| Description | Gas Detector / Gas Detection Instrument / Detects natural gas & LPG / Heat and gas sensor / WLAN / Voice announcement / Control via app / Real-time alarm / Easy installation
A Gas Detector / Gas Detection Instrument is an important safety device. It recognizes dangerous gas concentrations in the Gas Detector / Gas Detection Instrument / Detects natural gas & LPG / Heat and gas sensor / WLAN / Voice announcement / Control via app / Real-time alarm / Easy installation
A Gas Detector / Gas Detection Instrument is an important safety device. It recognizes dangerous gas concentrations in the air and sounds the alarm in good time to prevent accidents such as explosions or poisoning. Our Gas Detector / Gas Detection Instrument has been specially developed for use in homes, offices and similar indoor areas. It detects both natural gas (methane) and liquefied petroleum gas (LPG, consisting of propane and butane) and reacts as soon as a certain concentration is exceeded.
Our Gas Detector / Gas Detection Instrument measures gas concentrations in the range of 0 ... 100% of the lower explosion limit (LEL), whereby the alarm is triggered at 6% LEL. The response time is a maximum of 30 seconds and the alarm is triggered at a volume of over 70 decibels. A heat sensor is also integrated, which also triggers an alarm at an ambient temperature of 57°C / 134.6°F.
The detector is equipped with a color LCD display that shows the date and time as well as the gas values, the temperature and the remaining sensor life. A Wi-Fi connection is used to connect to the "Smart Life" app, which can be used to monitor the status of the device worldwide. In the event of an alarm, an acoustic and visual warning, a voice message and a push notification are sent to the smartphone. In addition, a connected valve can be activated automatically to stop the gas supply. The sensor has a service life of five years and the device requires a warm-up time of 180 seconds after switching on. The detector is supplied with 5V/1 A power via micro USB and consumes less than 200 mA.
The installation of the Gas Detector / Gas Detection Instrument depends on the type of gas used: for natural gas, which is lighter than air, the device is installed about 30 cm below the ceiling, for LPG, which is heavier than air, about 30 cm above the floor. The distance to the gas source should be 1.5 to 4 meters / 5 to 13 ft. The Gas Detector / Gas Detection Instrument can be attached either with screws or double-sided adhesive tape. Regular tests, which can also be carried out via the app or manually on the device, ensure that it is working properly.
Overall, the Gas Detector / Gas Detection Instrument offers a modern and reliable solution for the early detection of gas leaks and thus makes a significant contribution to increasing safety in rooms supplied with gas. This model of Gas Detector / Gas Detection Instrument combines modern technology with simple operation and is ideal for private and commercial applications.... Read More | Air Quality Meter / Measures temperature and humidity / Visual and audible alarm / USB-C interface / Battery status indicator / Modern design and compact size
A Air Quality Meter is an important device for monitoring indoor air quality. It can be used in a variety of ways - whether in homes, officesAir Quality Meter / Measures temperature and humidity / Visual and audible alarm / USB-C interface / Battery status indicator / Modern design and compact size
A Air Quality Meter is an important device for monitoring indoor air quality. It can be used in a variety of ways - whether in homes, offices, workshops, schools or public facilities. The detector reliably measures the CO content in the air and makes it possible to recognize critical concentrations at an early stage and act accordingly.
The Air Quality Meter detects CO values in the range from 0 ... 500 ppm with a fine resolution of 1 ppm. It also measures the relative humidity in the range from 20 ... 85% (also with 1% resolution) and the temperature from -10 ... 50°C / 14 ... 122°F. If required, the temperature display can also be switched to Fahrenheit. All measured values are shown on a 2 inch LCD display.
In the event of increased CO values, the detector emits both visual and acoustic warning signals. An integrated traffic light function clearly displays the air quality: Green stands for 0 ... 100 ppm, orange for 101 ... 200 ppm and red for 201 ... 500 ppm. If the value exceeds 100 ppm, an additional acoustic warning signal sounds to indicate a potential health hazard.
Equipped with an integrated rechargeable lithium battery that can be conveniently charged via USB-C, the detector is particularly flexible to use. An integrated rubber strap makes it easy to transport and allows the device to be carried or hung up conveniently. With its compact dimensions of 70 x 70 x 28 mm / 2.8 x 2.8 x 1.1 in, modern design and easy handling, it is a practical helper in everyday life.
The Air Quality Meter is suitable for both private and professional use - for example in schools, care facilities, offices or industrial environments - wherever safe indoor air quality is crucial.... Read More | The illuminometer has a large measuring range of 0 … 400 lux. The illuminance is measured using an external silicon photodiode with a spectral filter. This means that the illuminometer can be positioned appropriately for every measuring task.
