30 mL RT E665631C Buffer E3 30 mL RT E665631D Buffer PS 15 mL RT E665631E Buffer PW (concentrate) 10 mL RT E665631F Endo-free Buffer EB 10 mL RTEndoFree Plasmid Midi Kit Cat No. Component Size（50T） Storage E665631A Buffer P1 30 mL RT E665631B Buffer P2 30 mL RT E665631C Buffer E3 30 mL RT E665631D Buffer PS 15 mL RT E665631E Buffer PW (concentrate) 10 mL RT E665631F Endo-free Buffer EB 10 mL RT E665631G RNase A (10 mg/mL) 600 µL RT E665631H Buffer ER 8 mL RT E665631I CWBlue 300 µL RT E665631J Spin Columns DL with Collection Tubes 50 EA RT E665631K Endo-Remover FM with Collection 50 EA RTProduct Introduction:Endotoxins are a common pollutant in plasmid extraction. Due to the high sensitivity of eukaryotic cells to endotoxins, the presence of endotoxins in plasmids can greatly reduce the transfection efficiency of eukaryotic cells. This reagent kit provides a simple, fast, and efficient new method for extracting endotoxin free plasmids. The extracted plasmids can remove endotoxins to the maximum extent possible and effectively remove contamination of genomic DNA, RNA, proteins, and other substances. This reagent kit is suitable for extracting 5-15mL of bacterial solution. On the basis of alkaline lysis of cells, it efficiently and specifically binds plasmid DNA through a new silicon-based membrane. Each adsorption column can adsorb up to 100 µ The plasmid DNA of g is effectively removed using a special buffer system and endotoxin removal filter column, effectively removing impurities such as endotoxins and proteins. The plasmid obtained from this kit has high purity and stable quality, making it particularly suitable for cell transfection. It can also be used for downstream experiments such as DNA sequencing, PCR, PCR based mutations, in vitro transcription, transformed bacteria, and endonuclease digestion.Self prepared reagents: anhydrous ethanol, isopropanol.Preparation and important precautions before the experiment:1. All components can be stably stored in a dry, room temperature (15-30 ℃) environment for 1 year, and can be stored at 2-8 ℃ for longer periods of time. Buffer P1 with RNase A added can be stably stored at 2-8 ℃ for 6 months.2. Before the first use, add all RNase A solution to Buffer P1, mix well, and store at 2-8 ℃. Before use, let it sit at room temperature for a period of time. After returning to room temperature, use.3.Before the first use, anhydrous ethanol should be added to the Buffer PW according to the instructions on the reagent bottle label.4. Before use, please check if there is any crystallization or precipitation in Buffer P2 and Buffer E3. If there is any crystallization or precipitation, you can take a water bath at 37 ℃ for a few minutes to restore clarity.5. Be careful not to come into direct contact with Buffer P2 and Buffer E3, and immediately cover them tightly after use.6.The amount and purity of plasmid extraction are related to factors such as bacterial culture concentration, strain type, plasmid size, and plasmid copy number.Operation steps:1. Take 5-15 mL of overnight cultured bacterial solution and add it to a centrifuge tube (self provided). Centrifuge at 13000 rpm (~16200 × g) for 1 minute to collect bacteria, and try to discard all the supernatant as much as possible.2. Add 500 to the centrifuge tube containing bacterial sediment µ L Buffer P1 (please check if RNase A has been added first), mix thoroughly with a pipette or vortex oscillator, and suspend bacterial precipitation. Attention: If the bacterial blocks are not thoroughly mixed, it will affect the cracking effect, resulting in low extraction amount and purity.3. Add 500 to the centrifuge tube µ L Buffer P2, gently invert and mix 8-10 times, allowing the bacterial cells to fully lyse. Leave at room temperature for 3-5 minutes. At this point, the solution should become clear and viscous. Attention: Mix gently and do not shake vigorously to avoid interrupting genomic DNA and mixing genomic DNA fragments in the extracted plasmid. If the solution does not become clear, it indicates that the bacterial count may be too high and the lysis may not be complete. The bacterial count should be reduced.4. Add 500 to the centrifuge tube µ L Buffer E3, immediately invert and mix 8-10 times until white flocculent precipitates appear. Let it stand at room temperature for 5 minutes. Centrifuge at 13000 rpm for 5 minutes, extract the supernatant, and add it to the filter column (Endo Remove FM) (already loaded into the collection tube). Centrifuge at 13000 rpm for 1 minute to filter, then transfer the filtrate from the collection tube to the centrifuge tube (self provided). Attention: 1) After adding Buffer E3, it should be immediately mixed to avoid local precipitation. 