| Description | Inquire | Inquire | H665581 Component 100 T Storage H665581A gDNA Eraser 50 µL -20℃. Avoid freeze/thaw cycle. H665581B 10×gDNA Eraser Buffer 120 µL -20℃. Avoid freeze/thaw cycle. H665581C HiFiScript, 200 U/µL 100 µL -20℃. Avoid freeze/thaw cycle. H665581D 5×ScriptRT H665581 Component 100 T Storage H665581A gDNA Eraser 50 µL -20℃. Avoid freeze/thaw cycle. H665581B 10×gDNA Eraser Buffer 120 µL -20℃. Avoid freeze/thaw cycle. H665581C HiFiScript, 200 U/µL 100 µL -20℃. Avoid freeze/thaw cycle. H665581D 5×ScriptRT Buffer 500 µL -20℃. Avoid freeze/thaw cycle. H665581E Primer Mix 120 µL -20℃. Avoid freeze/thaw cycle. H665581F RNase-Free Water 2×1 mL -20℃. Avoid freeze/thaw cycle.Product IntroductionThis product is a kit for removing genomic DNA for reverse transcription. The kit removes genomic DNA in 2 minutes at 42°C. Since the reverse transcription reagent contains a component that inhibits gDNA Eraser, cDNA can be synthesized directly by reverse transcription of gDNA Eraser-treated samples.The kit is equipped with a new high-efficiency reverse transcription enzyme, HiFiScript, with novel mutation sites that dramatically increase the transcriptional activity of the enzyme, resulting in higher efficiency and yield of cDNA first-strand synthesis. The first strand of cDNA can be synthesized with higher efficiency and yield, and the first strand of cDNA can be synthesized from pg total RNA or mRNA. If the reverse transcription product cDNA is used for downstream fluorescence quantitative detection, the reverse transcription reaction can be completed at 42℃ in 15 minutes. This kit is suitable for the synthesis of first-strand cDNA and subsequent RT-PCR, RT-qPCR, and the construction of full-length cDNA libraries.Product Features1. Rapid genome removal: contains gDNA Eraser for genomic DNA removal, which removes genomic DNA in just 2 minutes.2. Rapid reverse transcription: 15 minutes to obtain fluorescent quantitative PCR template cDNA first strand synthesis.3. High sensitivity: cDNA first strand can be synthesized using pg-level total RNA or mRNA templates.4. Highly efficient reverse transcription: Novel mutation sites dramatically increase enzyme activity, resulting in higher yields of cDNA.matters needing attention1. During operation, RNase contamination should be avoided to prevent RNA degradation or cross-contamination in the experiment. It is recommended that operators wear masks and disposable gloves and change the gloves frequently, and use specialized instruments and consumables.2. The reverse transcription system is prepared and operated on ice to prevent degradation of RNA. Store the kit enzymes at -20ºC as soon as possible after use and try to avoid repeated freezing and thawing.3. The reaction system can be scaled up to a maximum of 1 µg of total RNA in 10 µl of reaction system.4. Primer Mix is prepared by Oligo(dT) and Random primer, and Oligo-dT Primer or Gene Specific Primer can also be used according to the experimental needs.5. If the amount of starting RNA is less than 50ng, it is recommended to add RNAase inhibitor (RNasin).6. For RNA templates with complex secondary structures, it is recommended to incubate the template RNA at 65°C for 5 minutes immediately on ice prior to the manipulation step and centrifuge briefly before proceeding to the next step.UsageThaw template RNA on ice; place kit components on ice immediately after thawing at room temperature. Each solution was mixed by vortexing and shaking before use and briefly centrifuged.I. Genomic DNA removal reactions1. Prepare the reaction system according to the following table on ice in a total volume of 10 µl. To ensure the accuracy of the reaction solution preparation, prepare the premixed system in the amount of reaction number + 2 before dispensing it into each reaction tube and finally adding the RNA sample.Note: 1) If the amount of total RNA is greater than 1µg, scale up the reaction system proportionally. If the amount of starting RNA is less than 50ng, it is recommended to add RNAase inhibitor (RNasin).2. Mix by vortex shaking and centrifuge briefly so that the solution on the walls of the tube collects at the bottom.3. Incubate at 42°C for 2 minutes (this can be extended to 30 minutes for room temperature reactions).4．