| Description | Creatine Kinase (CK) is primarily found in tissues such as the heart, muscle, and brain. It reversibly catalyzes the transphosphorylation reaction between creatine and ATP, playing a vital role in energy transfer, muscle contraction, and ATP regeneration. It is a crucial clinical indicator for Creatine Kinase (CK) is primarily found in tissues such as the heart, muscle, and brain. It reversibly catalyzes the transphosphorylation reaction between creatine and ATP, playing a vital role in energy transfer, muscle contraction, and ATP regeneration. It is a crucial clinical indicator for diagnosing heart and brain diseases.Assay PrincipleCK catalyzes the conversion of Phosphocreatine and ADP to Creatine and ATP. Hexokinase then catalyzes the reaction of ATP with Glucose to form Glucose-6-Phosphate (G6P). Subsequently, Glucose-6-Phosphate Dehydrogenase (G6PDH) catalyzes the oxidation of G6P with NADP⁺ to generate NADPH, leading to an increase in absorbance at 340 nm. Component100TStorageExtraction Buffer100 mL2-8℃Reagent 11EA2-8℃. Store in the dark.Reagent 210 mL2-8℃Reagent 1: Powder in one bottle. Store at 4°C protected from light. Dissolve in 10 mL distilled water before use.Working Solution: Prepare immediately before use by mixing Reagent 1 and Reagent 2 at a 1:1 ratio. Incubate the Working Solution at 37°C for 2 minutes prior to use.Required Materials and Equipment (Not Provided)Balance, refrigerated centrifuge, constant temperature water bath, microplate reader, 96-well plate, and distilled water.Crude Enzyme Extraction:Tissue Samples: Homogenize the tissue on ice in Extraction Buffer at a ratio of 1:5-10 (w/v) (e.g., weigh ~0.1g tissue, add 1 mL Extraction Buffer). Centrifuge the homogenate at 10,000 g, 4°C for 15 min. Collect the supernatant for assay.Serum Samples: assay directly.Assay Procedure:Preheat the microplate reader for at least 30 minutes. Set the wavelength to 340 nm.Pipette 40 µl of sample and 60 µl of distilled water into a well of the 96-well plate. Add 100 µl of the pre-warmed (37°C) Working Solution. Mix immediately and record the initial absorbance (A₁) and the absorbance after exactly 1 minute (A₂) at 37°C. Calculate ΔA = A₂ - A₁.CK Enzyme Activity Calculation:General Parameters:ε (NADPH molar extinction coefficient) = 6220 L/mol/cmd (Light path for 96-well plate) = 0.5 cmVₜₒₜₐₗ (Total reaction volume) = 0.2 mL (200 µL)Vₛₐₘₚₗₑ (Sample volume in reaction) = 0.04 mL (40 µL)T (Reaction time) = 1 minCpr (Sample protein concentration, mg/mL)W (Sample mass, g)Vₛₐₘₚₗₑₜₒₜₐₗ (Total extract volume) = Assumed 1 mL for tissue calculations1. Based on Tissue Protein Content:Definition: One unit of activity is defined as the amount of enzyme that generates 1 nmol of NADPH per minute per mg of protein at 37°C, pH 7.0.Calculation:CK Activity (nmol/min/mg prot) = [ΔA / (ε × d)] × Vₜₒₜₐₗ ÷ (Vₛₐₘₚₗₑ × Cpr) ÷ TSimplified Formula: CK (nmol/min/mg prot) = 1608 × ΔA ÷ Cpr2. Based on Tissue Sample Mass:Definition: One unit of activity is defined as the amount of enzyme that generates 1 nmol of NADPH per minute per gram of fresh tissue at 37°C, pH 7.0.Calculation:CK Activity (nmol/min/g fresh weight) = [ΔA / (ε × d)] × Vₜₒₜₐₗ ÷ (Vₛₐₘₚₗₑ / Vₛₐₘₚₗₑₜₒₜₐₗ × W) ÷ TSimplified Formula: CK (nmol/min/g fresh weight) = 1608 × ΔA ÷ W3. Based on Serum:Definition: One unit of activity is defined as the amount of enzyme that generates 1 nmol of NADPH per minute per liter of serum at 37°C, pH 7.0.Calculation:CK Activity (nmol/min/L) = [ΔA / (ε × d)] × Vₜₒₜₐₗ ÷ Vₛₐₘₚₗₑ ÷ TSimplified Formula: CK (nmol/min/L) = 1608 × ΔANotesBefore formal assay, it is essential to perform a pilot test with 2-3 samples expected to have significant differences in activity.The prepared Working Solution is stable at 4°C for 7 days. However, it is recommended to use it as soon as possible after preparation.CK in serum is unstable. Determine the activity as soon as possible after sample collection. It can be stored protected from light at 4°C for up to 24 hours.Sample protein content needs to