- Measuring range: 0,0 … 400,000 Lux
-
Resolution: 0.1 lux
-
The illuminometer has a large measuring range of 0 … 400 lux. The illuminance is measured using an external silicon photodiode with a spectral filter. This means that the illuminometer can be positioned appropriately for every measuring task.
- Measuring range: 0,0 … 400,000 Lux
-
Resolution: 0.1 lux
-
Lux and footcandle units
-
Micro-USB interface
-
Incl. software
-
Rechargeable battery
-
Data memory: 32,000 sets of readings
... Read More | Radiation Detector / measurement of gamma, beta and X-rays / adjustable alarm values / numerical and graphical display / min, max and average values
Our Radiation Detector is mainly used to measure gamma, beta and X-rays and uses a Geiger-Müller counter to measure the intensity of ionising Radiation Detector / measurement of gamma, beta and X-rays / adjustable alarm values / numerical and graphical display / min, max and average values
Our Radiation Detector is mainly used to measure gamma, beta and X-rays and uses a Geiger-Müller counter to measure the intensity of ionising radiation. The measuring range extends from 0 ... 10 mSv/h. The cumulative dose, average and maximum dose are shown on the larg 2.3 inch multifunctional display, while the real-time measurements are also shown graphically.
The device has two alarm modes: the radiation alarm (0 ... 100 µSv/h) and the cumulative radiation alarm (0 ... 100 mSv). Both alarms are equipped with different settings for visual, audible and vibrating warning signals. The energy range of the device is between 48 and 1500 keV. The radiation measuring device is equipped with a micro USB interface and a rechargeable lithium battery.
The Radiation Detector also displays the current battery level so that the user is always informed. The brightness of the display can be adjusted as required so that it is easier to read even in different lighting conditions. The date and time are also shown on the display.
This Radiation Detector is ideal for applications in research, medicine, industry and environmental protection. It can be used in nuclear power stations, hospitals, laboratories, radiation monitoring and emergency scenarios. Furthermore, it is also useful for construction companies that are working with radioactive materials and in environmental monitoring to ensure that radiation exposure remains within safe limits.... Read More | UV Meter / UV Tester with integrated sensor / Simultaneous measurement of UV radiation, energy and temperature / Trigger function / Storage of the highest measured value
The UV Meter / UV Tester is a high-precision measuring instrument for the simultaneous measurement of UV irradiance in the range UV Meter / UV Tester with integrated sensor / Simultaneous measurement of UV radiation, energy and temperature / Trigger function / Storage of the highest measured value
The UV Meter / UV Tester is a high-precision measuring instrument for the simultaneous measurement of UV irradiance in the range of 0 ...40000 mW/cm2, the UV energy from 0 ...999999 mJ/cm2 and the temperature in the range from -55°C ...125°C / -67 ... 257°F. With its wavelength range of 340 nm to 420 nm, it is ideal for applications in UV curing systems, UV dryers, UV LED light sources and exposure machines as well as for quality assurance of industrial UV processes in accordance with the QB/T 2826-2017 standard.
Equipped with a 1.4-inch OLED display, a high measuring rate of 2048 scans per second and a maximum recording time of 32 minutes, the UV Meter / UV Tester delivers precise, fast and reproducible measurement results. During each measurement, the highest recorded value is automatically saved as the maximum value (MAX) and clearly displayed once the measurement is complete.
In automatic mode with the UV Meter / UV Tester, the measurement can be started automatically by an individually adjustable trigger value in the range of 1 ...50 mW/cm2 can be used to start the measurement automatically. This enables targeted detection of UV irradiation precisely from the desired threshold value - ideal for reproducible measurement conditions and process monitoring. An integrated timer enables the UV curing time to be recorded precisely and displayed directly. This function is particularly useful for monitoring and documenting exposure times in time-critical UV applications, such as coating, ink and adhesive curing. This ensures that processes are carried out reproducibly and in accordance with standards.
The compact design makes the UV Meter / UV Tester particularly handy for mobile and stationary applications. The robust, heat-resistant metal housing, in combination with the heat protection cover, enables reliable operation at ambient temperatures of up to 125°C / 257°F. Stored measurement data is retained even in the event of a power failure and is automatically displayed the next time the device is switched on. The internal memory deletes old data automatically when a new measurement is started or manually by pressing and holding the SELECT button in STOP mode. Power is supplied by an integrated, rechargeable lithium battery.... Read More |