At the end of the reaction, centrifuge briefly and place on ice to cool.II. Reverse transcription reaction1. Prepare the reaction system on ice according to the following table. In order to ensure the accuracy of the reaction solution configuration, first prepare a premixed solution in the amount of number + 2, and then dispense 10 µl into each reaction tube, take 10 µl of the prepared premixed solution and add it to the reaction tube of step 1 where the de-etching of the genome has been completed.Note: 1) Oligo-dT Primer or Gene Specific Primer can be used according to the needs of the experiment, it is recommended to use 50 pmol of Oligo-dT Primer or 2 pmol of Gene Specific Primer for 20 µl reaction system.2. Mix well and centrifuge briefly so that the solution on the walls of the tube collects at the bottom.3. cDNA synthesis reaction conditions:1) If fluorescent quantitative PCR assay is performed downstream, incubate at 42°C for 15 minutes and 85°C for 5 minutes.2) If downstream for normal PCR assay, incubate at 42°C for 30-50 minutes and 85°C for 5 minutes. Note: For templates with complex secondary structure or high GC content, the reverse transcription temperature can be increased to 50°C to enhance reverse transcription efficiency.4. At the end of the reaction, centrifuge briefly and place on ice before proceeding with subsequent PCR or fluorescence quantitative PCR, or place at -20°C if prolonged storage is required.Note: When performing Real-time PCR reactions, the amount of reverse transcription product added should not exceed 1/10 of the total volume of the PCR reaction... Read More | This reagent kit is designed based on the principle that biotin and Streptavidin have a strong affinity. After the primary antibody of rabbit or mouse origin binds to the corresponding target antigen, the biotinylated antibody in this kit • • Rabbit/mouse universal secondary antibody This reagent kit is designed based on the principle that biotin and Streptavidin have a strong affinity. After the primary antibody of rabbit or mouse origin binds to the corresponding target antigen, the biotinylated antibody in this kit • • Rabbit/mouse universal secondary antibody specifically binds to the primary antibody; The biotin labeled on the secondary antibody binds to streptavidin labeled with peroxidase (HRP), forming an antigen-specific primary antibody biotinylated secondary antibody streptavidin complex labeled with HRP. HRP can catalyze substrate colorimetry, thereby inferring the presence and distribution of the tested antigen. The biotinylated secondary antibody and SA-HRP used in this reagent kit all adopt optimized labeling and purification techniques, which make their staining more sensitive and have a lower background. They are suitable for detecting formalin fixed paraffin embedded tissue sections, as well as frozen sections, cell slides, freshly prepared blood smears, etc. The rabbit/mouse universal Streptavidin HRP kit is suitable for use with aladdin ready to use or concentrated antibodies. Composition：Note: This reagent kit is only suitable for IHC experiments where the primary antibody is an immune or mouse derived antibodNotes:1. Add 1 drop (approximately 50) to each slice µ l) Calculation: 3ml can make 60 slices, and 18ml can make 360 slices.2.For tissues with abundant endogenous biotin content, it is best to use endogenous biotin blockers for blocking when using this kit.3. DAB working solution is prepared and used immediately, and the prepared working solution is effective within 1 hour in the dark at 2-8 ° C.4. During the experiment, avoid drying the tissue slices, so the amount of working fluid used during each incubation step must be sufficient to ensure complete coverage of the tissue sample, and incubation should be carried out in a wet box as much as possible.5. To obtain the best experimental results, please make sure to optimize the experimental conditions and reagent dosage.6. DAB is a suspected carcinogen, please take necessary protective measures when using it. 7. This product is only for scientific research and cannot be used for human reactions or treatments.Operation steps：1. Routine processing of samples such as paraffin or frozen tissue sections or cell slides to be tested.1) Preparation for staining of tissue sections or cell slides: a. Dewaxing and hydration of paraffin sections: bake at 60 º C for 1 hour, dewaxing twice with xylene for 5 minutes each time; Then immerse in gradient ethanol (anhydrous ethanol anhydrous