be determined separately. A BCA Protein Assay Kit can be used for this purpose.If the OD value is greater than 0.5, dilute the sample appropriately with Extraction Buffer and account for the dilution factor (D) in the calculation formulas (e.g., 1608 × ΔA × D ÷ Cpr)... Read More | DescriptionCholesteryl ester transfer protein (CETP) is present in normal human plasma and transfers neutral lipids from high density lipoproteins (HDL) to very low density lipoprotein (VLDL) and low density lipoprotein (LDL). CETP plays an important role in lipoprotein metabolism and influences theDescriptionCholesteryl ester transfer protein (CETP) is present in normal human plasma and transfers neutral lipids from high density lipoproteins (HDL) to very low density lipoprotein (VLDL) and low density lipoprotein (LDL). CETP plays an important role in lipoprotein metabolism and influences the reverse cholesterol transport pathway.Preparation instructionsSuitable for high-throughput screening (HTS), mechanism of action (MOA) studies, and structure-activity relationship (SAR) work in CETP sources.PrincipleThe CETP RP Activity Assay uses a proprietary substrate that enables the detection of CETP-mediated neutral lipid mass transfer. The method is useful for measuring CETP activity in recombinant protein (RP) or purified CETP samples and has a high D... Read More | RAFT Agent Kit for controlling polymerizations at the molecular level detailed list of products: Catalog Number Product Name Component Catalog Number Component Name Component CAS Specification&Purity R396714 RAFT Agent Kit for controlling polymerizations at the molecular level C139356-500mg 4-RAFT Agent Kit for controlling polymerizations at the molecular level detailed list of products: Catalog Number Product Name Component Catalog Number Component Name Component CAS Specification&Purity R396714 RAFT Agent Kit for controlling polymerizations at the molecular level C139356-500mg 4-Cyano-4-(dodecylsulfanylthiocarbonyl)sulfanylpentanoic acid 870196-80-8 See Component Catalog Number R396714 RAFT Agent Kit for controlling polymerizations at the molecular level C396701-500mg Cyanomethyl dodecyl trithiocarbonate 796045-97-1 See Component Catalog Number R396714 RAFT Agent Kit for controlling polymerizations at the molecular level C396703-500mg Cyanomethyl methyl(phenyl)carbamodithioate 76926-16-4 See Component Catalog Number R396714 RAFT Agent Kit for controlling polymerizations at the molecular level C168358-500mg 2-Cyano-2-propyl benzodithioate 201611-85-0 See Component Catalog Number R396714 RAFT Agent Kit for controlling polymerizations at the molecular level C396706-500mg 2-(2-Cyanoprop-2-yl)-S-dodecyltrithiocarbonate 870196-83-1 See Component Catalog Number R396714 RAFT Agent Kit for controlling polymerizations at the molecular level C132316-500mg 4-Cyano-4-(phenylcarbonothioylthio)pentanoic Acid 201611-92-9 See Component Catalog Number R396714 RAFT Agent Kit for controlling polymerizations at the molecular level S396708-500mg S,S-Dibenzyl trithiocarbonate 26504-29-0 See Component Catalog Number R396714 RAFT Agent Kit for controlling polymerizations at the molecular level D396711-500mg 2-(Dodecylthiocarbonothioylthio)-2-methylpropionic acid 461642-78-4 See Component Catalog Number... Read More | This kit combines efficient guanidine isothiocyanate lysis technology with silicon matrix membrane purification technology to efficiently extract total RNA from animal cells and tissues. The starting sample usually has a maximum of 30 mg of tissue or 1 x 107 cells. This reagent kit can also recover This kit combines efficient guanidine isothiocyanate lysis technology with silicon matrix membrane purification technology to efficiently extract total RNA from animal cells and tissues. The starting sample usually has a maximum of 30 mg of tissue or 1 x 107 cells. This reagent kit can also recover partially purified RNA, RNA obtained from in vitro transcription and enzymatic reactions. This reagent kit can extract and purify high-quality RNA