| Description | The Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, asThe Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, as well as coaxial cables, such as those used in TV, antenna, and surveillance systems.
Testing is carried out using a two-part system consisting of a main unit and a remote unit, which also allows permanently installed cables to be tested reliably. The most important test procedures include continuity testing of the conductors (pins 1–8), wiring testing to check the correct assignment of the wire pairs, and the detection of short circuits, wiring faults, and split-pair faults. In addition, the shielding of shielded cables is checked. The test range covers cable lengths of up to 305 m, whilst the minimum cable length for split-pair detection is approximately 0.5 m.
Our Cable Detector operates using test signals transmitted between the main unit and the remote unit. The results are displayed via LED indicators. Steady LEDs indicate correct wiring, whilst flashing LEDs indicate faults in the respective wire pairs. Additional status LEDs indicate the type of fault, such as short circuit, miswiring, reversal, or split pair.
The Cable Detector is used in network technology, building cabling, and in IT and communications installations, and is designed for electricians, network technicians, and service technicians to quickly test cable runs.... Read More | Our Cable Detector enables the precise detection and localisation of power lines, wooden beams, metals and other objects such as water-filled plastic pipes in walls, floors and ceilings. Thanks to its versatility, it can be used on various surfaces such as wood, wallpaper, plaster, acoustic walls Our Cable Detector enables the precise detection and localisation of power lines, wooden beams, metals and other objects such as water-filled plastic pipes in walls, floors and ceilings. Thanks to its versatility, it can be used on various surfaces such as wood, wallpaper, plaster, acoustic walls and painted walls.
The device is equipped with a 1.9-inch colour LCD display that provides a clear visual representation of the scan results. A signalling system consisting of coloured LEDs, acoustic cues and directional arrows quickly provides precise information about the proximity and position of the detected object. The LED system indicates green for no obstacles, yellow for nearby objects and red for an obstacle directly under the scanner. The Cable Detector has three detection modes: the metal detection mode for identifying metal objects, the wood detection mode for localising wooden beams and the power mode for detecting live wires. In the metal and power line modes, the device displays the signal strength as a percentage. In wood detection mode, the scanner recognises both the exact centre and the edges of wooden beams, allowing their position and size to be precisely determined.
To further improve the accuracy, the sensitivity can be adjusted in three stages so that the detection can be optimally adapted to the respective conditions. An integrated marking hole makes it possible to mark the drilling site immediately after detection. The Cable Detector also offers automatic calibration, which can be performed on any wall surface. The menu is available in five languages: Russian, English, Portuguese, Japanese as well as Chinese. The automatic switch-off is adjustable and can vary between 5 and 15 minutes or be deactivated completely, depending on requirements. The acoustic signal can also be switched off if required. For reliable and wireless use, the device is equipped with a powerful lithium-ion battery that can be charged quickly and easily via a USB-C port.
With this powerful and user-friendly Cable Detector, obstacles can be reliably detected and construction and renovation work can be carried out safely and efficiently.... Read More | The Clamp Meter is a multifunctional meter for the precise measurement of alternating and direct voltage as well as alternating and direct current that can be measured without direct contact to the line. The Clamp Meter is suitable for measuring resistance, temperature, diodes, continuity, The Clamp Meter is a multifunctional meter for the precise measurement of alternating and direct voltage as well as alternating and direct current that can be measured without direct contact to the line. The Clamp Meter is suitable for measuring resistance, temperature, diodes, continuity, frequencies and capacitance and is particularly useful for diagnosing electrical and electronic components.
For maximum measurement accuracy, the Clamp Meter supports True RMS for non-sinusoidal waveforms and a Low Impedance (LoZ) function to reduce interference. The non-contact voltage test enables reliable detection of voltages in cables and sockets.
The 2-inch LC display ensures clear readability, even under poor lighting conditions and an integrated LED torch makes it easier to work in dark environments. The device also offers automatic and manual measurement range selection, allowing it to be flexibly adapted to different measuring situations. The device also has a practical zero key which enables accurate measurement of low currents, especially when measuring direct current (DC) and ensures the compensation of deviations of the output value. Other functions include overload protection, data hold, min, max and an automatic power-off after 15 minutes to conserve battery life. The power-off can also be deactivated for longer measurements.
Compact and easy to use, the Clamp Meter is ideal for electrical installations, maintenance work and use in automation technology. It enables safe and efficient measurements, often without direct intervention in the circuit.... Read More | Thanks to its wide measurement range and versatile functions, our Decibel Meter is suitable for noise measurements in industry, the environment, occupational health and safety, at events and in research. Our Decibel Meter records and visualises sound levels within a range from 20 to 130 dB in three Thanks to its wide measurement range and versatile functions, our Decibel Meter is suitable for noise measurements in industry, the environment, occupational health and safety, at events and in research. Our Decibel Meter records and visualises sound levels within a range from 20 to 130 dB in three manual measurement ranges and offers various measurement functions such as Hold, Max and Leq value. The Decibel Meter supports time weighting F, S and I as well as frequency weighting A, C and Z and can record sound within a frequency range from 25 to 130 dB.
With operation modes for Leq, 1/1 and 1/3 octave filter measurements, it covers a wide range of measurement requirements. The internal memory function enables automatic storage of up to 12 data groups for octave band measurements. In addition, up to 800 individual measurements and regular measurements can be saved over a period of up to 6 days. These functions make Decibel Meter s indispensable tools in acoustics to ensure both the protection of people and the quality of rooms and products. An RS232 interface can transfer the data via the optional software. An AC output is also available.
The Decibel Meter fulfils several standards, including IEC 61672-1, GB/T3785.2-2010 and IEC 1260-2014, all in class II, making it the ideal choice for standard-compliant measurements. The Decibel Meter is supplied with a windscreen in a practical carrying case.... Read More | UV Meter / UV Tester / External sensor / Hold function / Battery operation / Compact and lightweight / Automatic switch-off
The UV Meter / UV Tester is a compact measuring device for detecting UV-A radiation in the range of 300 ... 390 nm, with a peak wavelength of 365 nm. The UV Meter / UV Tester UV Meter / UV Tester / External sensor / Hold function / Battery operation / Compact and lightweight / Automatic switch-off
The UV Meter / UV Tester is a compact measuring device for detecting UV-A radiation in the range of 300 ... 390 nm, with a peak wavelength of 365 nm. The UV Meter / UV Tester measures radiation intensities from 0 ... 19,999 µW/cm2 with a resolution of 1 µW/cm2 and an accuracy of ± 4% FS. The measuring rate is one measurement per second, a hold function enables the current value to be recorded.
The UV Meter / UV Tester has an easy-to-read 1.4-inch LED display, a battery indicator and automatic switch-off after 4 minutes. The external sensor measures 78 × 38.5 × 15.5 mm and is connected via a 1 m cable - ideal for flexible applications. It is powered by two 1.5V AA batteries.
The UV Meter / UV Tester is suitable for numerous applications such as UV curing in industry, UV controls in medicine, occupational safety measurements and for laboratory and environmental technology. Thanks to the accuracy of the UVA radiation meter and its ease of use, the UV Meter / UV Tester is a reliable tool for many professional applications.... Read More |