2) The maximum volume of the adsorption column is 750 µ L. So please filter the supernatant twice and mix it in the same self provided centrifuge tube.5. Add 450 to the filtrate µ Mix L isopropanol upside down.6. Column balance: Add 200 to the spin columns DL that have been loaded into the collection tube µ L Buffer PS, centrifuge at 13000 rpm for 2 minutes, discard the waste liquid in the collection tube, and place the adsorption column back into the collection tube.7. Transfer the mixed solution of filtrate and isopropanol from step 5 to an equilibrium adsorption column (already loaded into a collection tube). 8.13000 rpm for 1 minute, discard the waste liquid in the collection tube, and place the adsorption column back into the collection tube. Attention: The maximum volume of the adsorption column is 750 µ L. So the solution obtained in step 5 is divided multiple times and passed through the column. 9. Add 750 to the adsorption column µ L Buffer PW (please check if anhydrous ethanol has been added first), centrifuge at 13000 rpm for 1 minute, and discard the waste liquid in the collection tube.10. Place the adsorption column back into the recovery manifold and centrifuge at 13000 rpm for 1 minute.Note: The purpose of this step is to remove residual ethanol from the adsorption column, which can affect subsequent enzymatic reactions (such as enzyme digestion, PCR, etc.).11. Place the adsorption column in a new centrifuge tube (self provided)... Read More | Product contentcomponent50T200TBuffer LP125mL100mLBuffer LP210mL40mLBuffer LP3 (concentrate)21ml84mlBuffer GW2 (concentrate)15mL75mlBuffer GE15mL60mLRNase A（10 mg/ml）300µl1.25mLSpin Columns DM with Collection Tubes50200ProductsThis kit uses centrifugal adsorption columns with highProduct contentcomponent50T200TBuffer LP125mL100mLBuffer LP210mL40mLBuffer LP3 (concentrate)21ml84mlBuffer GW2 (concentrate)15mL75mlBuffer GE15mL60mLRNase A（10 mg/ml）300µl1.25mLSpin Columns DM with Collection Tubes50200ProductsThis kit uses centrifugal adsorption columns with high efficiency and specific binding of nucleic acids and a unique buffer system, which is suitable for extracting genomic DNA from a wide variety of different fresh or frozen plant tissues with maximum removal of impurities from the plant tissues. The kit eliminates the need for phenol/chloroform extraction and is safe to handle. The extracted genomic DNA fragments are large, high purity, stable and reliable quality, suitable for PCR, fluorescence quantitative PCR, molecular labeling, library construction and other experiments.Self-contained reagent: anhydrous ethanolPre-experiment Preparation and Important Notes1. Repeated freezing and thawing of the sample should be avoided, as this may result in smaller fragments of extracted DNA and a decrease in the amount extracted.2. Anhydrous ethanol should be added to Buffer LP3 and Buffer GW2 according to the instructions on the label of the reagent bottle before first use. Check Buffer LP1 and Buffer LP2 for crystallization or precipitation before use. If crystallization or precipitation occurs, re-dissolve Buffer LP1 and Buffer LP2 in a 56°C water bath. Procedure1. Take about 100mg of fresh plant tissue or about 20mg of dry weight tissue and add liquid nitrogen to grind it fully.2. Collect the ground powder into a centrifuge tube (self-provided), add 400 µl Buffer LP1 and 6 µl RNase A (10 mg/ml), vortex and oscillate for 1 minute, and leave it at room temperature for 10 minutes to allow for full cleavage.Note: 1) Use vortex shaking or pipette blowing to fully lyses the tissue, incomplete tissue lysis will affect the final DNA yield. 