| Description | Lactate dehydrogenase (LDH or LD) is a stable protein present in the cytoplasm of normal cells and normally cannot pass through the cell membrane. When cells are damaged, membrane permeability increases, and LDH is released extracellularly. A decrease in intracellular LDH and an increase in LDH in Lactate dehydrogenase (LDH or LD) is a stable protein present in the cytoplasm of normal cells and normally cannot pass through the cell membrane. When cells are damaged, membrane permeability increases, and LDH is released extracellularly. A decrease in intracellular LDH and an increase in LDH in the culture medium occur. Measuring the LDH activity in the culture medium or the LDH leakage rate can reflect drug-induced cytotoxicity. LDH belongs to the oxidoreductase family and can reversibly catalyze the redox reaction between lactate (L) and pyruvate (P). The reaction formula is: Lactate + NAD⁺ → Pyruvate + NADH + H⁺, where L → P is the forward reaction and P → L is the reverse reaction. Detection Principle: Using NAD⁺ as a hydrogen acceptor, LDH catalyzes the dehydrogenation of lactate to generate pyruvate. Pyruvate then reacts with dinitrophenylhydrazine to form pyruvate dinitrophenylhydrazone, which appears brownish-red in an alkaline solution. The color intensity is proportional to the pyruvate concentration. The absorbance at 440 nm can be measured using a microplate reader. The released LDH activity during cytotoxicity or the LDH activity in other samples can be calculated using formulas. This kit can be used for routine LDH activity detection and is more commonly used for cytotoxicity assays using LDH release as an indicator.This kit is for scientific research use only and is not intended for clinical diagnosis or other purposes.L1501786Component100T500TStorageL1501786ALDH Assay Buffer3 mL15 mL2-8℃. Store in the dark.L1501786BNAD1EA2EA-20℃L1501786CPhenylhydrazine Color Solution3 mL15 mL2-8℃. Store in the dark.L1501786DAlkaline Color Solution10 mL50 mLRT.L1501786ELDH Releasing Agent (10X)2 mL10 mLRT.User-Prepared Instruments and Reagents1. 96-well plate cultured test and control group cell samples, sterile PBS, culture medium, distilled water.2. Microplate centrifuge, 96-well plate or centrifuge, centrifuge tubes, incubator or water bath, microplate reader.Experimental Procedure1. Sample Preparation1.1 LDH Release AssaySeed an appropriate number of cells into a 96-well culture plate based on cell size and growth rate, so that the cell density does not exceed 90% confluency at the time of detection.Aspirate the culture medium, wash once with PBS, add fresh culture medium.Set up corresponding control groups according to experimental needs:Background Blank Control Well A: Culture medium without cells.Sample Control Well B: Control cells without drug treatment.Maximum Enzyme Activity Control Well C: Lysed samples from untreated cells.Drug-treated Sample Well D: Cells treated with the drug.Continue cultivation.Before detection, take out the cell culture plate. Add LDH Releasing Agent (10X) to the "Maximum Enzyme Activity Control Well C" at a volume equal to 10% of the original culture medium volume. Mix thoroughly by pipetting up and down several times. Continue cultivation for about 1 hour.Centrifuge the cell culture plate at 400 g for 5 minutes using a microplate centrifuge.Aspirate 5 µL of supernatant from each well and transfer it to the corresponding wells of a new 96-well plate for subsequent LDH detection.1.2 Cytotoxicity and Cell Proliferation Assay for Intracellular Total LDHSeed an appropriate number of cells into a 96-well culture plate based on cell size and growth rate, so that the cell density does not exceed 90% confluency at the time of detection.Treat with different drugs and set up appropriate controls.Centrifuge the cell culture plate at 400 g for 5 minutes using a microplate centrifuge.Aspirate the culture medium.Add 150 µL of LDH Releasing Agent diluted 10-fold with PBS. Shake the plate to mix thoroughly. Continue cultivation for about 1 hour.Centrifuge the cell culture plate at 400 g for 5 minutes using a microplate centrifuge.Aspirate 5 µL of supernatant from each well and transfer it to the corresponding wells of a new 96-well plate for subsequent cytotoxicity detection.1.3 Protein Concentration DeterminationAfter sample preparation, the protein concentration can be determined using a BCA Protein Assay Kit (Aladdin B665595 BCA Protein Quantification Kit or R1491648 Ready-to-Use BCA Protein Quantification Kit are recommended) to facilitate subsequent calculation of LDH content per unit protein weight in tissues or cells.2. Preparation of NAD SolutionTake one vial of NAD (powder) and dissolve it in 1.5 mL of deionized water.3. LDH Enzymatic ReactionAdd solutions sequentially according to the table below, taking care to avoid bubbles. If the enzyme activity in the sample is too high, reduce the sample volume or dilute appropriately before assay.Reagent (µL)Volume (µL)Test Sample (supernatant)5LDH Assay Buffer25NAD Solution5 Mix well, incubate at 37°C for 15 min. Phenylhydrazine Color Solution25 Mix well, incubate at 37°C for 15 min. Alkaline Color Solution100Distilled Water150 4. LDH Measurement Mix well and let stand at room temperature for 5 minutes. Measure the absorbance of each well at 440 nm using a microplate reader. 