| Description | Gas Detector / Gas Detection Instrument / Detects natural gas & LPG / Heat and gas sensor / WLAN / Voice announcement / Control via app / Real-time alarm / Easy installation
A Gas Detector / Gas Detection Instrument is an important safety device. It recognizes dangerous gas concentrations in the Gas Detector / Gas Detection Instrument / Detects natural gas & LPG / Heat and gas sensor / WLAN / Voice announcement / Control via app / Real-time alarm / Easy installation
A Gas Detector / Gas Detection Instrument is an important safety device. It recognizes dangerous gas concentrations in the air and sounds the alarm in good time to prevent accidents such as explosions or poisoning. Our Gas Detector / Gas Detection Instrument has been specially developed for use in homes, offices and similar indoor areas. It detects both natural gas (methane) and liquefied petroleum gas (LPG, consisting of propane and butane) and reacts as soon as a certain concentration is exceeded.
Our Gas Detector / Gas Detection Instrument measures gas concentrations in the range of 0 ... 100% of the lower explosion limit (LEL), whereby the alarm is triggered at 6% LEL. The response time is a maximum of 30 seconds and the alarm is triggered at a volume of over 70 decibels. A heat sensor is also integrated, which also triggers an alarm at an ambient temperature of 57°C / 134.6°F.
The detector is equipped with a color LCD display that shows the date and time as well as the gas values, the temperature and the remaining sensor life. A Wi-Fi connection is used to connect to the "Smart Life" app, which can be used to monitor the status of the device worldwide. In the event of an alarm, an acoustic and visual warning, a voice message and a push notification are sent to the smartphone. In addition, a connected valve can be activated automatically to stop the gas supply. The sensor has a service life of five years and the device requires a warm-up time of 180 seconds after switching on. The detector is supplied with 5V/1 A power via micro USB and consumes less than 200 mA.
The installation of the Gas Detector / Gas Detection Instrument depends on the type of gas used: for natural gas, which is lighter than air, the device is installed about 30 cm below the ceiling, for LPG, which is heavier than air, about 30 cm above the floor. The distance to the gas source should be 1.5 to 4 meters / 5 to 13 ft. The Gas Detector / Gas Detection Instrument can be attached either with screws or double-sided adhesive tape. Regular tests, which can also be carried out via the app or manually on the device, ensure that it is working properly.
Overall, the Gas Detector / Gas Detection Instrument offers a modern and reliable solution for the early detection of gas leaks and thus makes a significant contribution to increasing safety in rooms supplied with gas. This model of Gas Detector / Gas Detection Instrument combines modern technology with simple operation and is ideal for private and commercial applications.... Read More | Portable handheld device for monitoring particulate matter (PM) concentrations in the air / 2.5 µm and 10 µm particle sizes / Measures air temperature and relative humidity. Designed to aid in indoor air quality (IAQ) assessments, this dust monitor also measures air temperature and relative humidityPortable handheld device for monitoring particulate matter (PM) concentrations in the air / 2.5 µm and 10 µm particle sizes / Measures air temperature and relative humidity. Designed to aid in indoor air quality (IAQ) assessments, this dust monitor also measures air temperature and relative humidity (RH). The dust monitor can be powered either by the built-in rechargeable battery or the USB port. The USB port also is used to charge the battery. At full charge, the battery provides up to 5 hours of continuous operation or unlimited operation when plugged into a USB power source. The dust monitor displays all measurements simultaneously on the device's 2.4" full-color LCD screen. PM values ??appear the largest in the colors green, yellow, gold, orange, pink and red. This visual color-coding system makes it easy to recognize when PM concentration levels become dangerous, allowing for quick action.... Read More | Gas Detector / Gas Detection Instrument / Real-time measurement of HCHO, TVOC, temperature & humidity / Audible alarm / 2.8 inch colour display / Memory
The Gas Detector / Gas Detection Instrument is a versatile device for monitoring the air quality in indoor spaces such as homes, offices, Gas Detector / Gas Detection Instrument / Real-time measurement of HCHO, TVOC, temperature & humidity / Audible alarm / 2.8 inch colour display / Memory
The Gas Detector / Gas Detection Instrument is a versatile device for monitoring the air quality in indoor spaces such as homes, offices, workshops, schools or public facilities. It is used for the simultaneous measurement of formaldehyde (HCHO), volatile organic compounds (TVOC), ambient temperature and relative humidity. The Gas Detector / Gas Detection Instrument has a 2.8-inch color display that shows all measured values in real time and also visually assesses the air quality in three stages - green for "good", yellow for "poor" and red for "very poor". The Gas Detector / Gas Detection Instrument also has an acoustic alarm function with adjustable threshold values and sound types, which is triggered when defined measured values are exceeded.
