| Description | Product usage adviceIncubation temperature: 20-37 °C / 68-100 °FResponse time: Moderate (up to 30 minutes) at 20-37°CShelf life: 24 monthsActive ingredients and principle of actionIn different buffer solutions (pH = 9.5), different additives were added as required, and the active Product usage adviceIncubation temperature: 20-37 °C / 68-100 °FResponse time: Moderate (up to 30 minutes) at 20-37°CShelf life: 24 monthsActive ingredients and principle of actionIn different buffer solutions (pH = 9.5), different additives were added as required, and the active ingredient p-nitrophenyl phosphate (pNPP) was dissolved.Alkaline phosphatase transfers phosphate residues to acceptors. Under alkaline conditions, a yellow color will appear due to the formation of nitrophenols.Main advantageHigh absorbance yield comparable to freshly dissolved pNPP tabletsWide measuring rangelow background signalLow blank drift during long-term storage (<0.18 AU over 24 months)High color stability after quenching the reaction with used stop solutionStorage, Shipping and Filling InformationStore at 2-8°C protected from light. Under these conditions, the expiration date printed on the label is valid for unopened bottles.Spontaneous decay increases the background. The rate of decay increases if stored at room temperature. Therefore, storage and transport at room temperature should be avoided. However, the activity of the solution was not affected by storage at room temperature. The solution remains valid beyond the due date, but some applications, especially those that include visual assessments, may be hindered by increased background.Contaminated or leaked substrate solutions from damaged bottles should not be reused and must be destroyed.Ship in an isolated container with some refrigerated bags.The following bottling instructions should be considered:Work in a dust-free and dark room.Keep the solution as cool as possible.Avoid contact of solution with any metal parts.Thoroughly clean all instruments and containers.Wear powder-free gloves when bottling.Close the bottle immediately to minimize the effects of light and dust.Use an opaque, clean bottle made of HDPE or PP.General instructions for use in ELISAOnly qualified laboratory staff familiar with the basics of immunological methods should use these solutions.Substrate solutions can be used in qualitative and quantitative ELISA procedures.When using a 96-well microtiter plate, it is recommended to add 100 µL of pure substrate per well after incubation and washing. After substrate incubation, the reaction can be stopped and photometric measurements can be performed. Using a higher incubation temperature (37°C) may shorten the incubation time.stop 2. Further increases in signal cannot be safely ruled out using other commercially available stopping solutions. The addition of stop solution did not change the general shape of the spectrum.Unstopped and stopped solutions should be measured at 405 nm, background corrected: should be measured at 620 nm.WasteDisposal of waste must comply with national and local laws and regulations. Disposal of packaging must comply with national and local disposal regulations... Read More | Product introduction：Aladdin ® SE is a kind of fluorescent dye with amino reactive activity. The SE group of these dyes can react with the amino group to produce a stable amide bond. Compared with other similar dyes on the market, aladdin ® is a new generation of fluorescent dyes Product introduction：Aladdin ® SE is a kind of fluorescent dye with amino reactive activity. The SE group of these dyes can react with the amino group to produce a stable amide bond. Compared with other similar dyes on the market, aladdin ® is a new generation of fluorescent dyes with stronger stability, better water solubility and better fluorescence intensity. Product parameters： Absmax/Em(nm)：648/664；Absmax/Em(nm)：0.03；Extinction coefficient(ε)：240000；Optimal DOL(IgG)：3-6； Usage:1. Experimental materials(1) IgG: IgG must not contain amine chemicals that can react with dyes, such as amino acids, Tris, BSA, gelatin, etc. If IgG contains such chemicals, PBS buffer with pH~7.4 should be used for pre dialysis treatment. The presence of azide compounds does not affect the labeling reaction.(2) Anhydrous DMSO(3) NaHCO3(4) Sephadex gel G-25 dialysis column(5) PBS buffer (pH~7.4)(6) NaN3(7) BSA2. Marking methods and steps(1) Prepare to label antibodiesDilute the antibody with 0.1 M NaHCO3 solution (pH~8.3) to a final concentration of 2.5 mg/mL. If the product is pre diluted with phosphate buffer, such as PBS buffer (without amino compounds), approximately 1/10 volume of 1M NaHCO3 mother liquor can be directly added to the buffer to achieve a final NaHCO3 concentration of 0.1 M.Note: When the protein concentration is 2.5 mg/mL, the labeling efficiency is approximately 35%. Protein concentrations below 2.5 mg/mL can also be used for labeling, but the labeling efficiency will decrease. When the protein concentration is higher than 5 mg/mL, the labeling efficiency may be higher. Due to differences in buffer and protein purity, more precise labeling efficiency is determined by practical operating conditions. If the protein concentration is too low, it can be concentrated by ultrafiltration.(2) Prepare dye storage solutionPreheat one tube at room temperature µ YF of Mole ® SE, add 0.1 mL of anhydrous DMSO to the tube, thoroughly vortex dissolve the dye, and prepare a dye storage solution with a concentration of 10 mM. If a trace amount of protein is used for labeling reactions, the dye needs to be diluted to a lower concentration.Note: a The remaining dye storage solution should be stored at a low temperature of -20 ℃ for future use. If anhydrous DMSO is used to prepare dye storage solution, the dye can be stored for at least one month.b. Dyes can also be prepared with deionized water, but due to the slow hydrolysis of dyes in water, it is best to prepare water based storage solutions for immediate use.