5. Result Calculation Cytotoxicity or Mortality Rate (%) = (A D - A B ) / (A C - A B ) × 100% If the absorbance value A γ of a known concentration *c* of an LDH enzyme standard and the absorbance value A γ0 of the standard blank control are measured simultaneously, the enzyme activity in the sample can be roughly calculated:LDH Activity in Test Sample (mU/mL) = (A B - A A ) / (A γ - A γ0 ) × *c* For accurate calculation of the absolute LDH enzyme activity in the sample, use a self-prepared LDH standard to plot a standard curve with the measured absorbance values. The enzyme activity of the sample can be calculated using the formula derived from the standard curve. Where: A A = Absorbance of Background Blank Control Well A A B = Absorbance of Sample Control Well B A C = Absorbance of Maximum Enzyme Activity Control Well C A D = Absorbance of Drug-treated Sample Well D 6. Results and Analysis The cytotoxicity of drugs or toxicants can be determined by directly comparing the LDH activity in each well. Higher LDH activity indicates higher cell membrane permeability and more severe cell damage.Precautions1. Use serum-free or low-serum concentration culture medium when culturing cells to exclude serum interference; otherwise, deviations may occur.2. EDTA inhibits LDH. Avoid using or thoroughly remove reagents containing EDTA during operation.3. Measure LDH as soon as possible after collection. If the collected cell culture medium is stored for too long, LDH activity may decrease.4. Use solutions prepared at the same time for the same batch of experiments. The volume of solutions used and the reaction time should be consistent.5. In the enzymatic reaction, the recommended supernatant sample volume is 2.5-10 µL. If the enzyme activity in the sample is too high, reduce the sample volume or dilute appropriately before assay.6. Measurement should be completed within 15 minutes after color development.7. The Alkaline Color Solution is somewhat corrosive; handle with care.8. Use reagents promptly after opening to avoid affecting subsequent experimental results.9. For your safety and health, please wear a lab coat and disposable gloves during operation... Read More | The aladdin 488 Caspase-3 live cell assay kit contains the aladdin 488 Caspase-3 substrate and the Ac-DEVD-CHO Caspase-3 inhibitor. aladdin 488 Caspase-3 Substrate provides an effective tool for detecting apoptosis based on Caspase-3 activity, suitable for fluorescence microscopy and flow cytometry.The aladdin 488 Caspase-3 live cell assay kit contains the aladdin 488 Caspase-3 substrate and the Ac-DEVD-CHO Caspase-3 inhibitor. aladdin 488 Caspase-3 Substrate provides an effective tool for detecting apoptosis based on Caspase-3 activity, suitable for fluorescence microscopy and flow cytometry. Compared with other fluorescent substrates or fluorescent inhibitors of Caspase based on ( FLICA ) analysis, aladdin 488 Caspase-3 Substrate does not inhibit the apoptosis process of intact cells while detecting Caspase-3 activity. Substrate is composed of fluorescent DNA dyes coupled with Caspase-3 DEVD recognition sequence. Substrate initially had no fluorescence and entered the cytoplasm through the cell membrane. In apoptotic cells, Caspase-3 cleaves the Substrate and releases high-affinity DNA staining, which migrates to the nucleus to label DNA and emits bright green fluorescence.Therefore, aladdin 488 Caspase-3 Substrate is bifunctional, which can not only detect Caspase-3 activity, but also visualize the morphological changes of the nucleus during apoptosis. Aladdin 488 staining can be fixed in formaldehyde and compatible with subsequent immunostaining experiments.Parameters:aladdin 488：Ex/Em = 500/530 nm (with DNA)Component：Points for attention：1.Please instantaneously centrifuge the product to the bottom of the tube before use, and then carry out subsequent experiments. 2.Cells can be co-stained with a final concentration of 1µM Hoechst 33342 dye to produce blue fluorescence staining of the nucleus ( Ex / Em = 346 / 460 nm ). 