with a molecular weight greater than 200 bases, with almost no DNA residue. If RNA experiments are to be conducted that are highly sensitive to trace amounts of DNA, residual DNA can be digested and removed on a column using DNase I without RNase. The extracted RNA can be used for downstream experiments such as RT-PCR, Northern Blot, Dot Blot, etc. R666020Component50 TStorageR666020ABuffer RL35 mLRTR666020BBuffer RW140 mLRTR666020CBuffer RW2 (concentrate)11 mLRTR666020DRNase-Free Water10 mLRTR666020ESpin Columns RM with Collection Tubes50 setsRTR666020FRNase-Free Centrifuge Tubes (1.5 mL)50 EART Self prepared reagents: β- Mercaptoethanol, anhydrous ethanol (newly opened or dedicated for RNA extraction).Preparation and important precautions before the experimentTo prevent RNase pollution, attention should be paid to the following aspects:1) Use RNase free plastic products and gun heads to avoid cross contamination.2) Glassware should be dry baked at a high temperature of 180 ℃ for 4 hours before use, while plastic containers can be soaked in 0.5 M NaOH for 10 minutes, thoroughly rinsed with water, and then sterilized under high pressure.3) Prepare the solution using water without RNase.4) Operators should wear disposable masks and gloves, and change gloves frequently during the experiment.2. The extracted samples should avoid repeated freeze-thaw cycles, otherwise it will affect the quantity and quality of RNA extraction.3. Before use, please check if there is any crystallization or precipitation in the Buffer RL. It can be heated at 56 ℃ and re solved. Please add Buffer RL before use β- Mercaptoethanol, with a final concentration of 1%. Add 10 to 1ml Buffer RL µ L β- Mercaptoethanol. join β- The buffer RL room temperature of mercaptoethanol can be stored for one month.4. Before the first use, anhydrous ethanol should be added to Buffer RW2 according to the instructions on the reagent bottle label.5. All centrifugation steps should be carried out at room temperature unless otherwise specified, and all operation steps should be carried out quickly.6. If downstream experiments are highly sensitive to DNA, it is recommended to treat RNA with DNase I that does not contain RNase.Operation steps1. Sample processing1a organization: Grind the organization in liquid nitrogen. Add 600 to every 20-30 mg of tissue µ L Buffer RL (check if it is added before use) β- Mercaptoethanol), tissue sample less than 20 mg plus 350 µ Buffer RL. The sample volume shall not exceed one tenth of the buffer RL volume.1b Single layer culture of cells: The cells are directly lysed or processed into cell suspensions in a culture bottle, centrifuged to obtain cell precipitates, and the supernatant is discarded. 600 is added every 6-10 cm2 of culture area µ Buffer RL, less than 6 cm2, add 350 µ Blow buffer RL several times to fully crack it.1c cell suspension: Centrifuge at 12000 rpm (~13400 × g) for 1 minute to discard the supernatant and obtain cell precipitate. Add 600 cells every 5 × 106-1 × 107 cells µ Buffer RL, less than 5 × 106 cells added to 350 µ Blow buffer RL several times to fully crack it.Attention:1) Try to eliminate the cell culture medium as much as possible, as it may inhibit cell lysis and affect RNA production.2) Try to fully suspend and lyse the cells, otherwise it will affect RNA production.2. After the sample is fully lysed, it should be left at room temperature for 5 minutes to completely separate the protein nucleic acid complex.3. Centrifuge at 2000rpm for 2-5 minutes, take the supernatant and proceed to the next step.4. Add 1 volume (600) µ L or 350 µ l) Mix 70% ethanol (prepared without RNase water) well.Attention: Adding ethanol may cause precipitation and will not affect subsequent experiments.5. Add all the solution obtained in step 4 to the Spin Columns RM that has been loaded into the collection tube. If it is not possible to add all the solution to the adsorption column at once, please transfer it in two batches, centrifuge at 12000 rpm for 1 minute, discard the