ethanol 95% 85% 75% ethanol) and distilled water for 5 minutes each for hydration. b. Frozen sections and cell climbing sections (or climbing sections) were soaked in 0.01 M pH 7.4 PBS and washed 3 times for 5 minutes. Then cover the tissue (or cells) with 0.1% Triton X-100 and infiltrate for 15 minutes. Wash twice with 0.01 M pH 7.4 PBS for 5 minutes.2) Antigen repair of paraffin sections: In most cases, high-pressure repair with citric acid buffer is suitable for paraffin tissue sections. Preparation of repair solution: Add 10 ml of citric acid buffer (IHC antigen repair solution, 100 x) to 1 L of deionized water, and mix well. Repair process: The repair solution is added to a high-pressure cooker, and the repaired slices are immersed in the repair solution (must have no tissue). Cover the pressure cooker cover, heat until evenly sprayed with steam, and start timing from the spraying. After 1-2 minutes, the pressure cooker leaves the heat source and cools naturally to room temperature. Remove the slices, rinse with distilled water, and rinse twice with PBS (0.01 M pH 7.4) for 3 minutes each time.2. Add an appropriate amount of Solution A white solution, which is an endogenous peroxidase blocking solution, and incubate at room temperature for 10 minutes, then rinse thoroughly with PBS.3. Add an appropriate amount of Solution B white solution dropwise, which is sealed with normal sheep serum working solution. Incubate at room temperature for 10 minutes and shake dry.4. Add an appropriate amount of primary antibody working solution (commercial ready to use antibodies or concentrated antibodies diluted in appropriate proportions) dropwise, incubate according to experimental requirements, and then rinse thoroughly with PBS.5. Add an appropriate amount of Solution C yellow solution, namely biotin labeled sheep anti rabbit/mouse secondary antibody working solution, incubate at room temperature for 10 minutes, and rinse thoroughly with PBS.6. Add an appropriate amount of Solution D red solution, which is HRP labeled streptavidin. Incubate at room temperature for 10 minutes and rinse thoroughly with PBS.7. Preparation of DAB color working solution: According to the required amount, mix DAB-A and DAB-B in a volume ratio of 1:19 to obtain DAB color working solution. Alternatively, one drop (approximately 50) can be added per milliliter of reagent B µ l) Reagent A, mix well.8. Color development: Add an appropriate amount of DAB color development working solution to the tissue section or cell slide that needs to be developed, and the color development time is generally 1-5 minutes. Observe and control the color development time under a microscope. When the optimal color development effect is achieved, rinse with tap water to terminate the color development. The colored slices are re stained, dehydrated and transparent, and can be stored for a long time after sealing... Read More | V669947 Component 50T Storage V669947A Buffer GL 15 mL RT V669947B Buffer GW1 (concentrate) 13 mL RT V669947C Buffer GW2 (concentrate) 15 mL RT V669947D Buffer RE 10 mL RT V669947E Proteinase K 12.5 mg RT V669947F Proteinase K Storage Buffer 1.25 mL RT V669947G Spin Columns RS with Collection Tubes V669947 Component 50T Storage V669947A Buffer GL 15 mL RT V669947B Buffer GW1 (concentrate) 13 mL RT V669947C Buffer GW2 (concentrate) 15 mL RT V669947D Buffer RE 10 mL RT V669947E Proteinase K 12.5 mg RT V669947F Proteinase K Storage Buffer 1.25 mL RT V669947G Spin Columns RS with Collection Tubes 50 RT V669947H RNase-Free Centrifuge Tubes (1.5 mL) 50 RTProductsThis kit is suitable for the extraction of viral RNA and DNA from fresh or frozen plasma, serum and cell-free body fluids. It is easy to operate as it does not require the use of organic solvents such as phenol and chloroform for extraction. The kit uses a unique buffer system to enable efficient and specific binding of viral nucleic acids in lysate to silica gel centrifugal adsorption columns. Inhibitors of PCR and enzyme reactions as well as residual impurities can be efficiently removed in a two-step effective rinsing step, and finally high purity viral nucleic acids can be obtained by using a low-salt buffer or water for elution. The purified viral nucleic acid is free of protein, nuclease and other impurities, and can be used directly in PCR, RT-PCR, Real-Time PCR, blotting experiments and so