3.Aladdin 488 staining can be fixed by formaldehyde, but it is not compatible with methanol fixation. 4.Formaldehyde-fixed aladdin 488-stained cells can be treated with 0.1 % TritonX-100 for subsequent staining, but the brightness of the treated staining may be weakened. 5.Fluorescent dyes all have quenching problems, please try to avoid light to slow down the fluorescence quenching. 6.For your safety and health, please wear experimental clothes and wear disposable gloves.Scope of application：Caspase 3 kit and apoptosis detectionUsage:1. Experimental optimization: The experimental steps provided below are based on the endpoint detection system. Aladdin 488 Substrate can also be used for long-term cell incubation course research. Cell density, substrate concentration, and inhibitor concentration may need to be optimized. The optimal substrate concentration may be between 1-10 µ Between M. Cells can be incubated with substrates in culture medium, PBS, or other buffer of your choice. For adherent cells, we recommend replacing them with fresh culture media containing substrates to prevent background heterogeneity. The operation of changing the medium or washing the cells after substrate incubation is freely selectable.2. We suggest that you set the following controls:A. Negative control: cells that do not induce apoptosis;B. Positive control: cells that induce apoptosis;C. Inhibitor control: Induce cell apoptosis while incubating Caspase-3/7 inhibitors (or 10-30 minutes in advance), and finally add Aladdin 488 Caspase-3 substrate.3. The Caspase-3/7 inhibitor Ac-DEVD-CHO in the Ac-DEVD-CHO Caspase-3 inhibitor control kit can be used to confirm that Caspase-3/7 depends on the fluorescence signal of aladdin 488. For inhibitor control, the final concentration of the inhibitor should be at least twice the substrate concentration (e.g. when using 5 µ At substrate M aladdin 488, the concentration of Ac-DEVD-CHO is 10 µ M). Before adding the substrate, incubate Ac-DEVD-CHO at room temperature for 15-30 minutes. After adding the substrate, continue to retain the inhibitor in the incubation solution. Ac-DEVD-CHO is a reversible competitive inhibitor. In certain cell types, effective Caspase-3/7 inhibitors require the use of irreversible inhibitors, such as Z-DEVD-FMK, or the addition of inhibitors before or during apoptosis induction.4. Flow cytometry(1) Choose appropriate methods to induce cell apoptosis, with untreated cell samples as controls.(2) Adhering cells should be digested with trypsin or other methods before performing the aladdin 488 Caspase-3 experiment.(3) Resuspend cells with culture medium or buffer to achieve a cell density of 106 cells/mL(4) Suck 0.2 mL of cell suspension into a flow cytometry test tube.(5) Inhibitor control samples were treated with Ac-DEVD-CHO on cells (see 3 above) Ac-DEVD-CHO Caspase-3 inhibitor control.(6) 200 µ Add 5 to L cell suspension µ Substrate of 0.2 mM and immediately mix to achieve a substrate concentration of 5 µ M. The optimal substrate concentration for different cells may vary and requires analysis and optimization.(7) Incubate cells at room temperature in dark for 15-30 minutes.(8) Join 300 µ L-medium or PBS, analyzed by flow cytometry. Detect the channel for green fluorescence (Ex/Em=485/515 nm).5. Fluorescence microscope(1) Choose appropriate methods to induce cell apoptosis, with untreated cell samples as controls.(2) Inhibitor control samples were treated with Ac-DEVD-CHO on cells (see 3 above) Ac-DEVD-CHO Caspase-3 inhibitor control.(3) Using a solution containing 5 µ M Substrate's fresh culture medium or PBS is used to replace the cell culture medium (see 1 above) Experimental optimization). For the inhibitor control group, the inhibitor was incubated together with the substrate.(4) Incubate cells at room temperature for 30 minutes or longer.(5) Cells can be directly observed in culture media containing Substrate. For the endpoint analysis method, PBS was used to clean the cells, fluorescence microscopy was used to observe the cells, and a filter (Ex/Em=485/515 nm) was used to observe green fluorescence.6. Fluorescence enzyme-linked immunosorbent assay (ELISA) reader(1) Adherent cells grow in black 96 well plates; Suspend cells, adjust the density to 106 cells/mL, and divide 0.2 mL of cell suspension into one well.(2) Choose appropriate methods to induce cell apoptosis, with untreated cell samples as controls. Note: Cells may be processed in tubes or bottles and then transferred to a 96 well detection plate.(3) Inhibitor control samples were treated with Ac-DEVD-CHO on cells (see 3 above) Ac-DEVD-CHO Caspase-3 inhibitor control.