2) Do not mix Buffer LP1 with RNase A prior to use.3. Add 130 µl Buffer LP2, mix well and vortex for 1 minute.4. Centrifuge at 12,000 rpm (~13,400 x g) for 5 minutes and transfer the supernatant to a new centrifuge tube (supplied).5. Add 1.5 times the volume of Buffer LP3 (check that anhydrous ethanol has been added before use) and mix thoroughly (e.g., 500 µl filtrate to 750 µl Buffer LP3).Note: Buffer LP3 should be mixed immediately after addition; precipitation may occur but will not affect subsequent experiments.6. Add all of the solution and precipitate obtained in the previous step to the adsorption columns (Spin Columns DM) that have been loaded into the collection tubes, if the solution cannot be added all at once, it can be transferred in several times. centrifuge the columns at 12,000 rpm for 1 minute, pour off the waste liquid in the collection tubes, and put the columns back into the collection tubes.7. Add 500 µl of Buffer GW2 to the adsorption column (check that anhydrous ethanol has been added before use), centrifuge at 12,000 rpm for 1 minute, pour off the waste liquid in the collection tube, and put the adsorption column back into the collection tube.Note: If the adsorbent membrane appears green, add 500 µl of anhydrous ethanol to the adsorbent column, centrifuge the column at 12,000 rpm for 1 minute, pour off the waste liquid in the collection tube, and put the adsorbent column back into the collection tube.8. Repeat step 7.9. Centrifuge at 12,000 rpm for 2 minutes and pour off the waste liquid in the collection tube. Leave the adsorption column at room temperature for several minutes to dry thoroughly.Note: The purpose of this step is to remove residual ethanol from the adsorption column, which can interfere with subsequent enzymatic reactions (digestion, PCR, etc.).10. Place the adsorption column in a new centrifuge tube (supplied), add 50-100 µl of Buffer GE or sterilized water dropwise to the middle of the adsorbent membrane, leave it at room temperature for 2-5 minutes, and centrifuge it at 12,000 rpm for 1 minute to collect the DNA solution. -The DNA solution was collected by centrifugation at 12,000 rpm for 1 min.Note: 1) If the downstream experiment is sensitive to pH or EDTA, you can use sterilized water for elution. The pH value of the eluent has a great influence on the elution efficiency, if you use water as the eluent, you should ensure that the pH value is 7.0-8.5 (you can use NaOH to adjust the pH value of the water to this range), and when the pH value is lower than 7.0, the elution efficiency is not high.2) Incubation at room temperature for 5 minutes prior to centrifugation increases yield.(3) If the final concentration of DNA is to be increased, the DNA eluate obtained in step 10 can be re-added to the adsorbent membrane and repeat step 10; if the elution volume is less than 100µl, the final concentration of DNA can be increased, but it may reduce the total DNA yield. If the amount of DNA obtained is less than 1µg, 50µl Buffer GE is recommended for elution.4) Because DNA stored in water is subject to acidic hydrolysis, for long-term storage, elution with Buffer GE and storage at -20°C are recommended... Read More | Inquire | DescriptionThe Universal Coupling Kit makes particle-based immunoassays, lateral flow tests and biomolecule separation applications more flexible than ever before. It is the only kit that allows users to select and couple their choice of carboxylated particle with their chosen protein.Employing a DescriptionThe Universal Coupling Kit makes particle-based immunoassays, lateral flow tests and biomolecule separation applications more flexible than ever before. It is the only kit that allows users to select and couple their choice of carboxylated particle with their chosen protein.Employing a unique mechanism to immobilise proteins, Anteo′s advantages outweigh those of conventional covalent chemistries such as NHS/EDC or passive binding. This facilitates coupling of antibodies with ease, improved functionality and reproducibility, leading to better uniformity between experiments.Anteo′s Activation Reagent is water-based and replaces the dry chemicals you would use with the traditional NHS/EDC method. Our One-Step-Activation only takes one hour, and improves efficiency in terms of both time and cost. It also provides the ability to either store activated particles up to 12 months for later use, or to immediately couple proteins.Particle-Based Immunoassays, Lateral Flow, Bioseparations and Immunoprecipitation... Read More |