| Description | The Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, asThe Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, as well as coaxial cables, such as those used in TV, antenna, and surveillance systems.
Testing is carried out using a two-part system consisting of a main unit and a remote unit, which also allows permanently installed cables to be tested reliably. The most important test procedures include continuity testing of the conductors (pins 1–8), wiring testing to check the correct assignment of the wire pairs, and the detection of short circuits, wiring faults, and split-pair faults. In addition, the shielding of shielded cables is checked. The test range covers cable lengths of up to 305 m, whilst the minimum cable length for split-pair detection is approximately 0.5 m.
Our Cable Detector operates using test signals transmitted between the main unit and the remote unit. The results are displayed via LED indicators. Steady LEDs indicate correct wiring, whilst flashing LEDs indicate faults in the respective wire pairs. Additional status LEDs indicate the type of fault, such as short circuit, miswiring, reversal, or split pair.
The Cable Detector is used in network technology, building cabling, and in IT and communications installations, and is designed for electricians, network technicians, and service technicians to quickly test cable runs.... Read More | The state-of-the-art Clamp Meter enables precise and comprehensive measurements in the areas of current, voltage, frequency, power, energy flicker and harmonics. It has been specially developed to provide reliable data both in industrial applications and when analyzing photovoltaic or inverter The state-of-the-art Clamp Meter enables precise and comprehensive measurements in the areas of current, voltage, frequency, power, energy flicker and harmonics. It has been specially developed to provide reliable data both in industrial applications and when analyzing photovoltaic or inverter systems.
Simultaneous monitoring of all three phases and the neutral conductor provides a complete picture of the electrical system. The efficiency measurement of inverters allows a detailed analysis of the energy conversion, while the grid signal monitoring continuously detects deviations and faults. This Clamp Meter is therefore an indispensable tool for professional energy analyses.
Thanks to modern communication interfaces such as Wifi, the Clamp Meter can be easily integrated into existing systems and enables wireless analysis of measurement data. The integrated logger function and the memory reliably save all relevant data for later analysis.
An integrated oscilloscope function allows the visual display of signal curves, including inrush currents, and thus supports the analysis of transient phenomena. The 7.8-inch touch display ensures intuitive operation and a clear presentation of all measured values, diagrams and analysis functions. The Clamp Meter fulfils the requirements of IEC 61000-4-30 Class A and thus guarantees standard-compliant analysis of the power quality parameters.
This Clamp Meter combines precision, versatility and modern user-friendliness and is ideal for energy analyses, fault diagnostics and efficiency tests in complex electrical systems.... Read More | Gas Detector / Gas Detection Instrument / Detects natural gas & LPG / Heat and gas sensor / WLAN / Voice announcement / Control via app / Real-time alarm / Easy installation
A Gas Detector / Gas Detection Instrument is an important safety device. It recognizes dangerous gas concentrations in the Gas Detector / Gas Detection Instrument / Detects natural gas & LPG / Heat and gas sensor / WLAN / Voice announcement / Control via app / Real-time alarm / Easy installation
A Gas Detector / Gas Detection Instrument is an important safety device. It recognizes dangerous gas concentrations in the air and sounds the alarm in good time to prevent accidents such as explosions or poisoning. Our Gas Detector / Gas Detection Instrument has been specially developed for use in homes, offices and similar indoor areas. It detects both natural gas (methane) and liquefied petroleum gas (LPG, consisting of propane and butane) and reacts as soon as a certain concentration is exceeded.
Our Gas Detector / Gas Detection Instrument measures gas concentrations in the range of 0 ... 100% of the lower explosion limit (LEL), whereby the alarm is triggered at 6% LEL. The response time is a maximum of 30 seconds and the alarm is triggered at a volume of over 70 decibels. A heat sensor is also integrated, which also triggers an alarm at an ambient temperature of 57°C / 134.6°F.
The detector is equipped with a color LCD display that shows the date and time as well as the gas values, the temperature and the remaining sensor life. A Wi-Fi connection is used to connect to the "Smart Life" app, which can be used to monitor the status of the device worldwide. In the event of an alarm, an acoustic and visual warning, a voice message and a push notification are sent to the smartphone. In addition, a connected valve can be activated automatically to stop the gas supply. The sensor has a service life of five years and the device requires a warm-up time of 180 seconds after switching on. The detector is supplied with 5V/1 A power via micro USB and consumes less than 200 mA.