(4) For suspended cells, directly add Substrate and mix well. For adherent cells, use a solution containing 5 µ M Substrate's fresh culture medium or PBS is used to replace the cell culture medium (see 1 above) Experimental optimization). For the inhibitor control group, the inhibitor was incubated together with the substrate.(5) Cells can be directly observed in culture media containing Substrate.(6) For suspended cells, gently shake to resuspend the cells. The fluorescence enzyme-linked immunosorbent assay instrument is set with an excitation wavelength of 488 nm and an emission wavelength of 520 nm. Suggest using bottom collection method for adherent cells. Changes in the density of adherent cells may lead to inaccurate readings... Read More | FFPE DNA/RNA KitFixed Tissue DNA/RNA Extraction Kit Catalog number: F666120 (50 preps)Storage conditions: DNase I and 10×Reaction Buffer -20℃, Spin Columns DF and Spin Columns RS can be stored at room temperature for 2 months, 2-8℃ for 1 year, the rest of the components are stored FFPE DNA/RNA KitFixed Tissue DNA/RNA Extraction Kit Catalog number: F666120 (50 preps)Storage conditions: DNase I and 10×Reaction Buffer -20℃, Spin Columns DF and Spin Columns RS can be stored at room temperature for 2 months, 2-8℃ for 1 year, the rest of the components are stored at room temperature (15-30℃).Products Content:Products IntroductionThis kit is suitable for the effective purification of genomic DNA and total RNA from paraffin-embedded tissues, using specially optimized deparaffinizing agents and lysates to release DNA and RNA from tissue section samples, without the use of the organic reagent xylene, and without the need for overnight operation; the digested samples are incubated at higher temperatures to remove inhibitors caused by cross-linking, which can effectively improve nucleic acid yields and purity; and an optimized buffer system allows nucleic acids in the lysate to bind specifically to the adsorbent membrane, and inhibitors are effectively removed by a two-step rinsing procedure. The optimized buffer system enables the nucleic acids in the lysate to bind specifically to the adsorbent membrane, and the inhibitors are effectively removed by a two-step rinsing step, and finally eluted with low-salt buffer or water to obtain high purity DNA and RNA, and at the same time, equipped with a high-efficiency microsorbent column, the volume of the elution can be as low as 20 µl. The purified DNA and RNA can be directly used for PCR, Real-time PCR, SNP genotyping, STR genotyping, and so on. The purified DNA and RNA can be directly used for PCR, Real-time PCR, SNP genotyping, STR genotyping, second-generation sequencing, pharmacogenomics research and blot analysis.Self-contained reagent: anhydrous ethanolPre-experiment Preparation and Important Notes 1. After obtaining the sample, fix the sample as soon as possible, the fixation time of 14-24 hours is appropriate, too long a period of time will easily lead toDNA and RNA breaks, affecting downstream experiments. If the formaldehyde fixation time is too long or the sample is stored for too long(>1 year) is prone to compromise DNA integrity and failure to amplify long fragments.2. Ensure that samples are thoroughly dehydrated prior to embedding; residual formalin will inhibit Proteinase K action.3. Add 1.25 ml of Proteinase K Storage Buffer to Proteinase K to dissolve it, and store at -20℃. Do not leave the prepared Proteinase K at room temperature for a long period of time to avoid affecting its activity.4. Anhydrous ethanol should be added to Buffer RW2, Buffer GW1 and Buffer GW2 according to the label instructions on the vials before first use.5. Check Buffer GTL, Buffer GL and Buffer DS for crystallization or precipitation prior to use; if crystallization or precipitation occurs, redissolve Buffer GTL, Buffer GL and Buffer DS in a 37°C water bath.6. Preheat the water bath or thermostatic mixer to 56°C before starting the experiment.7. Use an ambient temperature centrifuge or set the centrifuge temperature to 25°C. Temperatures below 15°C may result in clogging of the adsorption column.8. To prevent RNase contamination, the following should be observed:1) Use RNase-free plastics and tips to avoid cross-contamination.(2) Glassware should be dry baked at 180°C for 4 hours before use, plasticware can be soaked in 0.5 M NaOH for 10 minutes, rinsed thoroughly with water and autoclaved.3) RNase-free water should be used to prepare the solution.