| Description | Gas Detector / Gas Detection Instrument / Detects natural gas & LPG / Heat and gas sensor / WLAN / Voice announcement / Control via app / Real-time alarm / Easy installation
A Gas Detector / Gas Detection Instrument is an important safety device. It recognizes dangerous gas concentrations in the Gas Detector / Gas Detection Instrument / Detects natural gas & LPG / Heat and gas sensor / WLAN / Voice announcement / Control via app / Real-time alarm / Easy installation
A Gas Detector / Gas Detection Instrument is an important safety device. It recognizes dangerous gas concentrations in the air and sounds the alarm in good time to prevent accidents such as explosions or poisoning. Our Gas Detector / Gas Detection Instrument has been specially developed for use in homes, offices and similar indoor areas. It detects both natural gas (methane) and liquefied petroleum gas (LPG, consisting of propane and butane) and reacts as soon as a certain concentration is exceeded.
Our Gas Detector / Gas Detection Instrument measures gas concentrations in the range of 0 ... 100% of the lower explosion limit (LEL), whereby the alarm is triggered at 6% LEL. The response time is a maximum of 30 seconds and the alarm is triggered at a volume of over 70 decibels. A heat sensor is also integrated, which also triggers an alarm at an ambient temperature of 57°C / 134.6°F.
The detector is equipped with a color LCD display that shows the date and time as well as the gas values, the temperature and the remaining sensor life. A Wi-Fi connection is used to connect to the "Smart Life" app, which can be used to monitor the status of the device worldwide. In the event of an alarm, an acoustic and visual warning, a voice message and a push notification are sent to the smartphone. In addition, a connected valve can be activated automatically to stop the gas supply. The sensor has a service life of five years and the device requires a warm-up time of 180 seconds after switching on. The detector is supplied with 5V/1 A power via micro USB and consumes less than 200 mA.
The installation of the Gas Detector / Gas Detection Instrument depends on the type of gas used: for natural gas, which is lighter than air, the device is installed about 30 cm below the ceiling, for LPG, which is heavier than air, about 30 cm above the floor. The distance to the gas source should be 1.5 to 4 meters / 5 to 13 ft. The Gas Detector / Gas Detection Instrument can be attached either with screws or double-sided adhesive tape. Regular tests, which can also be carried out via the app or manually on the device, ensure that it is working properly.
Overall, the Gas Detector / Gas Detection Instrument offers a modern and reliable solution for the early detection of gas leaks and thus makes a significant contribution to increasing safety in rooms supplied with gas. This model of Gas Detector / Gas Detection Instrument combines modern technology with simple operation and is ideal for private and commercial applications.... Read More | The PCE-ATP 1-KIT with 100 swabs included is used to quickly and easily check the cleanliness of surfaces. The Hygiene Tester displays a measurement result on the large LC display after only 10 seconds. The Hygiene Tester's internal memory stores up to 10,000 measured data sets with time and date. The PCE-ATP 1-KIT with 100 swabs included is used to quickly and easily check the cleanliness of surfaces. The Hygiene Tester displays a measurement result on the large LC display after only 10 seconds. The Hygiene Tester's internal memory stores up to 10,000 measured data sets with time and date. The PCE-ATP 1 with the associated PCE-ATP SwapPens, allows a quick detection of food or microbiological residues on all surfaces in contact with the product as an effectiveness test of cleaning and disinfection measures. Quantitative determination of intracellular and extracellular adenosine triphosphate (ATP) is performed in the portable PCE-ATP 1. The measured data from the Hygiene Tester can be stored and further processed after the measurement. The Hygiene Tester is used in the hygiene control in pharmacy, medicine, gastronomy, wholesalers and more.... Read More | The CO2 content in the air is an important measure for checking the ventilation behavior in offices, classrooms, lecture halls, etc. The CO2 / carbon dioxide measuring device helps to ensure that, for example, there is regular ventilation for employees in the office. The CO2 / carbon dioxide The CO2 content in the air is an important measure for checking