| Description | In the process of large-scale mRNA production, the transcription template needs to be removed after transcription. DNase I can randomly decompose single-stranded or double-stranded DNA to the same degree to generate oligonucleotides with 5'-P ends. Under Mg2+ conditions, DNase I can cut double-In the process of large-scale mRNA production, the transcription template needs to be removed after transcription. DNase I can randomly decompose single-stranded or double-stranded DNA to the same degree to generate oligonucleotides with 5'-P ends. Under Mg2+ conditions, DNase I can cut double-stranded DNA at will.DNase I (Deoxyribonuclease I, deoxyribonuclease I) was originally isolated from bovine pancreas, with a molecular weight of about 39 kD. Has a 5'-P terminal oligonucleotide. DNase I hydrolyzes single-stranded or double-stranded DNA, its activity is very dependent on the level of Ca2+, and can be activated by Mg2+ or Mn2+.This product is a GMP-grade recombinant DNase I expressed by large-scale fermentation of Pichia pastoris. It is produced with medicinal specifications raw materials and strictly controlled host protein residues, nucleic acid residues, etc., and conforms to GMP standard product production and quality management procedures to ensure the production process And all raw and auxiliary materials can be traced back.Quality requirements Project Standard Method Exterior Clear liquid Visual inspection Visible foreign body Compliance Chinese Pharmacopoeia 2020 Edition Fourth Part 1 Lamp Inspection Method (General Rule 0904) pH value 7.0-8.0 Chinese Pharmacopoeia 2020 Edition Part IV pH Determination Method (General Principle 0631) active 1.8KUml-2.2KU/ml 004 Plasmid DNA degradation method Purity ≥95% Chinese Pharmacopoeia 2020 Edition Part IV High Performance Liquid Chromatography (General Principle 0512) RNase residue Degradation of 293-RNA does not exceed 10% 2U enzyme and 293-RNA. Incubate at 37°C for 1h Bacterial endotoxin content ≤10 EU/mg Chinese Pharmacopoeia 2020 Edition Fourth Gel Limit Test Method (General Rule 1143) Exogenous DNA residue ≤100 pg/mg Fluorescence quantitative PCR Host protein residue ≤50 ppm Chinese Pharmacopoeia 2020 Edition Part IV Method for the Determination of Bacterial Protein Residues (General Rule 3414) Mycoplasma detection Feminine Mycoplasma detection kit Heavy metal residue ≤10 ppm Chinese Pharmacopoeia 2020 Edition Fourth Heavy Metal Inspection Method (General Principle 0821) Follow the following specifications for production1. ISO 9001:2015, certified facility.2. "GMP Appendix-Cell Therapy Products" State Drug Administration.3. "General Introduction to Human Gene Therapy-Chinese Pharmacopoeia 2020" National Pharmacopoeia Commission.4. USP Chapter <1043>, Ancillary Materials for Cell, Gene, and Tissue-Engineered Products are used as excipients in cell therapy, gene therapy and tissue engineering products.5. USP Chapter <92>, Growth Factors and Cytokines Used in Cell Therapy Manufacturing Cytokines and growth factors used in the production of cell therapy products.6.Ph. Eur. General Chapter 5.2.12, Raw Materials of Biological Origin for the Production of Cell-based and Gene Therapy Medicinal Products.Product Usage1. Prepare an RNA sample without DNA.2. In the RNA sample before the RT-PCR reaction, remove possible DNA contamination such as genomic DNA.3. In vitro T7, T3, SP6 and other RNA polymerases catalyze the removal of DNA template after in vitro transcription.4. Used for Footprinting (Footprinting) to analyze DNA-protein interactions.5. Used with DNA Polymerase I for nick translation.6. In the presence of divalent manganese ions, the DNA is fragmented to generate a library of random DNA fragments.7. In the apoptosis TUNEL test, part of the genomic DNA is sheared as a positive control.Preservation system10 mM Tris-HCl (pH7.6); 2 mM CaCl2; 50% (v/v) Glycerol.Precautions1. Optimal pH: 7.0-8.02. Activator: DNase I requires divalent cations to achieve maximum activity.3. Inhibitors: EDTA, EGTA, SDS.4. Specificity: double-strand specific endonuclease that degrades DNA.5. Put the enzyme on ice during use, and store it at -20°C after use... Read More | 2x Taq MasterMix is a premixed system composed of Taq DNA Polymerase, Mg2+, dNTPs, PCR stabilizers, and enhancers. The pre prepared PCR mixture makes the operation simpler and faster, and can minimize human error and contamination to the greatest extent possible. The original MasterMix formula 2x Taq MasterMix is a premixed system composed of Taq DNA Polymerase, Mg2+, dNTPs, PCR stabilizers, and enhancers. The pre prepared PCR mixture makes the operation simpler and faster, and can minimize human error and contamination to the greatest extent possible. The original MasterMix formula results in high yield, strong repeatability, and good stability of amplified products. This product does not contain dyes. After