(4) Operators wear disposable masks and gloves, and change gloves diligently during the experiment.procedureParaffin-embedded samples1. Trim off excess paraffin from the tissue block to expose the tissue and cut into 5-10 µm slices.2. Place approximately 1 x 1 cm2 slices (1-5 slices in total) in a centrifuge tube (supplied), add 500 µl of Buffer DS and vortex for 10 s. Briefly centrifuge the sample to the bottom of the tube. Centrifuge briefly to collect the sample at the bottom of the tube, incubate at 56°C for 3 minutes, remove from the water bath and allow to cool to room temperature before proceeding.Note: If the surface of the sample is exposed to air, discard the initial 2-3 slices without using them.3. Centrifuge at 12,000 rpm for 2 minutes and carefully discard the supernatant thoroughly without aspirating the precipitate. The residual dewaxing solution can be carefully removed with a small tip (10 µl).4. Add 180 µl of Buffer GTL and 20 µl of Proteinase K to the above tube and mix well with vortexing.5. Incubate at 56°C for 15 minutes, then place on ice for 3 minutes. Centrifuge at 12,000 rpm for 15 minutes at room temperature.6. Transfer the supernatant to a new 1.5 ml centrifuge tube for RNA extraction, taking care not to aspirate undigested tissue. Use the precipitate for DNA extraction. RNA extraction7. Take the supernatant obtained in step 6 and incubate at 80°C for 15 minutes.8. Add 320 µl of Buffer GL, mix by vortexing and shaking, then add 720 µl of anhydrous ethanol and mix immediately by vortexing and shaking.9. Add all of the resulting solution to the Spin Columns RS in the collection tube; if the solution cannot be added all at once, it may be transferred in several passes. centrifuge the column at 12,000 rpm for 1 minute, pour off the waste solution from the collection tube, and place the column back into the collection tube. Note: If the columns are clogged, the sample size may be too large and consideration should be given to reducing the number of starting sections to 1-2.Optional step: If genomic DNA is to be removed, the following steps can be followeda. Add 350 µl of Buffer RW1 to the column, centrifuge at 12,000 rpm for 1 minute, discard the waste solution, and place the column back into the collection tube.b. Preparation of DNase I mixture: Take 52 µl of RNase-Free Water and add 8 µl of 10×Reaction to it.Buffer and 20 µl DNase I (1 U/µl), mix well, and prepare a final volume of 80 µl of reaction solution.c. Add 80 µl of DNase I Mix directly to the adsorption column and incubate at 20-30°C for 15 minutes.d. Add 350 µl of Buffer RW1 to the column, centrifuge at 12,000 rpm for 1 minute, discard the waste solution, and return the column to the collection tube.Add 500 µl of Buffer RW2 to the adsorbent column, centrifuge at 12,000 rpm for 1 min, pour off the waste liquid in the collection tube, and put the adsorbent column back into the collection tube.11. Repeat step 10. centrifuge at 12,000 rpm for 2 minutes and pour off the waste liquid in the collection tube. Place the column at room temperature for 5 minutes.minutes to dry thoroughly.12. Place the column in a new RNase-free centrifuge tube and add 20-50 µl to the center of the column.RNase-Free Water, left at room temperature for 5 minutes, centrifuged at 12,000 rpm for 1 minute, and collected RNA solution, the-80°C for storage.DNA extraction7. Take the precipitate obtained in step 6 and add 180 µl Buffer GTL and 20 µl Proteinase K to the precipitate. VortexResuspend the precipitate for 15 seconds.8. Incubate at 56°C for 1 hour until the sample is completely dissolved. 90°C for 1 hour.Add 200 µl Buffer GL, vortex and shake to mix and then add 200 µl anhydrous ethanol, vortex and shake to mix thoroughly. Centrifuge briefly so that the solution on the wall of the tube collects at the bottom of the tube. Add all of the solution from step 9 to the Spin Columns DF in the collection tube, or transfer the solution in several passes. centrifuge at 12,000 rpm for 1 minute, pour off the waste solution from the collection tube, and return the column to the 10. collection tube.Note: If the adsorption column is clogged, the sample size may be too large and consideration should be given to reducing the number of starting sections to 1-2.11. Add 500 µl of Buffer GW1 to the adsorbent column and centrifuge at 12,000 rpm for 1 minute. Pour off the waste liquid from the collection tube and put the column back into the collection tube.12. Add 500 µl of Buffer GW2 to the adsorbent column and centrifuge at 12,000 rpm for 1 minute. Pour off the waste liquid from the collection tube and place the column back into the collection tube.Note: Step 12 may be repeated if further purity is required.13. Centrifuge at 12,000 rpm for 2 minutes and pour off the waste liquid in the collection tube. Leave the adsorption column at room temperature for 5 minutes to dry thoroughly. Note: The purpose of this step is to remove residual ethanol from the adsorbent column; ethanol residue will affect the subsequent enzymatic reaction. 