| Description | IntroductionCreatine Kinase (CK) is primarily found in tissues such as the heart, muscle, and brain. It reversibly catalyzes the transphosphorylation reaction between creatine and ATP, playing a vital role in energy transfer, muscle contraction, and ATP regeneration. It is a crucial clinical IntroductionCreatine Kinase (CK) is primarily found in tissues such as the heart, muscle, and brain. It reversibly catalyzes the transphosphorylation reaction between creatine and ATP, playing a vital role in energy transfer, muscle contraction, and ATP regeneration. It is a crucial clinical indicator for diagnosing heart and brain diseases.Assay PrincipleCK catalyzes the conversion of Phosphocreatine and ADP to Creatine and ATP. Hexokinase then catalyzes the reaction of ATP with Glucose to form Glucose-6-Phosphate (G6P). Subsequently, Glucose-6-Phosphate Dehydrogenase (G6PDH) catalyzes the oxidation of G6P with NADP⁺ to generate NADPH, leading to an increase in absorbance at 340 nm.Component50TStorageExtraction Buffer60 mL2-8℃Reagent 11EA2-8℃. Store in the dark.Reagent 215 mL2-8℃Reagent 1: Powder in one bottle. Store at 4°C protected from light. Dissolve in 15 mL distilled water before use.Working Solution: Prepare immediately before use by mixing the dissolved Reagent 1 and Reagent 2 at a 1:1 ratio. Incubate the Working Solution at 37°C for 2 minutes prior to use.Required Materials and Equipment (Not Provided)Balance, refrigerated centrifuge, constant temperature water bath, UV spectrophotometer, 1 ml quartz cuvette, and distilled water.Crude Enzyme Extraction:Tissue Samples: Homogenize the tissue on ice in Extraction Buffer at a ratio of 1:5-10 (w/v) (e.g., weigh ~0.1g tissue, add 1 mL Extraction Buffer). Centrifuge the homogenate at 10,000 g, 4°C for 15 min. Collect the supernatant and keep it on ice for assay.Serum Samples: Assay directly.Assay Procedure:Preheat the UV spectrophotometer for at least 30 minutes. Set the wavelength to 340 nm. Zero the instrument with distilled water.In a 1 ml quartz cuvette, add:200 µl sample300 µl distilled water500 µl pre-warmed (37°C) Working SolutionMix thoroughly and immediately record the initial absorbance (A₁) at 340 nm. Record the absorbance again (A₂) after exactly 1 minute at 37°C. Calculate ΔA = A₂ - A₁.CK Enzyme Activity Calculation:General Parameters:ε (NADPH molar extinction coefficient) = 6220 L/mol/cmd (Cuvette light path) = 1.0 cmVₜₒₜₐₗ (Total reaction volume) = 1.0 mL (1000 µL)Vₛₐₘₚₗₑ (Sample volume in reaction) = 0.2 mL (200 µL)T (Reaction time) = 1 minCpr (Sample protein concentration, mg/mL)W (Sample mass, g)Vₛₐₘₚₗₑₜₒₜₐₗ (Total extract volume) = Assumed 1 mL for tissue calculations1. Based on Tissue Protein Content:Definition: One unit of activity is defined as the amount of enzyme that generates 1 nmol of NADPH per minute per mg of protein at 37°C, pH 7.0.Calculation:CK Activity (nmol/min/mg prot) = [ΔA / (ε × d)] × Vₜₒₜₐₗ ÷ (Vₛₐₘₚₗₑ × Cpr) ÷ TSimplified Formula: CK (nmol/min/mg prot) = 804 × ΔA ÷ Cpr2. Based on Tissue Sample Mass:Definition: One unit of activity is defined as the amount of enzyme that generates 1 nmol of NADPH per minute per gram of fresh tissue at 37°C, pH 7.0.Calculation:CK Activity (nmol/min/g fresh weight) = [ΔA / (ε × d)] × Vₜₒₜₐₗ ÷ (Vₛₐₘₚₗₑ / Vₛₐₘₚₗₑₜₒₜₐₗ × W) ÷ TSimplified Formula: CK (nmol/min/g fresh weight) = 804 × ΔA ÷ W3. Based on Serum:Definition: One unit of activity is defined as the amount of enzyme that generates 1 nmol of NADPH per minute per liter of serum at 37°C, pH 7.0.Calculation:CK Activity (nmol/min/L) = [ΔA / (ε × d)] × Vₜₒₜₐₗ ÷ Vₛₐₘₚₗₑ ÷ TSimplified Formula: CK (nmol/min/L) = 804 × ΔANotesBefore the formal assay, it is essential to perform a pilot test with 2-3 samples expected to have significant differences in activity.The prepared Working Solution is stable at 4°C for 7 days. However, it is recommended to use it as soon as possible after preparation.CK in serum is unstable. Determine the activity as soon as possible after sample collection. It can be stored protected from light at 4°C for up to 24 hours.Sample protein content needs to be determined separately. A BCA Protein Assay Kit can be used for this purpose.If the absorbance value (ΔA) is greater than 0.5, dilute the sample appropriately with Extraction Buffer and account for the dilution factor (D) in the calculation formulas (e.g., 804 × ΔA × D ÷ Cpr)... Read More | Product Content D669986Component50 TStorageD669986ABuffer SA15 mLRTD669986B2×PCR MasterMix1 mL-20℃. Avoid freeze/thaw cycle.D669986CProteinase K12.5 mgRTD669986DProteinase K Storage Buffer1.25 mLRTProductsThis kit adopts a unique buffer system containing all the reagents for rapid Product Content D669986Component50 TStorageD669986ABuffer SA15 mLRTD669986B2×PCR MasterMix1 mL-20℃. Avoid freeze/thaw cycle.D669986CProteinase K12.5 mgRTD669986DProteinase K Storage Buffer1.25 mLRTProductsThis kit adopts a unique buffer system containing all the reagents for rapid preparation of genomic DNA and PCR amplification, and is suitable for one-step extraction of genomic DNA from various plant and animal tissues and bacteria and for PCR amplification. The whole extraction process does not require liquid nitrogen grinding, organic solvent extraction, anhydrous ethanol precipitation, and the quality of extracted DNA is stable. The 2×PCR MasterMix provided in this kit is a highly compatible PCR reagent that can amplify DNA samples efficiently and specifically, which includes DNA polymerase, dNTPs, MgCl2, reaction buffer, PCR reaction enhancer and so on. It is characterized by fast and easy, high sensitivity, high specificity, good stability, etc. It