waste liquid in the collection tube, and place the adsorption column in the collection tube. Attention: The maximum loading capacity of the adsorption column is 100 µ g, do not overload, otherwise it will affect the yield and purity of RNA.6. Add 700 to the adsorption column µ Centrifuge at 12000 rpm for 1 minute, discard the waste liquid from the collection tube, and place the adsorption column in the collection tube.Optional steps: If conducting RNA experiments that are highly sensitive to trace amounts of DNA, replace step 6 with the following steps.1) Add 350 to the adsorption column µ L Buffer RW1, centrifuge at 12000 rpm for 15 seconds, discard the waste liquid, and place the adsorption column back into the recovery manifold.2) Preparation of DNase I mixture: Take 52 µ Add 8 RNase Free Water to it µ 10 x Reaction Buffer and 20 µ DNase I (1 U/ µ l) Mix well and prepare to a final volume of 80 µ The reaction solution of L.Attention: The above system is configured according to our company's DNase I reaction system. Please refer to the corresponding manual for other company products.3) Add 80 µ l of the prepared DNase I reaction solution directly to the adsorption column and incubate at 20-30 ℃ for 15 minutes.4) Add 350 to the adsorption column µ L Buffer RW1, centrifuge at 12000 rpm for 15 seconds, discard the waste liquid, and place the adsorption column back into the recovery manifold.7. Add 500 to the adsorption column µ Buffer RW2 (check if anhydrous ethanol is added before use), centrifuge at 12000 rpm for 1 minute, discard the waste liquid in the collection tube, and place the adsorption column in the collection tube.8. Repeat step 7. 9. Centrifuge at 12000 rpm for 2 minutes and discard the waste liquid from the collection tube. Place the adsorption column at room temperature for a few minutes to thoroughly air dry.Note: The purpose of this step is to remove residual ethanol from the adsorption column, which can affect subsequent enzymatic reactions (such as enzyme digestion, PCR, etc.).10. Place the adsorption column in a new RNase free centrifuge tube, and add 30-50 to the middle of the adsorption column in the air µ Place RNase Free Water at room temperature for 1 minute, centrifuge at 12000 rpm for 1 minute, collect RNA solution, and store RNA at -70 ℃ to prevent degradation.Attention:1) The volume of RNase Free Water should not be less than 30 µ l. Small volume affects the recovery rate.2) If you want to increase RNA production, you can use 30-50 µ Repeat step 10 for the new RNase Free Water.3) If you want to increase the RNA concentration, you can add the obtained solution back to the adsorption column and repeat step 10... Read More | DescriptionThe Universal Coupling Kit makes particle-based immunoassays, lateral flow tests and biomolecule separation applications more flexible than ever before. It is the only kit that allows users to select and couple their choice of carboxylated particle with their chosen protein.Employing a DescriptionThe Universal Coupling Kit makes particle-based immunoassays, lateral flow tests and biomolecule separation applications more flexible than ever before. It is the only kit that allows users to select and couple their choice of carboxylated particle with their chosen protein.Employing a unique mechanism to immobilise proteins, Anteo′s advantages outweigh those of conventional covalent chemistries such as NHS/EDC or passive binding. This facilitates coupling of antibodies with ease, improved functionality and reproducibility, leading to better uniformity between experiments.Anteo′s Activation Reagent is water-based and replaces the dry chemicals you would use with the traditional NHS/EDC method. Our One-Step-Activation only takes one hour, and improves efficiency in terms of both time and cost. It also provides the ability to either store activated particles up to 12 months for later use, or to immediately couple proteins.Particle-Based Immunoassays, Lateral Flow, Bioseparations and Immunoprecipitation... Read More |