14. Place the column in a new 1.5 ml centrifuge tube, add 20-50 µl Buffer EB to the center of the column, leave at room temperature for 5 minutes, centrifuge at 12,000 rpm for 1 minute, collect the DNA solution, and store at -20℃... Read More | Product content: M665559Component50 TStorageM665559ABuffer GTT15 mLRTM665559BBuffer GL15 mLRTM665559CBuffer GW1（concentrate）13 mLRTM665559DBuffer GW2（concentrate）15 mLRTM665559EBuffer GE15 mLRTM665559FProteinase K1.25 mLRTM665559GSpin CoLumns DM with CoLLection Tubes50 Product content: M665559Component50 TStorageM665559ABuffer GTT15 mLRTM665559BBuffer GL15 mLRTM665559CBuffer GW1（concentrate）13 mLRTM665559DBuffer GW2（concentrate）15 mLRTM665559EBuffer GE15 mLRTM665559FProteinase K1.25 mLRTM665559GSpin CoLumns DM with CoLLection Tubes50 EART Product Introduction:This reagent kit is suitable for extracting high-purity total DNA from fresh or frozen mouse or rat tails. The method provided by this reagent kit is simple and feasible, and the purification process does not require phenol or chloroform extraction. It can obtain DNA fragments up to 50 kb, and can also effectively recover fragments of 100 bp. This reagent kit uses a unique lysis solution to effectively lyse mouse tail samples. The optimized buffer system efficiently binds the DNA generated after the lysis of mouse tail to the silica matrix adsorption column, while other pollutants can flow through the membrane; Inhibitors of PCR and other enzymatic reactions can be effectively removed through a two-step washing process, followed by washing with low salt buffer or water to obtain high-purity DNA. The purified DNA can be directly used for downstream experiments such as enzyme digestion, PCR, ReaL Time PCR, library construction, Southern BLot, and molecular labeling.Self prepared reagent: anhydrous ethanol.Preparation and important precautions before the experiment:1. Samples should avoid repeated freeze-thaw cycles, otherwise it may result in smaller extracted DNA fragments and a decrease in extraction volume.2.Before the first use, anhydrous ethanol should be added to BufferGW1 and BufferGW2 according to the instructions on the reagent bottle label.3. Before use, please check if there is any crystallization or precipitation in the Buffer GL. If there is any crystallization or precipitation, please dissolve the Buffer GL again in a 56 ℃ water bath.Operation steps:1. Take a tail of a rat or two mice with a length of 0.4-0.6 cm, grind it into fine powder in liquid nitrogen or cut it into pieces and place it in a centrifuge tube (provided by oneself). Join 180 µ L Buffer GTT, shake and mix well. Note: Ensure that the starting quantity of the organization does not exceed the recommended range.2. Add 20 µ L Protein K, vortex oscillation, thoroughly mix.3. Place in a 56 ℃ water bath until the tissue solution is completely clear. Generally, digestion is required for 6-8 hours. During the incubation process, vortex oscillation is required to evenly disperse the sample. Note: 1) If there is still gel like substance after incubation and vortex oscillation, digest overnight or add 20 more if necessary µ L Protein K digestion will not affect subsequent operations. 2) To remove RNA, add 4 after completing the above steps µ L 100 mg/mL RNase A solution, shake well and let stand at room temperature for 5-10 minutes.4.12000 rpm (~13400 × g) for 1 minute to remove undigested tissues similar to mouse hair. Transfer the supernatant to a new centrifuge tube (provided by oneself).5. Add 200 µ L Buffer GL, vortex oscillation, thoroughly mixed. Join 200 µ L anhydrous ethanol, vortex and shake, thoroughly mix. Short centrifugation allows the solution on the tube wall to be collected to the bottom of the tube.Attention: 1) After adding Buffer GL and anhydrous ethanol, immediately vortex and shake to mix well.2) If multiple samples are operated together, Buffer GL and anhydrous ethanol can be mixed in equal proportions and added to the samples together.3) The addition of Buffer GL and anhydrous ethanol may produce white precipitates, which will not affect subsequent experiments.6. Add all the solutions obtained in step 5 to the adsorption column (Spin CoLumins DM) that has been loaded into the collection tube. If the solution cannot be added at once, it can be transferred multiple times. Centrifuge at 12000 rpm for 1 minute, discard the waste liquid in the collection tube, and place the adsorption