| Description | The Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, asThe Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, as well as coaxial cables, such as those used in TV, antenna, and surveillance systems.
Testing is carried out using a two-part system consisting of a main unit and a remote unit, which also allows permanently installed cables to be tested reliably. The most important test procedures include continuity testing of the conductors (pins 1–8), wiring testing to check the correct assignment of the wire pairs, and the detection of short circuits, wiring faults, and split-pair faults. In addition, the shielding of shielded cables is checked. The test range covers cable lengths of up to 305 m, whilst the minimum cable length for split-pair detection is approximately 0.5 m.
Our Cable Detector operates using test signals transmitted between the main unit and the remote unit. The results are displayed via LED indicators. Steady LEDs indicate correct wiring, whilst flashing LEDs indicate faults in the respective wire pairs. Additional status LEDs indicate the type of fault, such as short circuit, miswiring, reversal, or split pair.
The Cable Detector is used in network technology, building cabling, and in IT and communications installations, and is designed for electricians, network technicians, and service technicians to quickly test cable runs.... Read More | The Condition Monitoring is certified in accordance with IEC 61672-1:2013, Class 1 and is ideally suited for professional use in noise monitoring. With a wide frequency range from 10 Hz to 20 kHz and extensive filter options, the device enables precise measurements in almost all areas of applicationThe Condition Monitoring is certified in accordance with IEC 61672-1:2013, Class 1 and is ideally suited for professional use in noise monitoring. With a wide frequency range from 10 Hz to 20 kHz and extensive filter options, the device enables precise measurements in almost all areas of application. The frequency weightings A, C and Z as well as the time weightings S (Slow), F (Fast) and I (Impulse) are supported in order to always ensure application-appropriate measurement behaviour.
The Condition Monitoring also impresses with its comprehensive connectivity: Ethernet, WiFi and USB Type-C enable flexible and uncomplicated data transfer. The internal 8 GB memory and optional SD cards with up to 64 GB provide sufficient storage capacity for extensive measurement campaigns. The high-resolution 4-inch TFT touch display ensures intuitive and convenient operation. Measured variables such as Lp, Lmax, Lmin, Leq, Lpeak, LN(1-99) and numerous other useful functions are displayed clearly and in detail, enabling professional detailed evaluation of the measurement results with this Condition Monitoring.
Its wide range of applications makes the Condition Monitoring the ideal solution for environmental noise monitoring, traffic noise analysis, noise exposure assessment, occupational health and safety monitoring and airport noise monitoring.
The software included in the scope of delivery extends the functionality considerably: it enables live data reception via Ethernet or WiFi, access to stored measurement data and the export of results as a PDF report or CSV file. In addition, the display of the measurement parameters can be freely configured within the software, allowing customisation to specific analysis requirements.... Read More | Safeguarding sensitive electronic components in manufacturing and handling environments requires precise measurement technology. The Electrical Tester is the indispensable, portable instrument for quickly and reliably checking the surface resistance of materials in ESD-controlled areas.
The Safeguarding sensitive electronic components in manufacturing and handling environments requires precise measurement technology. The Electrical Tester is the indispensable, portable instrument for quickly and reliably checking the surface resistance of materials in ESD-controlled areas.
The Electrical Tester is battery-operated and has integrated parallel electrodes that enable direct testing of the material surface resistance. Thanks to the automatic test voltage selector, the surface resistance tester guarantees maximum measurement accuracy across all relevant ranges. The test voltage automatically switches from 10 V to 100 V as soon as the measured resistance exceeds the value of 1 × 10? ohms.
Two banana sockets allow the connection of external electrodes weighing around 2.25 kg. With these additional components, the Electrical Tester is able to perform professional compliance measurements, such as resistance point-to-point (RTT) or resistance to ground (RTG). The measurement data obtained with this Electrical Tester is essential to ensure adherence to a compliance verification plan (ANSI/ESD S20.20-2007).
The Electrical Tester is ideal for use in electronics production, for testing ESD work mats, workbenches and floor coverings or even in laboratory environments and for quality assurance.... Read More | The Health & Safety is ideal for precisely determining the electrical resistance of materials and surfaces in electronics manufacturing, ESD protection, laboratories and quality control. It is used to reliably determine whether a material is conductive, static dissipative or insulating, thus making The Health & Safety is ideal for precisely determining the electrical resistance of materials and surfaces in electronics manufacturing, ESD protection, laboratories and quality control. It is used to reliably determine whether a material is conductive, static dissipative or insulating, thus making a decisive contribution to the prevention of electrostatic discharge. Thanks to its compact design and ease of use, the device is ideal for both mobile use and stationary measurements and also serves as an ESD measuring device and electrostatic measuring device. Our measuring device covers a wide measuring range from 10³ ? to 10¹? ? and offers a measuring accuracy of 1 decade. The maximum display value is 20 G?; values above this indicate that the measuring range has been exceeded. The temperature measuring range is 0 ... 50°C / 32 °F ... 122°F with a deviation of ±2°C / ±3.6°F. An automatic switch-off after approximately five minutes ensures energy-saving operation, while the integrated backlight and data hold function allow for convenient reading of the measured values.
This Health & Safety has an easy-to-read 2.2-inch LCD display showing temperature, resistance, battery status and measurement mode. Three easy-to-use buttons control all functions, such as power on/off, temperature unit switching and data hold. Power is supplied by a 9 V block battery, allowing the Health & Safety to be operated independently of the mains. The Health & Safety also allows measurements to be taken on irregularly shaped objects and provides a clear evaluation of the measurement results: Values from 10³ to 10? ? indicate conductive materials, 10? to 10¹¹ ? indicate static dissipative properties, and from 10¹² ? onwards, surfaces are considered insulating. The device thus provides a quick and precise assessment of electrostatic properties and ensures greater safety and quality in sensitive production environments.
This measuring device is ideal for specialists in electronics manufacturing, ESD officers, technicians, engineers, testing laboratories and anyone who needs to check surfaces for electrical conductivity. As an ESD measuring device and electrostatic measuring device, it also provides reliable support in complying with electrostatic protection measures.... Read More | The Material Tester is a high-quality measuring instrument designed for calibrating torque sensors and for the precise measurement of the tightening torque of screws and other fasteners. The Material Tester offers a high accuracy of ±1% within the range of 10% ... 100% of the scale and can be The Material Tester is a high-quality measuring instrument designed for calibrating torque sensors and for the precise measurement of the tightening torque of screws and other fasteners. The Material Tester offers a high accuracy of ±1% within the range of 10% ... 100% of the scale and can be operated in both clockwise and anti-clockwise directions.
The Material Tester supports several operating modes, such as Peak Hold, MAX, and real-time measurement. In Peak Hold mode, the maximum value is automatically stored, and the measurement data can be transferred via USB to the software, which also enables a pass/fail evaluation. Tolerance ranges can be set directly on the device, allowing values to be checked quickly. An integrated LED traffic light display shows the measured value at a glance.
The choice between the units Newton-meter (N·m), kilogram-force-centimeter (kgf·cm), and pound-force-inch (lbf·in) enables flexible applications across various industries. With a storage capacity of 2,000 measurement groups and the option of data transfer via USB, the measuring instrument is ideal for use in the mechanical engineering industry and in scientific research facilities.
The Material Tester operates reliably at ambient temperatures of 5 to 40°C / 41 to 104°F and is powered by a 7.2 V NiMH battery, which is optimized for mobile use.... Read More |