the PCR program is completed, an appropriate amount of sample buffer can be added as needed for electrophoresis operation. The amplified PCR product has an "A" base attached to the 3 'end, making it suitable for direct use in T/A cloning. Mainly suitable for PCR amplification of DNA, DNA sequencing and other experiments.Quality control: T665627Component5mlStorageT665627A2×Taq MasterMix5×1ml-20℃. Avoid freeze/thaw cycle.T665627BddH₂O5×1ml-20℃. Avoid freeze/thaw cycle.Notes: 2×Taq MasterMix contains Taq DNA Polymerase, 3mM MgCl2 and 400µM each dNTP After testing, there was no exogenous nuclease activity; PCR method for detecting residual DNA without host; Can effectively amplify single copy genes from multiple genomes.Usage:The following is an example of a PCR reaction system and reaction conditions for amplifying a 1 kb fragment using human genomic DNA as a template. In practical operation, corresponding improvements and optimizations should be made based on the template, primer structure, and target fragment size.1. PCR reaction systemReagent50 µlReaction systemFinal concentration2×Taq MasterMix25 µl1×Forward Primer，10 µM2 µl0.4 µMReverse Primer，10 µM2 µl0.4 µMTemplate DNA<0.5 µg<0.5 µg/50 µlddH2Oup to 50 µl/Attention: The primer concentration should be between 0.1 and 1.0 as the final concentration µ M serves as a reference for setting the range. In the case of low amplification efficiency, the concentration of primers can be increased; When non-specific reactions occur, the primer concentration can be reduced to optimize the reaction system.2. PCR reaction conditionsStepTemperatureTime/Pre denaturation95℃2 min/Denaturation94℃30 s25-35 cyclesAnneal55-65℃30 s25-35 cyclesExtend72℃30 s25-35 cyclesFinally extended72℃2 min/Attention:1) In general experiments, if the annealing temperature is 5 ℃ lower than the melting temperature Tm of the amplification primer, and the ideal amplification efficiency cannot be achieved, the annealing temperature should be appropriately reduced; When non-specific reactions occur, increase the annealing temperature to optimize the reaction conditions.2) The extension time should be set according to the size of the amplified fragment. The amplification efficiency of Taq DNA Polymerase in this product is 2 kb/min.3) The number of cycles can be set based on the downstream application of the amplification product. If the number of cycles is too small, the amplification amount is insufficient; If there are too many cycles, the probability of mismatches will increase, and non-specific backgrounds will be severe. So, while ensuring product yield, the number of cycles should be minimized as much as possible... Read More | Product introduction：Aladdin ® SE is a kind of fluorescent dye with amino reactive activity. The SE group of these dyes can react with the amino group to produce a stable amide bond. Compared with other similar dyes on the market, aladdin ® is a new generation of fluorescent dyes Product introduction：Aladdin ® SE is a kind of fluorescent dye with amino reactive activity. The SE group of these dyes can react with the amino group to produce a stable amide bond. Compared with other similar dyes on the market, aladdin ® is a new generation of fluorescent dyes with stronger stability, better water solubility and better fluorescence intensity. Product parameters： Absmax/Em(nm)：648/664；Absmax/Em(nm)：0.03；Extinction coefficient(ε)：240000；Optimal DOL(IgG)：3-6； Usage:1. Experimental materials(1) IgG: IgG must not contain amine chemicals that can react with dyes, such as amino acids, Tris, BSA, gelatin, etc. If IgG contains such chemicals, PBS buffer with pH~7.4 should be used for pre dialysis treatment. The presence of azide compounds does not affect the labeling reaction.(2) Anhydrous DMSO(3) NaHCO3(4) Sephadex gel G-25 dialysis column(5) PBS buffer (pH~7.4)(6) NaN3(7) BSA2. Marking methods and steps(1) Prepare to label antibodiesDilute the antibody with 0.1 M NaHCO3 solution (pH~8.3) to a final concentration of 2.5 mg/mL. If the product is pre diluted with phosphate buffer, such as PBS buffer (without amino compounds), approximately 1/10 volume of 1M NaHCO3 mother liquor can be directly added to the buffer to achieve a final NaHCO3 concentration of 0.1 M.Note: When the protein concentration is 2.5 mg/mL, the labeling efficiency is approximately 35%. Protein concentrations below 2.5 mg/mL can also be used for labeling, but the labeling efficiency will decrease. When the protein concentration is higher than 5 mg/mL, the labeling efficiency may be higher. Due to differences in buffer and protein purity, more precise labeling efficiency is determined by practical operating conditions. If the protein concentration is too low, it can be concentrated by ultrafiltration.