For data storage, the device offers space for up to 200 measuring points on 5 pages, which corresponds to a total capacity of 1000 measurements per measured variable. The values for formaldehyde, TVOC and temperature are stored. The storage intervals and the number of collection points can be set individually, whereby the stored data can only be retrieved at any time via a playback function in the device. Other functions include a real-time clock, battery status display, adjustable measuring rate, automatic switch-off time, adjustable screen brightness and the option of active fan control. The temperature unit can be switched between Celsius and Fahrenheit.
The Gas Detector / Gas Detection Instrument is powered by an integrated 3.7V Li-Po battery and charged via a USB type C cable. The charge status is shown on the display during operation and charging. As a compact, precise and easy-to-use Gas Detector / Gas Detection Instrument, the Gas Detector / Gas Detection Instrument is ideal for continuously monitoring indoor air quality and helps to detect potential exposure to pollutants such as formaldehyde or organic vapors at an early stage and take appropriate countermeasures.... Read More | Illuminometer with external probe / Sampling rate 4 Hz / Measuring range 0 ... 400 kLux / Micro-USB interface / Units: lux, footcandle. The illuminometer has additional functions so that an analysis of the illuminance can be carried out. With the additional functions of the illuminometer the largestIlluminometer with external probe / Sampling rate 4 Hz / Measuring range 0 ... 400 kLux / Micro-USB interface / Units: lux, footcandle. The illuminometer has additional functions so that an analysis of the illuminance can be carried out. With the additional functions of the illuminometer the largest and smallest measured value can be output using the "MIN" and "MAX" buttons. In addition, the displayed measured value can be set in relation to a reference using the "REL" button. With the "PEAK" function, the illuminometer records peak values. The illuminometer has a sampling rate of 10 µs. The PCE-LMD 10 also has a data memory of 32,000 measured values. The measured values ??from the illuminometer can be read out and analyzed on the PC after a measurement. A live measurement on the PC with the illuminometer is also possible. The data from the illuminometer can be exported in CSV format for further processing.... Read More | Magnetometer / Magnetic Field Detector / Combined display / Memory for 10000 values / Wireless and USB-C interface / Incl. calibration standard
The Magnetometer / Magnetic Field Detector can be used to determine the relative magnetic permeability µr of materials and construction parts in the range Magnetometer / Magnetic Field Detector / Combined display / Memory for 10000 values / Wireless and USB-C interface / Incl. calibration standard
The Magnetometer / Magnetic Field Detector can be used to determine the relative magnetic permeability µr of materials and construction parts in the range between 1,000 and 5,000. Magnetic permeability, also known as magnetic conductivity, indicates how strongly a material can be magnetized. This Magnetometer / Magnetic Field Detector is ideal for material testing - especially for ferromagnetic material testing - in order to provide precise data for material testing NDT (non-destructive testing).
Areas of application include quality control of stainless steels, non-destructive material testing of construction parts, material selection for electron and ion physics equipment as well as for nuclear resonance devices, or the detection of material changes in highly stressed parts. The Magnetometer / Magnetic Field Detector has a graphic LCD touch panel with innovative user guidance and a resolution of 320 × 480 pixels.
The Magnetometer / Magnetic Field Detector supports all areas of permeability measurement with a flexible measured value memory, a combined digital and analogue display and peak value measurement. You can transfer the data to a Windows PC as well as to an Android or iOS app via the wireless interface. The Magnetometer / Magnetic Field Detector can be connected to an external power source in continuous operation via the USB interface.
You can check the accuracy of the measurement at any time using the calibration standard supplied with the permeability measuring device. The standard calibration standard has a value of µr ˜ 1.35. Calibration standards with reference values of µr ˜ 1.03 and µr ˜ 1.11 are also available.... Read More |