the ventilation behavior in offices, classrooms, lecture halls, etc. The CO2 / carbon dioxide measuring device helps to ensure that, for example, there is regular ventilation for employees in the office. The CO2 / carbon dioxide measuring device checks indoor air quality via the CO2 content. If the CO2 concentration is below 1000 ppm, the indoor air quality is optimal. Good indoor air quality helps to promote concentration. It is also ensured that the aerosol concentration in the air is low, as the aerosols are repeatedly mixed with fresh air. The CO2 / carbon dioxide measuring device shows the air quality as a numerical measured value and as a traffic light indicator. At the push of a button, the CO2 content of the last five hours can be shown on the display. In addition to the CO2 measuring function, the CO2 / carbon dioxide measuring device is equipped with a sensor for temperature and humidity.... Read More | Laboratory Technology for liquids up to 5 l / Stirring speed up to 1600 rpm / Adjustable direction of rotation / Programme mode: up to 6 stirring programmes / 1 stirring position
The Laboratory Technology is an easy-to-use laboratory device that is used for the efficient mixing of liquids. With a 3Laboratory Technology for liquids up to 5 l / Stirring speed up to 1600 rpm / Adjustable direction of rotation / Programme mode: up to 6 stirring programmes / 1 stirring position
The Laboratory Technology is an easy-to-use laboratory device that is used for the efficient mixing of liquids. With a 3.7 inch LCD display and user-friendly controls, the stirring speed, stirring time and direction of rotation can be customized. The stirring speed can be set within a range of 100 ... 1,600 rpm and has an accuracy of ± 10 rpm.
Our Laboratory Technology automatically saves the last set working parameters and up to six individually programmed stirring cycles. This enables a quick restart with the desired settings. The stirrer also has an integrated timer that allows precise time control from one second to 99 hours and 59 minutes.
The use of a brushless motor ensures maintenance-free and quiet operation. The robust acrylic stirring plate measuring 173 × 180 mm provides a stable base for a wide range of stirring tasks, even for longer operating times. The Laboratory Technology can process liquid volumes up to a maximum of 5 litres and is operated via a power supply of AC 100 ... 240V at 50 Hz.
It is a good solution for laboratory work where reliable and reproducible mixing without heating is required. It impresses with its robust design and easy handling in research facilities and industrial laboratories.... Read More | Radiation Detector / measurement of gamma, beta and X-rays / adjustable alarm values / numerical and graphical display / min, max and average values
Our Radiation Detector is mainly used to measure gamma, beta and X-rays and uses a Geiger-Müller counter to measure the intensity of ionising Radiation Detector / measurement of gamma, beta and X-rays / adjustable alarm values / numerical and graphical display / min, max and average values
Our Radiation Detector is mainly used to measure gamma, beta and X-rays and uses a Geiger-Müller counter to measure the intensity of ionising radiation. The measuring range extends from 0 ... 10 mSv/h. The cumulative dose, average and maximum dose are shown on the larg 2.3 inch multifunctional display, while the real-time measurements are also shown graphically.
The device has two alarm modes: the radiation alarm (0 ... 100 µSv/h) and the cumulative radiation alarm (0 ... 100 mSv). Both alarms are equipped with different settings for visual, audible and vibrating warning signals. The energy range of the device is between 48 and 1500 keV. The radiation measuring device is equipped with a micro USB interface and a rechargeable lithium battery.
The Radiation Detector also displays the current battery level so that the user is always informed. The brightness of the display can be adjusted as required so that it is easier to read even in different lighting conditions. The date and time are also shown on the display.
This Radiation Detector is ideal for applications in research, medicine, industry and environmental protection. It can be used in nuclear power stations, hospitals, laboratories, radiation monitoring and emergency scenarios. Furthermore, it is also useful for construction companies that are working with radioactive materials and in environmental monitoring to ensure that radiation exposure remains within safe limits.... Read More |