is especially suitable for high throughput screening.Pre-experiment Preparation and Important Notes1. Add the specified amount of Proteinase K Storage Buffer to Proteinase K to dissolve it and store it at -20℃. Do not leave the prepared Proteinase K at room temperature for a long time, and avoid repeated freezing and thawing to avoid affecting its activity.2. Repeated freezing and thawing of the samples should be avoided, as this will result in smaller DNA fragments and a decrease in the amount of extracted DNA.3. Before use, please check Buffer SA for crystallization or precipitation. If crystallization or precipitation occurs, please re-dissolve Buffer SA in a 56℃ water bath.4. The PCR MasterMix provided with this product is 2×, when using it, you need to add template and primer, and add RNase-Free Water to make up the volume, so that its concentration is 1× to carry out the reaction.Procedure1. Fetch:Plant material: take about 10 mg of sample in a centrifuge tube (provided); Animal material: take about 10 mg of sample in a centrifuge tube (provided);Bacteria: Take 200-800 µL of bacteria in good growth condition in a centrifuge tube (self-provided) and collect the bacteria.2. Add 200 µL of Buffer SA and vortex to mix.Note: In the case of plant leaves and animal tissues, they should be ground with a pestle and mortar as much as possible: in the case of plant seeds, they should be crushed and finely ground beforehand; bacterial and 1-3 mm rat-tail samples can be directly vortex lysed.3. Add 10µL of Proteinase K, mix well, incubate at 56℃ for 10 minutes, and treat at 95℃ for 5 minutes.Note: 1) In the case of animal tissue samples, the incubation time at 56°C may be extended to 30 minutes as appropriate; if there is any incompletely digested tissue, it should be removed as thoroughly as possible after centrifugation in the next step.2) Be careful not to exceed 5 minutes when treating at 95°C.4. 13,000 rpm (~17,900 x g), centrifugation for 5 minutes.5. Transfer the supernatant to a new centrifuge tube (self-prepared) and use it directly for PCR amplification, or store the solution at 4℃ or -20℃.6. PCR amplification:1) PCR reaction system:The following examples are conventional PCR reaction systems and reaction conditions, which should be improved and optimized according to the template, primer structure and target fragment size in actual operation.reagents20 µL systemfinal concentration2×PCR MasterMix10 µL1×Forward Primer, 10 µM1 µL0.4 µMReverse Primer, 10 µM1 µL0.4 µMTemplate DNA1-2 µL RNase-free Waterup to 20 µLNote: Please use the final concentration of 0.2-0.6µM as a reference for setting the range of primer concentration. If the amplification efficiency is not high, the concentration of primer can be increased; if a non-specific reaction occurs, the concentration of primer can be decreased, thus optimizing the reaction system.2）PCR reaction conditions:movetemptimingpremutability94°C2mindenaturation94°C30sannealing (metallurgy)55-65°C30s30-40 cyclesreach72°C60sultimate extension72°C5minNote: 1) In general, the annealing temperature is 5℃ lower than the melting temperature of the amplification primer Tm, and the annealing time is generally 30-60 seconds. When the desired amplification efficiency cannot be obtained, the annealing temperature should be lowered appropriately; when a non-specific reaction occurs, the annealing temperature should be raised, thus optimizing the reaction conditions.(2) The extension time is set according to the size of the fragment to be amplified, and the amplification efficiency of Taq DNA Polymerase included in this product is 1kb/30s. 3) The number of cycles can be set according to the downstream application of the amplification product. If the number of cycles is too low, the amplification is insufficient; if the number of cycles is high, the chance of mismatch will increase and the non-specific background will be serious. Therefore, the number of cycles should be minimized under the premise of ensuring the product yield.(3) Result detection: 5 µL of reaction product was taken at the end of the reaction and directly detected by agarose gel electrophoresis... Read More | Inquire | The content of this cell is too long for an XLSX file (more than 32767 characters). Please use the CSV format for this export | DescriptionThe Universal Coupling Kit makes particle-based immunoassays, lateral flow tests and biomolecule separation applications more flexible than ever before. It is the only kit that allows users to select and couple their choice of carboxylated particle with their chosen protein.Employing a DescriptionThe Universal Coupling Kit makes particle-based immunoassays, lateral flow tests and biomolecule separation applications more flexible than ever before. It is the only kit that allows users to select and couple their choice of carboxylated particle with their chosen protein.Employing a unique mechanism to immobilise proteins, Anteo′s advantages outweigh those of conventional covalent chemistries such as NHS/EDC or passive binding. This facilitates coupling of antibodies with ease, improved functionality and reproducibility, leading to better uniformity between experiments.Anteo′s Activation Reagent is water-based and replaces the dry chemicals you would use with the traditional NHS/EDC method. Our One-Step-Activation only takes one hour, and improves efficiency in terms of both time and cost. It also provides the ability to either store activated particles up to 12 months for later use, or to immediately couple proteins.Particle-Based Immunoassays, Lateral Flow, Bioseparations and Immunoprecipitation... Read More |