on.Self-contained reagent: anhydrous ethanol.Pre-experiment and Important Notes1. Add 1.25ml Proteinase K Storage Buffer to Proteinase K to dissolve it and store it at -20℃. Do not leave the prepared Proteinase K at room temperature for a long time, and avoid repeated freezing and thawing to avoid affecting its activity. Do not add Proteinase K directly into Buffer GL.2. Repeated freezing and thawing of the sample should be avoided, as this may result in smaller DNA fragments and a decrease in the amount of extracted DNA.3. Avoid repeated freezing and thawing of serum or plasma, which can lead to protein denaturation or precipitation, reducing the viral titer and thus affecting the yield of extracted viral nucleic acids.4. Anhydrous ethanol should be added to Buffer GW1 and Buffer GW2 according to the label instructions of the reagent bottle before first use.5. Check Buffer GL for crystallization or precipitation before use. If crystallization or precipitation occurs, redissolve Buffer GL in a water bath at 56℃.Procedure1. Take a 1.5 ml centrifuge tube (self-provided) and add 20 µl Proteinase K.2. Add 200 µl serum or plasma to the centrifuge tube. Add 200µl Buffer GL and vortex and shake for 15 seconds.Note: 1) Sample volume less than 200 µl can be made up by adding 0.9% NaCl (self-provided). 2) In order to ensure effective lysis of the sample, the sample needs to be mixed well with Buffer GL after adding Buffer GL.3. Incubate at 56°C for 15 minutes, centrifuge briefly, and collect the solution from the wall of the tube to the bottom of the tube.4. 250 µl of anhydrous ethanol was added, vortexed and shaken for 15 seconds, left at room temperature for 5 minutes, centrifuged briefly, and the solution on the wall of the tube was collected at the bottom of the tube.Note: If the ambient temperature exceeds 25°C, anhydrous ethanol should be used after pre-cooling on ice.5. Add the solution obtained in step 4 to the adsorbent column (RNase-Free Columns RS) that has been loaded into the collection tube, and if the solution cannot be added at one time, it can be transferred in several times. centrifuge the column at 12,000 rpm (~13,400 × g) for 1 min, pour off the waste liquid in the collection tube, and put the column back into the collection tube.6. Add 500 µl of Buffer GW1 to the adsorption column (check that anhydrous ethanol has been added before use), centrifuge at 12,000 rpm for 1 minute, pour off the waste liquid in the collection tube, and put the adsorption column back into the collection tube.7. Add 500 µl of Buffer GW2 to the adsorption column (check that anhydrous ethanol has been added before use), centrifuge at 12,000 rpm for 1 minute, pour off the waste liquid in the collection tube, and put the adsorption column back into the collection tube.Note: Step 7 can be repeated if further DNA purity is required.8. Add 500 µl of anhydrous ethanol to the adsorbent column and centrifuge at 12,000 rpm for 1 min. Pour off the waste liquid in the collection tube and put the adsorbent column back into the collection tube.9. Centrifuge at 12,000 rpm for 3 minutes and pour off the waste liquid in the collection tube. Leave the adsorption column at room temperature for several minutes to dry thoroughly.Note: The purpose of this step is the removal of residual ethanol from the adsorbent column; ethanol residue can interfere with subsequent enzymatic reactions (digestion, PCR, etc.).10. Place the adsorption column in a new collection tube (RNase-Free Centrifuge Tube), add 20-150 µl of Buffer RE or sterilized water overhanging the middle of the adsorption column membrane, leave it at room temperature for 2-5 minutes, and then centrifuge it at 12,000 rpm for 1 minute to collect the nucleic acid solution.Note: 1) If the downstream experiment is sensitive to pH or EDTA, you can use sterilized water for elution. The pH of the eluent has a great influence on the elution efficiency, if water is used as the eluent it should be ensured that its pH is 7.0-8.5 (the pH of water can be adjusted to this range with NaOH), and the elution efficiency is not high when the pH is lower than 7.0.(2) For long-term storage, please store the DNA solution at -20℃ and the RNA solution at -70℃.3) If the final concentration of DNA/RNA is to be increased, the DNA/RNA eluate obtained in step 10 can be re-spiked onto the adsorbent membrane and step 10 repeated... Read More |