| Description | The CO2 content in the air is an important measure for checking the ventilation behavior in offices, classrooms, lecture halls, etc. The CO2 / carbon dioxide measuring device helps to ensure that, for example, there is regular ventilation for employees in the office. The CO2 / carbon dioxide The CO2 content in the air is an important measure for checking the ventilation behavior in offices, classrooms, lecture halls, etc. The CO2 / carbon dioxide measuring device helps to ensure that, for example, there is regular ventilation for employees in the office. The CO2 / carbon dioxide measuring device checks indoor air quality via the CO2 content. If the CO2 concentration is below 1000 ppm, the indoor air quality is optimal. Good indoor air quality helps to promote concentration. It is also ensured that the aerosol concentration in the air is low, as the aerosols are repeatedly mixed with fresh air. The CO2 / carbon dioxide measuring device shows the air quality as a numerical measured value and as a traffic light indicator. At the push of a button, the CO2 content of the last five hours can be shown on the display. In addition to the CO2 measuring function, the CO2 / carbon dioxide measuring device is equipped with a sensor for temperature and humidity.... Read More | Air Quality Meter / Measures temperature and humidity / Visual and audible alarm / USB-C interface / Battery status indicator / Modern design and compact size
A Air Quality Meter is an important device for monitoring indoor air quality. It can be used in a variety of ways - whether in homes, officesAir Quality Meter / Measures temperature and humidity / Visual and audible alarm / USB-C interface / Battery status indicator / Modern design and compact size
A Air Quality Meter is an important device for monitoring indoor air quality. It can be used in a variety of ways - whether in homes, offices, workshops, schools or public facilities. The detector reliably measures the CO content in the air and makes it possible to recognize critical concentrations at an early stage and act accordingly.
The Air Quality Meter detects CO values in the range from 0 ... 500 ppm with a fine resolution of 1 ppm. It also measures the relative humidity in the range from 20 ... 85% (also with 1% resolution) and the temperature from -10 ... 50°C / 14 ... 122°F. If required, the temperature display can also be switched to Fahrenheit. All measured values are shown on a 2 inch LCD display.
In the event of increased CO values, the detector emits both visual and acoustic warning signals. An integrated traffic light function clearly displays the air quality: Green stands for 0 ... 100 ppm, orange for 101 ... 200 ppm and red for 201 ... 500 ppm. If the value exceeds 100 ppm, an additional acoustic warning signal sounds to indicate a potential health hazard.
Equipped with an integrated rechargeable lithium battery that can be conveniently charged via USB-C, the detector is particularly flexible to use. An integrated rubber strap makes it easy to transport and allows the device to be carried or hung up conveniently. With its compact dimensions of 70 x 70 x 28 mm / 2.8 x 2.8 x 1.1 in, modern design and easy handling, it is a practical helper in everyday life.
The Air Quality Meter is suitable for both private and professional use - for example in schools, care facilities, offices or industrial environments - wherever safe indoor air quality is crucial.... Read More | The Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, asThe Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, as well as coaxial cables, such as those used in TV, antenna, and surveillance systems.
Testing is carried out using a two-part system consisting of a main unit and a remote unit, which also allows permanently installed cables to be tested reliably. The most important test procedures include continuity testing of the conductors (pins 1–8), wiring testing to check the correct assignment of the wire pairs, and the detection of short circuits, wiring faults, and split-pair faults. In addition, the shielding of shielded cables is checked. The test range covers cable lengths of up to 305 m, whilst the minimum cable length for split-pair detection is approximately 0.5 m.
Our Cable Detector operates using test signals transmitted between the main unit and the remote unit. The results are displayed via LED indicators. Steady LEDs indicate correct wiring, whilst flashing LEDs indicate faults in the respective wire pairs. Additional status LEDs indicate the type of fault, such as short circuit, miswiring, reversal, or split pair.
The Cable Detector is used in network technology, building cabling, and in IT and communications installations, and is designed for electricians, network technicians, and service technicians to quickly test cable runs.... Read More | The portable Health & Safety - Surface Resistance Meter on the principle of a two-point pin probe and enables simple and reliable measurement of the surface resistivity of materials - without the need for a megohmmeter, electrometer or other high-voltage measuring devices.
Thanks to its slim and The portable Health & Safety - Surface Resistance Meter on the principle of a two-point pin probe and enables simple and reliable measurement of the surface resistivity of materials - without the need for a megohmmeter, electrometer or other high-voltage measuring devices.
Thanks to its slim and handy design, the device can be conveniently operated with one hand and is ideal for on-site testing or mobile use in production and laboratories. Despite its compact size, it delivers precise results for quickly assessing whether a material is insulating, dissipative or conductive.
The Health & Safety - Surface Resistance Meter uses gold-plated, spring-loaded electrodes that ensure excellent contact with a wide variety of surfaces and minimize contact resistance. All electrodes are replaceable ATE quality pogo pin probes, made from beryllium copper with a hard gold plating of at least 60 microinches - robust, durable and precise.
The two-point probe head is directly connected to an integrated surface resistance measuring device, which measures the surface resistance at a test voltage of approx. 9 volts. The measurement results are shown on a colored LED display. This allows the ESD properties of a material to be clearly recognized at a glance.
With its combination of precise technology, easy handling, compact design and clear LED display, this Health & Safety is the perfect solution for quick on-site testing, quality control and ESD compliance tests in production, laboratories and development.... Read More | This innovative 3-in-1 Oscilloscope is the perfect combination of a powerful Oscilloscope, a versatile multimeter and a signal generator. It has been specially developed for electronics technicians, engineers and hobby users who are looking for a compact, versatile and user-friendly device to carry This innovative 3-in-1 Oscilloscope is the perfect combination of a powerful Oscilloscope, a versatile multimeter and a signal generator. It has been specially developed for electronics technicians, engineers and hobby users who are looking for a compact, versatile and user-friendly device to carry out their measurement tasks efficiently.
The 2-channel Oscilloscope offers a bandwidth of 10 MHz and a sampling rate of 50 MS/s, which enables signals to be reliably recorded and analysed. Whether troubleshooting circuits, observing waveforms or analysing transients, this Oscilloscope delivers clear and precise results. Thanks to its high resolution and simple operation, even complex signal curves can be easily visualised. The Oscilloscope image can be saved to the internal memory as a screenshot and transferred to a computer via the USB-C interface.
The device also has extensive multimeter functions that cover a wide range of measurements. These include voltage measurements (DC and AC voltage), current measurements (DC and AC current), resistance measurements, capacitance measurements and diode test. Another practical feature is the integrated non-contact voltage detection, which allows you to reliably detect live wires.
The signal generator ideally complements the device by generating signals within a range of 1 Hz to 2 MHz. It supports various signal shapes such as sine, square, triangle, half wave, full wave, noise and DC signals. This function makes the Oscilloscope particularly useful for tests, simulations and the development of circuits. Thanks to its compact design and the combination of Oscilloscope, multimeter and signal generator, this device is an indispensable tool for anyone who values efficiency and precision when working with electronics.... Read More |