(2) Prepare dye storage solutionPreheat one tube at room temperature µ YF of Mole ® SE, add 0.1 mL of anhydrous DMSO to the tube, thoroughly vortex dissolve the dye, and prepare a dye storage solution with a concentration of 10 mM. If a trace amount of protein is used for labeling reactions, the dye needs to be diluted to a lower concentration.Note: a The remaining dye storage solution should be stored at a low temperature of -20 ℃ for future use. If anhydrous DMSO is used to prepare dye storage solution, the dye can be stored for at least one month.b. Dyes can also be prepared with deionized water, but due to the slow hydrolysis of dyes in water, it is best to prepare water based storage solutions for immediate use.(3) Mark reaction stepsa. Stir or vortex the protein solution, gradually adding 15-25 drops µ L dye storage solution (10 mM), with a molar ratio of dye/protein in the range of 9:1 to 15:1. YF ® Please refer to the table above for the range of DOL (number of dyes bound to each protein molecule) for SE labeled IgG antibodies.b. Stir the reaction at room temperature for 1 hour, and for trace labeling, shake and incubate on a shaker for 1 hour.Note: At the same time of the binding reaction, proceed to step 2 (4) to balance the dextran gel G-25 dialysis column.(4) Isolation of marker proteins from reaction solutiona. PBS buffer (pH~7.4) was used to balance the dextran gel G-25 dialysis column (10 mm × 300 mm).b. Add the reaction solution from step 3 (b) to the column and elute with 1 x PBS buffer.The first washed out chromophore is a dye protein complex.Note: a For small-scale labeling reactions, in order to avoid excessive dilution of the product, ultrafiltration devices can be used to remove free dyes from the complex.b. After the binding reaction is completed, if the dye protein complex is not separated in time, 50 can be added µ Terminate the reaction with L 1M lysine. In most cases, this operation is not necessary because the remaining unreacted dyes have been fully hydrolyzed at the end of the reaction.3. Determine DOL(1) The determination of protein concentration and antibody concentration can be calculated using the following formula:C (mg/mL)={[A280- (Amax x x Cf)]/1.4} x dilution factor;a. C refers to the concentration of antibodies collected in the experiment;b. Dilution factor refers to the dilution factor used in photometric measurements;c. A280 and Amax refer to the absorbance at 280 nm and the absorbance at the absorption wavelength, respectively;d. Cf is the correction factor, YF ® Please refer to the table above for the Cf value of SE dyes;Note: The protein solution eluted through the column may have a high concentration when used directly for absorbance detection, so it needs to be diluted to approximately 0.1 mg/mL. The dilution factor (i.e. dilution factor) needs to be determined from the initial number of antibodies (e.g. 5 mg) and the overall elution of protein solutionEstimate based on the product.(2) Estimation of DOLDOL is calculated using the following equation:DOL=(Amax x x Mwt x Dilution Factor)/（ ε X C)a. Amax, dilution factor, C value has been clearly defined in 3 (1);b. Mwt refers to the molecular weight of IgG (150000);C. c ε It's YF ® The molar absorption coefficient of SE, refer to the table on the first page;d. Mark YF ® The optimal DOL value for SE IgG antibodies can be found in the table on the first page. Although DOL values may fluctuate, good experimental results can also be achieved.Matters needing attention：1. if the labeled protein needs long-term storage, it is recommended to add 5-10 mg/ml BSA and 0.01-0.03% NaN3 to prevent protein denaturation and microbial breeding. Store at 4 ℃ away from light. If glycerol with a final concentration of 50% is added, it can be stored at -20 ℃. It can be stably stored for more than one year. 2. keep away from light during operation. The mixing speed should be appropriate to avoid bubbles. 3. when installing the chromatographic column, try to make the column body uniform, the column surface flat, and free of bubbles and cracks. 4. pay attention to adding the sample when the column top buffer is tangent to the gel plane. When eluting, add the eluent when the sample is tangent to the gel plane. 5. other factors affecting the labeling efficiency also include temperature, reaction time, pH, the amount of fluorescent dye and protein, etc., which should be controlled. 6. for your safety and health, please wear laboratory clothes and disposable gloves.Scope of application：Protein nucleic acid labeling dye... Read More | Purity> 95 % by SDS-PAGE and HPLC analysesFunctionThis receptor has essential roles in the regulation of IgE production and in the differentiation of B-cells (it is a B-cell-specific antigen) | Purity: >90%, by SDS-PAGE visualized with Coomassie® Blue Staining. Function：Actin cross-linking/gelling protein (By similarity). Involved in calcium interactions and contractile properties of the cell that may contribute to replicative senescence |