column back into the collection tube.7. Add 500 to the adsorption column µ L Buffer GW1 (check if anhydrous ethanol has been added before use), centrifuge at 12000 rpm for 1 minute, discard the waste liquid in the collection tube, and place the adsorption column back into the collection tube.8. Add 500 to the adsorption column µ L Buffer GW2 (check if anhydrous ethanol has been added before use), centrifuge at 12000 rpm for 1 minute, discard the waste liquid in the collection tube, and place the adsorption column back into the collection tube.Note: To further improve DNA purity, repeat step 8.9.12000 rpm for 2 minutes and discard the waste liquid from the collection tube. Place the adsorption column at room temperature for a few minutes to thoroughly air dry. Note: The purpose of this step is to remove residual ethanol from the adsorption column, which will affect subsequent enzymatic reactions (such as enzyme digestion, PCR, etc.).10. Place the adsorption column in a new centrifuge tube (provided by oneself) and add 50-200 to the middle of the adsorption column in the air µ L Buffer GE or sterilized water, leave at room temperature for 2-5 minutes, centrifuge at 12000 rpm for 1 minute, collect DNA solution, and store DNA at -20 ℃.Note: 1) If downstream experiments are sensitive to pH or EDTA, they can be washed off with sterilized water. The pH value of the eluent has a significant impact on the elution efficiency. If water is used as the eluent, its pH value should be ensured to be between 7.0-8.5 (NaOH can be used to adjust the pH value of the water to this range). When the pH value is below 7.0, the elution efficiency is not high.2) Incubating at room temperature for 5 minutes before centrifugation can increase yield.3) Use an additional 50-200 µ Re washing with L Buffer GE or sterilized water can increase yield.4) If you want to increase the final concentration of DNA, you can add the DNA eluent obtained in step 10 back onto the adsorption membrane and repeat step 10; If the elution volume is less than 200 µ L. It is possible to increase the final concentration of DNA, but it may reduce the total yield. If the amount of DNA is less than 1 µ g. Recommended 50 µ L Buffer GE or off... Read More | R669988 Component 50T Storage R669988A DNase I 1000 U -20℃. Avoid freeze/thaw cycle. R669988B 10×Reaction Buffer 1000 µL -20℃. Avoid freeze/thaw cycle. R669988C Buffer RL 35 mL RT R669988D Buffer RLC 35 mL RT R669988E Buffer RW1 40 mL RT R669988F Buffer RW2 (concentrate) 11 mL R669988 Component 50T Storage R669988A DNase I 1000 U -20℃. Avoid freeze/thaw cycle. R669988B 10×Reaction Buffer 1000 µL -20℃. Avoid freeze/thaw cycle. R669988C Buffer RL 35 mL RT R669988D Buffer RLC 35 mL RT R669988E Buffer RW1 40 mL RT R669988F Buffer RW2 (concentrate) 11 mL RT R669988G RNase-Free Water 10 mL RT R669988H Spin Columns FL with Collection Tubes 50 sets RT R669988I Spin Columns RM with Collection Tubes 50 sets RT R669988J RNase-Free Centrifuge Tubes (1.5 mL) 50 EA RTProductsThis kit is used for the extraction and purification of high-quality total RNA from a variety of plants, and is also suitable for the extraction of fungal mycelial RNA. The unique separation column is used for homogenization and filtration of high viscosity plant or fungal lysates, while the silicon matrix membrane is used to adsorb the RNA for purification, so that various contaminants, such as polysaccharides, are effectively removed by washing, and the eluted RNA can be directly used in various downstream experiments. The molecular weight of RNA extracted by this kit is more than 200 bases, with high purity and almost no DNA residue. For RNA experiments that are very sensitive to trace DNA, the residual DNA can be removed by digestion on a column using RNase-free DNase. The extracted RNA can be used in Northern Blot, Dot Blot, RT-PCR and in vitro translation experiments.Self-contained reagents: β-mercaptoethanol, anhydrous ethanol (freshly opened or for RNA extraction).Pre-experiment Preparation and Important Notes1. To prevent RNase contamination, attention should be paid to the following aspects:1) Use RNase-free plastics and tips to avoid cross-contamination.2) RNase-free water should be used to prepare the solution.(3) Operators wear disposable masks and gloves, and change gloves diligently during the experiment.2. To prevent RNase contamination, attention should be paid to the following aspects:1) Use RNase-free plastics and tips to avoid cross-contamination.(2) Glassware should be dry-roasted at 180°C for 4 hours before use, and plasticware can be soaked in 0.5M NaOH for 10 minutes, rinsed thoroughly with water and autoclaved.3) RNase-free water should be used to prepare the solution.