| Description | Gas Detector / Gas Detection Instrument / Detects natural gas & LPG / Heat and gas sensor / WLAN / Voice announcement / Control via app / Real-time alarm / Easy installation
A Gas Detector / Gas Detection Instrument is an important safety device. It recognizes dangerous gas concentrations in the Gas Detector / Gas Detection Instrument / Detects natural gas & LPG / Heat and gas sensor / WLAN / Voice announcement / Control via app / Real-time alarm / Easy installation
A Gas Detector / Gas Detection Instrument is an important safety device. It recognizes dangerous gas concentrations in the air and sounds the alarm in good time to prevent accidents such as explosions or poisoning. Our Gas Detector / Gas Detection Instrument has been specially developed for use in homes, offices and similar indoor areas. It detects both natural gas (methane) and liquefied petroleum gas (LPG, consisting of propane and butane) and reacts as soon as a certain concentration is exceeded.
Our Gas Detector / Gas Detection Instrument measures gas concentrations in the range of 0 ... 100% of the lower explosion limit (LEL), whereby the alarm is triggered at 6% LEL. The response time is a maximum of 30 seconds and the alarm is triggered at a volume of over 70 decibels. A heat sensor is also integrated, which also triggers an alarm at an ambient temperature of 57°C / 134.6°F.
The detector is equipped with a color LCD display that shows the date and time as well as the gas values, the temperature and the remaining sensor life. A Wi-Fi connection is used to connect to the "Smart Life" app, which can be used to monitor the status of the device worldwide. In the event of an alarm, an acoustic and visual warning, a voice message and a push notification are sent to the smartphone. In addition, a connected valve can be activated automatically to stop the gas supply. The sensor has a service life of five years and the device requires a warm-up time of 180 seconds after switching on. The detector is supplied with 5V/1 A power via micro USB and consumes less than 200 mA.
The installation of the Gas Detector / Gas Detection Instrument depends on the type of gas used: for natural gas, which is lighter than air, the device is installed about 30 cm below the ceiling, for LPG, which is heavier than air, about 30 cm above the floor. The distance to the gas source should be 1.5 to 4 meters / 5 to 13 ft. The Gas Detector / Gas Detection Instrument can be attached either with screws or double-sided adhesive tape. Regular tests, which can also be carried out via the app or manually on the device, ensure that it is working properly.
Overall, the Gas Detector / Gas Detection Instrument offers a modern and reliable solution for the early detection of gas leaks and thus makes a significant contribution to increasing safety in rooms supplied with gas. This model of Gas Detector / Gas Detection Instrument combines modern technology with simple operation and is ideal for private and commercial applications.... Read More | Portable handheld device for monitoring particulate matter (PM) concentrations in the air / 2.5 µm and 10 µm particle sizes / Measures air temperature and relative humidity. Designed to aid in indoor air quality (IAQ) assessments, this dust monitor also measures air temperature and relative humidityPortable handheld device for monitoring particulate matter (PM) concentrations in the air / 2.5 µm and 10 µm particle sizes / Measures air temperature and relative humidity. Designed to aid in indoor air quality (IAQ) assessments, this dust monitor also measures air temperature and relative humidity (RH). The dust monitor can be powered either by the built-in rechargeable battery or the USB port. The USB port also is used to charge the battery. At full charge, the battery provides up to 5 hours of continuous operation or unlimited operation when plugged into a USB power source. The dust monitor displays all measurements simultaneously on the device's 2.4" full-color LCD screen. PM values ??appear the largest in the colors green, yellow, gold, orange, pink and red. This visual color-coding system makes it easy to recognize when PM concentration levels become dangerous, allowing for quick action.... Read More | The Clamp Meter is a multifunctional meter for the precise measurement of alternating and direct voltage as well as alternating and direct current that can be measured without direct contact to the line. The Clamp Meter is suitable for measuring resistance, temperature, diodes, continuity, The Clamp Meter is a multifunctional meter for the precise measurement of alternating and direct voltage as well as alternating and direct current that can be measured without direct contact to the line. The Clamp Meter is suitable for measuring resistance, temperature, diodes, continuity, frequencies and capacitance and is particularly useful for diagnosing electrical and electronic components.
For maximum measurement accuracy, the Clamp Meter supports True RMS for non-sinusoidal waveforms and a Low Impedance (LoZ) function to reduce interference. The non-contact voltage test enables reliable detection of voltages in cables and sockets.
The 2-inch LC display ensures clear readability, even under poor lighting conditions and an integrated LED torch makes it easier to work in dark environments. The device also offers automatic and manual measurement range selection, allowing it to be flexibly adapted to different measuring situations. The device also has a practical zero key which enables accurate measurement of low currents, especially when measuring direct current (DC) and ensures the compensation of deviations of the output value. Other functions include overload protection, data hold, min, max and an automatic power-off after 15 minutes to conserve battery life. The power-off can also be deactivated for longer measurements.
Compact and easy to use, the Clamp Meter is ideal for electrical installations, maintenance work and use in automation technology. It enables safe and efficient measurements, often without direct intervention in the circuit.... Read More | This HVAC Meter / HVACR Tester is a portable HVAC Meter / HVACR Tester that has been specially developed for the precise measurement of flow velocity in open channels, such as those found in rivers, streams or canals. The measurement is based on the proven velocity-area method.
The device has a This HVAC Meter / HVACR Tester is a portable HVAC Meter / HVACR Tester that has been specially developed for the precise measurement of flow velocity in open channels, such as those found in rivers, streams or canals. The measurement is based on the proven velocity-area method.
The device has a simple, light and handy structure and is characterized by low power consumption and comprehensive functions. Thanks to the integrated Hall velocity rotation sensor, this HVAC Meter / HVACR Tester can also be used reliably in wastewater environments.
The operation is characterized by a high degree of automation, which ensures stable and reliable operation. The measurement results are shown on an LCD display with LED backlighting. The measurement itself is carried out using the rod position measurement method.
This versatile HVAC Meter / HVACR Tester is the ideal instrument for a wide range of applications, including hydrological stations, environmental monitoring, irrigation and drainage of farmland and hydrogeological surveying. The HVAC Meter / HVACR Tester is your reliable tool for on-site flow velocity measurement.... Read More | The Material Tester is a compact, portable precision tool for applications where exact torque values are crucial. It has an easy-to-read backlit display that provides clear values even in poor lighting conditions.
To assist the user, the Material Tester emits both an acoustic signal and an LED The Material Tester is a compact, portable precision tool for applications where exact torque values are crucial. It has an easy-to-read backlit display that provides clear values even in poor lighting conditions.
To assist the user, the Material Tester emits both an acoustic signal and an LED display as soon as the preset torque value is reached. Four different units of measurement (Nm, kgf-cm, lbf-ft, lbf-in) and three measuring modes - real time, peak value and preset - make it flexible to use. Automatic switch-off after a few minutes saves the batteries, and up to 999 measured values can be stored in the internal memory. The stored values can only be called up on the device.
The Material Tester is equipped with a fine-toothed ratchet head, which enables precise work even with a small radius of movement. Thanks to its robust construction made of metal and resistant plastic, it is durable and suitable for regular use. Our Material Testers are primarily used in vehicle construction, mechanical engineering, bicycle assembly and in the electrical and electronics industry. They are used to tighten bolts and nuts to a precisely defined torque in order to connect components securely and function properly without damaging them. The Material Tester is supplied in a plastic case with 2 AAA batteries.
... Read More |