(3) Mark reaction stepsa. Stir or vortex the protein solution, gradually adding 15-25 drops µ L dye storage solution (10 mM), with a molar ratio of dye/protein in the range of 9:1 to 15:1. YF ® Please refer to the table above for the range of DOL (number of dyes bound to each protein molecule) for SE labeled IgG antibodies.b. Stir the reaction at room temperature for 1 hour, and for trace labeling, shake and incubate on a shaker for 1 hour.Note: At the same time of the binding reaction, proceed to step 2 (4) to balance the dextran gel G-25 dialysis column.(4) Isolation of marker proteins from reaction solutiona. PBS buffer (pH~7.4) was used to balance the dextran gel G-25 dialysis column (10 mm × 300 mm).b. Add the reaction solution from step 3 (b) to the column and elute with 1 x PBS buffer.The first washed out chromophore is a dye protein complex.Note: a For small-scale labeling reactions, in order to avoid excessive dilution of the product, ultrafiltration devices can be used to remove free dyes from the complex.b. After the binding reaction is completed, if the dye protein complex is not separated in time, 50 can be added µ Terminate the reaction with L 1M lysine. In most cases, this operation is not necessary because the remaining unreacted dyes have been fully hydrolyzed at the end of the reaction.3. Determine DOL(1) The determination of protein concentration and antibody concentration can be calculated using the following formula:C (mg/mL)={[A280- (Amax x x Cf)]/1.4} x dilution factor;a. C refers to the concentration of antibodies collected in the experiment;b. Dilution factor refers to the dilution factor used in photometric measurements;c. A280 and Amax refer to the absorbance at 280 nm and the absorbance at the absorption wavelength, respectively;d. Cf is the correction factor, YF ® Please refer to the table above for the Cf value of SE dyes;Note: The protein solution eluted through the column may have a high concentration when used directly for absorbance detection, so it needs to be diluted to approximately 0.1 mg/mL. The dilution factor (i.e. dilution factor) needs to be determined from the initial number of antibodies (e.g. 5 mg) and the overall elution of protein solutionEstimate based on the product.(2) Estimation of DOLDOL is calculated using the following equation:DOL=(Amax x x Mwt x Dilution Factor)/（ ε X C)a. Amax, dilution factor, C value has been clearly defined in 3 (1);b. Mwt refers to the molecular weight of IgG (150000);C. c ε It's YF ® The molar absorption coefficient of SE, refer to the table on the first page;d. Mark YF ® The optimal DOL value for SE IgG antibodies can be found in the table on the first page. Although DOL values may fluctuate, good experimental results can also be achieved.Matters needing attention：1. if the labeled protein needs long-term storage, it is recommended to add 5-10 mg/ml BSA and 0.01-0.03% NaN3 to prevent protein denaturation and microbial breeding. Store at 4 ℃ away from light. If glycerol with a final concentration of 50% is added, it can be stored at -20 ℃. It can be stably stored for more than one year. 2. keep away from light during operation. The mixing speed should be appropriate to avoid bubbles. 3. when installing the chromatographic column, try to make the column body uniform, the column surface flat, and free of bubbles and cracks. 4. pay attention to adding the sample when the column top buffer is tangent to the gel plane. When eluting, add the eluent when the sample is tangent to the gel plane. 5. other factors affecting the labeling efficiency also include temperature, reaction time, pH, the amount of fluorescent dye and protein, etc., which should be controlled. 6. for your safety and health, please wear laboratory clothes and disposable gloves.Scope of application：Protein nucleic acid labeling dye... Read More | Cardiolipin is a unique phospholipid present in the inner mitochondrial membrane, which makes up to 20% of total lipids. It is a non-bilayer anionic phospholipid, which has four acyl chains and small headgroupHeart CA has been used as a standard stock solution for its quantitative analysis using Cardiolipin is a unique phospholipid present in the inner mitochondrial membrane, which makes up to 20% of total lipids. It is a non-bilayer anionic phospholipid, which has four acyl chains and small headgroupHeart CA has been used as a standard stock solution for its quantitative analysis using liquid chromatography?mass spectrometry (LC-MS)/MS. It has also been used for liposome preparation... Read More | Inquire | Laccase is an enzyme, produced by ericoid mycorrhiza and ectomycorrhiza fungi. It belongs to the group of polyphenol oxidases. Laccase is also present in plants and bacteria.Laccase from Trametes versicolor has been used: to assess the use of four laccase-producing strains in waste water treatment Laccase is an enzyme, produced by ericoid mycorrhiza and ectomycorrhiza fungi. It belongs to the group of polyphenol oxidases. Laccase is also present in plants and bacteria.Laccase from Trametes versicolor has been used: to assess the use of four laccase-producing strains in waste water treatment in laccase assay in screening the lignolsSome of the enzymatic actions of laccase are associated with sporulation, detoxification, morphogenesis, melanin polymerization and it offers protection to spore coat. Laccase can catalyse a number of substrates including medicinal drugs and halogenated pesticides. It utilizes oxygen for its catalysis. For these reasons, it might be useful in the biological degradation of micropollutants in wastewater treatment. Laccase catalyzes the oxidation of phenol containing compounds, including lignin, through the reduction of oxygen to water. The presence of mediators will allow the oxidation of non-phenlic compounds as well. The primary function of laccase is to degrade lignin in fungi... Read More |