| Description | The Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, asThe Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, as well as coaxial cables, such as those used in TV, antenna, and surveillance systems.
Testing is carried out using a two-part system consisting of a main unit and a remote unit, which also allows permanently installed cables to be tested reliably. The most important test procedures include continuity testing of the conductors (pins 1–8), wiring testing to check the correct assignment of the wire pairs, and the detection of short circuits, wiring faults, and split-pair faults. In addition, the shielding of shielded cables is checked. The test range covers cable lengths of up to 305 m, whilst the minimum cable length for split-pair detection is approximately 0.5 m.
Our Cable Detector operates using test signals transmitted between the main unit and the remote unit. The results are displayed via LED indicators. Steady LEDs indicate correct wiring, whilst flashing LEDs indicate faults in the respective wire pairs. Additional status LEDs indicate the type of fault, such as short circuit, miswiring, reversal, or split pair.
The Cable Detector is used in network technology, building cabling, and in IT and communications installations, and is designed for electricians, network technicians, and service technicians to quickly test cable runs.... Read More | The PCE-ATP 1-KIT with 100 swabs included is used to quickly and easily check the cleanliness of surfaces. The Hygiene Tester displays a measurement result on the large LC display after only 10 seconds. The Hygiene Tester's internal memory stores up to 10,000 measured data sets with time and date. The PCE-ATP 1-KIT with 100 swabs included is used to quickly and easily check the cleanliness of surfaces. The Hygiene Tester displays a measurement result on the large LC display after only 10 seconds. The Hygiene Tester's internal memory stores up to 10,000 measured data sets with time and date. The PCE-ATP 1 with the associated PCE-ATP SwapPens, allows a quick detection of food or microbiological residues on all surfaces in contact with the product as an effectiveness test of cleaning and disinfection measures. Quantitative determination of intracellular and extracellular adenosine triphosphate (ATP) is performed in the portable PCE-ATP 1. The measured data from the Hygiene Tester can be stored and further processed after the measurement. The Hygiene Tester is used in the hygiene control in pharmacy, medicine, gastronomy, wholesalers and more.... Read More | The Force Gage is used to precisely check the tension of belts in machines and systems, thereby ensuring optimum power transmission. This Force Gage measures the oscillation frequency of the belt and immediately calculates the belt tension, which is displayed directly in newtons. The measuring rangeThe Force Gage is used to precisely check the tension of belts in machines and systems, thereby ensuring optimum power transmission. This Force Gage measures the oscillation frequency of the belt and immediately calculates the belt tension, which is displayed directly in newtons. The measuring range is between 10 and 680 Hz, with an accuracy of ±1 Hz for frequencies below 100 Hz and ±1% for frequencies above 100 Hz, with a total error of less than 5%.
Special features of the device include the flexible gooseneck sensor for hard-to-reach areas and the option to directly enter the belt length, belt mass and belt width (max. 999.9 mm), which makes the calculation of the belt tension particularly precise. The Force Gage can be switched between displaying the oscillation frequency in Hz and the calculated belt tension in N. It is powered by 3 × AA batteries, making it flexible to use.
This Force Gage is primarily used in the maintenance of conveyor systems, mechanical engineering, the automotive industry and wherever belts need to be tensioned precisely to ensure the performance, safety and service life of the equipment.... Read More | The rain and snow Temperature Sensor is used for reliable detection of precipitation and is used to monitor weather conditions in environmental stations, for irrigation control systems or in industrial plants. The rain and snow Temperature Sensor enables a quick and reliable response to rain or snowThe rain and snow Temperature Sensor is used for reliable detection of precipitation and is used to monitor weather conditions in environmental stations, for irrigation control systems or in industrial plants. The rain and snow Temperature Sensor enables a quick and reliable response to rain or snow. The Temperature Sensor qualitatively detects the presence of precipitation via conductivity and condensation properties and provides the information digitally via RS-485 Modbus RTU and via a potential-free relay output, which can be used to directly switch external devices or controls.
The integrated relay output is designed as a normally open contact and provides galvanic isolation between the Temperature Sensor voltage and the switched circuit. This allows both low-voltage and mains voltage applications to be implemented. The maximum switching capacity of the relay is 250V AC at 1 A or 30V DC at 1 A, making the Temperature Sensor suitable for direct control of controllers, actuators or relays.
The supply voltage of the rain and snow Temperature Sensor is 24 to 30V DC. The compact, corrosion-resistant housing is IP65-rated and designed for surface mounting. An automatic heating function activates at lower temperatures below 0°C / 32°F ambient temperature and heats the Temperature Sensor surface to approximately 40°C / 104°F to prevent ice formation. This ensures that the rain and snow Temperature Sensor works reliably even in frosty conditions. It is mainly used by weather station operators, environmental researchers, in irrigation systems and in industrial applications where precipitation needs to be reliably detected and automated responses implemented.
... Read More | A Thermometer is an indispensable safety device for detecting dangerous carbon monoxide concentrations indoors. It is used wherever CO can occur - for example in homes with gas boilers or fireplaces, in workshops with running engines and in boats, motorhomes or other enclosed spaces with combustion A Thermometer is an indispensable safety device for detecting dangerous carbon monoxide concentrations indoors. It is used wherever CO can occur - for example in homes with gas boilers or fireplaces, in workshops with running engines and in boats, motorhomes or other enclosed spaces with combustion appliances.
The Thermometer records CO values in the range from 0 ... 500 ppm with a high resolution of 1 ppm. The Thermometer also measures relative humidity and temperature, whereby the temperature display can also be switched to Fahrenheit. All measured values are shown on an easy-to-read 2-inch LC display with backlighting.
For even more convenience, the Thermometer has a standby mode that can be activated manually. If no input is made within 60 seconds, the display switches off automatically - but the device remains active. In the event of increased CO values, the Thermometer warns with a visual and acoustic alarm. This is supported by a traffic light function: green for 0 ... 100 ppm, orange for 101 ... 200 ppm and red for 201 ... 500 ppm. As soon as the limit value of 100 ppm is exceeded, an additional acoustic warning signal sounds to indicate a possible hazard. Thanks to the integrated lithium battery, which is conveniently charged via USB-C, the detector is particularly flexible to use.... Read More |