| Description | The Health & Safety is ideal for precisely determining the electrical resistance of materials and surfaces in electronics manufacturing, ESD protection, laboratories and quality control. It is used to reliably determine whether a material is conductive, static dissipative or insulating, thus making The Health & Safety is ideal for precisely determining the electrical resistance of materials and surfaces in electronics manufacturing, ESD protection, laboratories and quality control. It is used to reliably determine whether a material is conductive, static dissipative or insulating, thus making a decisive contribution to the prevention of electrostatic discharge. Thanks to its compact design and ease of use, the device is ideal for both mobile use and stationary measurements and also serves as an ESD measuring device and electrostatic measuring device. Our measuring device covers a wide measuring range from 10³ ? to 10¹? ? and offers a measuring accuracy of 1 decade. The maximum display value is 20 G?; values above this indicate that the measuring range has been exceeded. The temperature measuring range is 0 ... 50°C / 32 °F ... 122°F with a deviation of ±2°C / ±3.6°F. An automatic switch-off after approximately five minutes ensures energy-saving operation, while the integrated backlight and data hold function allow for convenient reading of the measured values.
This Health & Safety has an easy-to-read 2.2-inch LCD display showing temperature, resistance, battery status and measurement mode. Three easy-to-use buttons control all functions, such as power on/off, temperature unit switching and data hold. Power is supplied by a 9 V block battery, allowing the Health & Safety to be operated independently of the mains. The Health & Safety also allows measurements to be taken on irregularly shaped objects and provides a clear evaluation of the measurement results: Values from 10³ to 10? ? indicate conductive materials, 10? to 10¹¹ ? indicate static dissipative properties, and from 10¹² ? onwards, surfaces are considered insulating. The device thus provides a quick and precise assessment of electrostatic properties and ensures greater safety and quality in sensitive production environments.
This measuring device is ideal for specialists in electronics manufacturing, ESD officers, technicians, engineers, testing laboratories and anyone who needs to check surfaces for electrical conductivity. As an ESD measuring device and electrostatic measuring device, it also provides reliable support in complying with electrostatic protection measures.... Read More | The Accelerometer offers a reliable solution for monitoring vibrations in industrial machinery. The device can measure and output either acceleration, velocity, or displacement. The desired measurement parameter is conveniently set using integrated DIP switches. The device operates in the frequency The Accelerometer offers a reliable solution for monitoring vibrations in industrial machinery. The device can measure and output either acceleration, velocity, or displacement. The desired measurement parameter is conveniently set using integrated DIP switches. The device operates in the frequency range of 10 Hz to 1000 Hz and meets the requirements of ISO 2954. The measurement ranges are 0.5 to 199.9 m/s² for acceleration, 0.5 to 199.9 mm/s for velocity, and 0 to 1.999 mm for displacement. The high resolution of 0.1 m/s², 0.1 mm/s, and 0.001 mm enables precise measurement of even the smallest vibrations. Accuracy is ±5% + 2 digits under typical operating conditions.
The Accelerometer supports both RMS and peak-to-peak measurements, offering versatile analysis options. The analogue 4–20 mA interface enables easy integration into existing monitoring systems. Separate vibration measurement is carried out via a robust probe with a magnetic mount, ensuring flexible and secure attachment to the measurement object. The Accelerometer’s housing is rated to IP63, and the probe to IP60. Power is supplied via 12–30 V DC, allowing the Accelerometer to be integrated into a wide variety of industrial environments.
Thanks to zero and span adjustment, the Accelerometer can be optimally adapted to the respective measurement requirements. Operation is particularly user-friendly thanks to the compact design and ease of use. The Accelerometer is ideal for condition monitoring of machinery, preventive maintenance, and continuous process monitoring in industry. Typical applications include the monitoring of motors, pumps, fans, and other rotating machinery in production, maintenance, and quality assurance.... Read More | The Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, asThe Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, as well as coaxial cables, such as those used in TV, antenna, and surveillance systems.
Testing is carried out using a two-part system consisting of a main unit and a remote unit, which also allows permanently installed cables to be tested reliably. The most important test procedures include continuity testing of the conductors (pins 1–8), wiring testing to check the correct assignment of the wire pairs, and the detection of short circuits, wiring faults, and split-pair faults. In addition, the shielding of shielded cables is checked. The test range covers cable lengths of up to 305 m, whilst the minimum cable length for split-pair detection is approximately 0.5 m.
Our Cable Detector operates using test signals transmitted between the main unit and the remote unit. The results are displayed via LED indicators. Steady LEDs indicate correct wiring, whilst flashing LEDs indicate faults in the respective wire pairs. Additional status LEDs indicate the type of fault, such as short circuit, miswiring, reversal, or split pair.
The Cable Detector is used in network technology, building cabling, and in IT and communications installations, and is designed for electricians, network technicians, and service technicians to quickly test cable runs.... Read More | The Light Sensor is ideal for monitoring light intensities in greenhouses, industrial facilities or smart farming systems, enabling precise control of lighting and energy use. The Light Sensor detects light intensities from 0 to 65,535 lx and delivers the measured values via a digital RS-485 Modbus The Light Sensor is ideal for monitoring light intensities in greenhouses, industrial facilities or smart farming systems, enabling precise control of lighting and energy use. The Light Sensor detects light intensities from 0 to 65,535 lx and delivers the measured values via a digital RS-485 Modbus RTU output. The accuracy is ±7% FS at 25°C / 77°F, the response time is ?1 s, the supply voltage is 10 to 30V DC, and the robust, moisture-protected housing allows for indoor and outdoor use.
The Light Sensor is primarily used by greenhouse operators, environmental researchers, and companies in the smart farming sector, as well as industrial plants that want to reliably monitor light intensities and implement automated controls.... Read More | UV Meter / UV Tester / Internal sensor / Hold function / Battery operation / Compact and lightweight / Automatic switch-off
The UV Meter / UV Tester is a compact measuring device for detecting UV-A radiation in the range of 300 ... 390 nm, with a peak wavelength of 365 nm. The UV Meter / UV Tester UV Meter / UV Tester / Internal sensor / Hold function / Battery operation / Compact and lightweight / Automatic switch-off
The UV Meter / UV Tester is a compact measuring device for detecting UV-A radiation in the range of 300 ... 390 nm, with a peak wavelength of 365 nm. The UV Meter / UV Tester measures radiation intensities from 0 ... 19,999 µW/cm2 with a resolution of 1 µW/cm2 and an accuracy of ± 4% FS. The measuring rate is one measurement per second, a hold function enables the current value to be recorded.
The UV Meter / UV Tester has an integrated sensor, an easy-to-read 1.4-inch LED display, a battery indicator and automatic switch-off after 4 minutes to save energy. It is powered by two 1.5V AA batteries, which makes mobile use particularly convenient.
The UV Meter / UV Tester is ideal for applications such as UV curing in industry, UV controls in medicine, occupational safety measurements and laboratory and environmental technology. The combination of integrated sensor, high accuracy and user-friendly design makes it a reliable tool for a wide range of professional requirements.... Read More |