The installation of the Gas Detector / Gas Detection Instrument depends on the type of gas used: for natural gas, which is lighter than air, the device is installed about 30 cm below the ceiling, for LPG, which is heavier than air, about 30 cm above the floor. The distance to the gas source should be 1.5 to 4 meters / 5 to 13 ft. The Gas Detector / Gas Detection Instrument can be attached either with screws or double-sided adhesive tape. Regular tests, which can also be carried out via the app or manually on the device, ensure that it is working properly.
Overall, the Gas Detector / Gas Detection Instrument offers a modern and reliable solution for the early detection of gas leaks and thus makes a significant contribution to increasing safety in rooms supplied with gas. This model of Gas Detector / Gas Detection Instrument combines modern technology with simple operation and is ideal for private and commercial applications.... Read More | Laboratory Technology for liquids up to 5 l / Stirring speed up to 1600 rpm / Adjustable direction of rotation / Programme mode: up to 6 stirring programmes / 1 stirring position
The Laboratory Technology is an easy-to-use laboratory device that is used for the efficient mixing of liquids. With a 3Laboratory Technology for liquids up to 5 l / Stirring speed up to 1600 rpm / Adjustable direction of rotation / Programme mode: up to 6 stirring programmes / 1 stirring position
The Laboratory Technology is an easy-to-use laboratory device that is used for the efficient mixing of liquids. With a 3.7 inch LCD display and user-friendly controls, the stirring speed, stirring time and direction of rotation can be customized. The stirring speed can be set within a range of 100 ... 1,600 rpm and has an accuracy of ± 10 rpm.
Our Laboratory Technology automatically saves the last set working parameters and up to six individually programmed stirring cycles. This enables a quick restart with the desired settings. The stirrer also has an integrated timer that allows precise time control from one second to 99 hours and 59 minutes.
The use of a brushless motor ensures maintenance-free and quiet operation. The robust acrylic stirring plate measuring 173 × 180 mm provides a stable base for a wide range of stirring tasks, even for longer operating times. The Laboratory Technology can process liquid volumes up to a maximum of 5 litres and is operated via a power supply of AC 100 ... 240V at 50 Hz.
It is a good solution for laboratory work where reliable and reproducible mixing without heating is required. It impresses with its robust design and easy handling in research facilities and industrial laboratories.... Read More | The Nut Runner combines state-of-the-art technology with a robust design and guarantees maximum precision for a wide range of assembly tasks. With its three intelligent operating modes, comprehensive protective functions and practical replaceable battery pack, this Nut Runner is the ideal solution The Nut Runner combines state-of-the-art technology with a robust design and guarantees maximum precision for a wide range of assembly tasks. With its three intelligent operating modes, comprehensive protective functions and practical replaceable battery pack, this Nut Runner is the ideal solution for industrial, workshop and assembly applications.
In torque mode, the desired torque can be set quickly and continuously. The value can be conveniently adjusted using the operating buttons and the screwdriving process begins with a simple pull of the trigger. Angle mode enables controlled tightening not only via the torque, but also via the angle of rotation - perfect for applications that require maximum precision. In addition, Point Mode offers up to six memorizable presets for frequently used torque values. These can be individually configured and called up at the touch of a button during operation - ideal for recurring assembly tasks.
Other highlights of the torque screwdriver include precise torque adjustment with high repeat accuracy, a multi-stage gearbox for reliable power transmission and alarm and monitoring functions that help the user to assess the tightening result. Integrated protective functions such as temperature monitoring prevent overheating and extend the service life of the tool. Thanks to the replaceable battery, uninterrupted work is also guaranteed. Another highlight is the software supplied, which can be used to conveniently read out all the recorded screwdriving data. This allows users to document and analyze torque values, results and process data. The software also allows centralized settings to be made directly on the device.
The Nut Runner is ideal for precise screw connections in mechanical and plant engineering. It also ensures reliable results when assembling wind turbines and steel structures. In the automotive sector, it is an indispensable tool for maintenance and repairs. It can also be used in a wide range of applications in heavy industry and construction.... Read More |