(4) Operators wear disposable masks and gloves, and change gloves diligently during the experiment.3. Avoid repeated freezing and thawing of the extracted samples, otherwise it will affect the amount and quality of RNA extraction.4. Please add β-mercaptoethanol to Buffer RL before use, add 10µl of β-mercaptoethanol to 1ml of Buffer RL, it can be stored for 1 month at room temperature. Buffer RL with β-mercaptoethanol can be stored at room temperature for 1 month. β-mercaptoethanol is not required for use of Buffer RLC.5. Anhydrous ethanol should be added to Buffer RW2 before first use according to the instructions on the reagent bottle label.6. If precipitation occurs in Buffer RL and Buffer RLC, heat to dissolve and leave at room temperature.7. All centrifugation steps are carried out at room temperature and all steps are performed quickly. Procedure1. 50-100 mg of plant tissue is quickly ground to a powder in liquid nitrogen and added to 600 µl of Buffer RL (check for addition of β-mercaptoethanol before use) or Buffer RLC. vortexing and oscillating to allow for adequate lysis.Note: 1) The main component of Buffer RL is guanidine isothiocyanate, which is suitable for lysis of most plant tissues. However, in some plant tissues (e.g. endosperm of corn), due to the special secondary metabolites, guanidine isothiocyanate causes precipitation of the sample, resulting in poor RNA extraction, in this case, Buffer RLC can be added instead of Buffer RL.2) Incubation at 56°C for 1-3 minutes helps tissue lysis, but do not incubate at high temperatures for plants with high starch content.2. Transfer all the liquid obtained in step 1 to an adsorption column (Spin Columns FL) that has been loaded into a collection tube, centrifuge at 12,000 rpm (~13,400 x g) for 2 minutes, and transfer the supernatant from the collection tube to a new centrifuge tube (supplied).Note: 1) The tip of the tip of the gun can be cut off when aspirating liquids to facilitate sampling.2) Spin Columns FL removes most of the debris, but a small portion will still flow out and a precipitate will form in the collection tube after centrifugation, so be careful to avoid aspirating the precipitate when proceeding to the next step.3. Add 0.5 times the volume of anhydrous ethanol to the clean lysate obtained in step 2 and mix rapidly.Note: Precipitation may occur upon addition of ethanol, but does not affect subsequent tests.4. Transfer the solution obtained in the previous step to the Spin Columns RM in the collection tube. If it is not possible to add all of the solution to the column at one time, centrifuge the column at 12,000 rpm for 15 seconds in two batches, discard the waste solution and put the column back into the collection tube.5. Add 350 µl Buffer RW1 to the adsorbent column, centrifuge at 12,000 rpm for 1 min, discard the waste liquid and put the adsorbent column back into the collection tube.6. Preparation of DNase I mixture: Take 52µl of RNase-Free Water, add 8µl of 10×Reaction Buffer and 20µl of DNase I (1U/µl) to it, mix well, and make a final volume of 80µl of reaction solution.7. Add 80µl of DNase I mixture directly to the adsorption column and incubate at 20-30°C for 15 minutes.8. Add 350 µl of Buffer RW1 to the adsorption column, centrifuge at 12,000 rpm for 1 minute, discard the waste liquid and put the column back into the collection tube.9. Add 500 µl of Buffer RW2 to the column (check that anhydrous ethanol is added before use), centrifuge at 12,000 rpm for 15 seconds, and discard the waste solution.10. Repeat step 9.11. Place the adsorbent column back into the collection tube, centrifuge at 12,000 rpm for 1 minute, and allow the column to come to room temperature for a few minutes to thoroughly dry out the anhydrous ethanol in the adsorbent column.Note: The purpose of this step is to remove residual ethanol from the adsorption column; ethanol residue can interfere with subsequent enzymatic reactions (zymography, PCR, etc.).12. Load the adsorption column into a new centrifuge tube, add 30-50 µl of RNase-Free Water to the middle of the adsorbent membrane, leave it at room temperature for 1 minute, centrifuge at 12,000 rpm for 1 minute, and store the resulting RNA solution at -70°C to prevent degradation.Note: 1) The volume of RNase-Free Water should not be less than 30 µl, too small volume affects the recovery rate.2) If you want to increase the RNA yield, repeat step 12 with 30-50 µl of fresh RNase-Free Water.3) If the RNA concentration is to be increased, the resulting solution can be reintroduced into the adsorption column and step 12 repeated... Read More |