| Description | Product contentG665760Component5 mLStorageG665760A2×GoldStar Probe Mixture5×1 mL-20℃. Avoid freeze/thaw cycle.G665760B50×Low ROX200 µL-20℃. Avoid freeze/thaw cycle.G665760CddH₂O5×1 mL-20℃. Avoid freeze/thaw cycle. Product Introduction GoldStar Probe Product contentG665760Component5 mLStorageG665760A2×GoldStar Probe Mixture5×1 mL-20℃. Avoid freeze/thaw cycle.G665760B50×Low ROX200 µL-20℃. Avoid freeze/thaw cycle.G665760CddH₂O5×1 mL-20℃. Avoid freeze/thaw cycle. Product Introduction GoldStar Probe Mixture is a premixed system for real-time fluorescence quantitative PCR by probe method (TaqMan, Molecular Beacon, etc.), with a concentration of 2×, containing GoldStar Taq DNA Polymerase, PCR Buffer, dNTPs and Mg2+, which is easy and convenient to operate. It is mainly used for genomic DNA target sequence and RNA reverse transcription cDNA target sequence detection, such as gene expression analysis, copy number analysis, SNP genotype analysis, etc. It is suitable for fluorescence quantification by different types of probe methods. GoldStar Taq DNA Polymerase is a chemically modified, new and highly efficient hot-start enzyme, which has no polymerase activity at room temperature and effectively avoids non-specific amplification caused by non-specific binding of primers and templates or primer dimerization at room temperature, and the activation of the enzyme must be incubated at 95℃ for 10 minutes. The unique combination of PCR buffer system and hot-start enzyme significantly improves the amplification efficiency of PCR with stronger fluorescent signal and higher sensitivity to detect single-copy templates. A wider linear range and more accurate quantification of target genes can be obtained with this product. It is suitable for all fluorescent quantitative PCR instruments that do not require ROX as a calibration dye.ROX dye is used to correct the fluorescence signal error generated between wells of a quantitative PCR instrument, and is generally used in Real Time PCR amplifiers from ABI, Stratagene, and others. The excitation optics vary from instrument to instrument, so the concentration of ROX dye must be matched to the corresponding fluorescence quantitative PCR instrument.Instruments that do not require ROX calibration (G665832) :Roche LightCycler 480, Roche LightCyler 96, Bio-rad iCyler iQ, iQ5, CFX96 and others.Instruments requiring Low ROX calibration (G665832) :ABI Prism7500/7500 Fast, QuantStudio®3 System, QuantStudio®5 System, QuantStudio®6 Flex System, QuantStudio®7 Flex System, ViiA7 system. Stratagene Mx3000/Mx3005P, Corbett Rotor Gene 3000, and more.Instruments requiring High ROX calibration (G665832) :ABI Prism 7000/7300/7700/7900, Eppendorf, ABI Step One/Step One Plus, and others.matters needing attention1. Before use, please mix gently by turning up and down, avoid foaming as much as possible, and use after brief centrifugation.2. Avoid repeated freezing and thawing of this product, repeated freezing and thawing may degrade the product performance. This product can be stored for long term at -20℃, protected from light. If frequent use is required within a short period of time, it can be stored at 2-8℃.UsageThe following examples are conventional PCR reaction systems and reaction conditions, which should be improved and optimized according to the template, primer structure and target fragment size in actual operation.1.PCR reaction systemreagents50µl reaction systemfinal concentration2×GoldStar Probe Mixture25µl1×Forward Primer, 10µM1µl0.2µM¹⁾Reverse Primer, 10µM1µl0.2µM¹⁾Probe, 10µM1µl0.2µM²⁾Template DNA2µl³⁾ 50xLow ROX or High ROX(optional)⁴⁾1µl1×ddH₂OUp to 50µlNote: 1) Usually, the primer concentration of 0.2µM can get better results, and 0.1-1.0µM can be used as a reference for setting the range. 2) The concentration of the probe used is related to the fluorescent quantitative PCR instrument used, the type of probe, and the type of fluorescent labeling substance, so please refer to the instruction manual of the instrument or the specific requirements of the use of each fluorescent probe for the adjustment of the concentration during the actual use.(3) Usually the amount of DNA template is 10-100ng genomic DNA or 1-10ng cDNA as a reference. Since the templates of different species contain different copy numbers of target genes, the templates can be subjected to gradient dilution to determine the optimal amount of template to be used.(4) The excitation optical system varies from instrument to instrument, choose to add 50×Low ROX or 50×High ROX according to the instrument using fluorescence quantification.2.PCR reaction programCaution! The pre-denaturation reaction of this product must be completed at 95°C for 10 minutes!Two-step PCR::Note: 1) The hot start enzyme used in this product must be activated under the condition of pre-denaturation 95℃, 10min. 2) It is recommended to use two-step PCR reaction program, if you can't get good experimental results due to the use of primers with lower Tm value, etc., you can try to carry out a three-step PCR amplification, and the annealing temperature should be set in the range of 56℃-64℃ as a reference... Read More | Inquire | Inquire | Protein Purity≥85% by SDS PAGEExtinction CoeffA280 nm = 10.16 at 1.0 mg/ml for pure C3Molecular Weight187,000 Da (2 chains)General DescriptionRat C3 is purified from pooled normal rat serum. C3 is central to the activation of all three pathways of complement activation (Law, S.K.A. and Reid, KProtein Purity≥85% by SDS PAGEExtinction CoeffA280 nm = 10.16 at 1.0 mg/ml for pure C3Molecular Weight187,000 Da (2 chains)General DescriptionRat C3 is purified from pooled normal rat serum. C3 is central to the activation of all three pathways of complement activation (Law, S.K.A. and Reid, K.B.M. (1995)). Initiation of each pathway generates proteolytic enzyme complexes (C3 convertases) which are bound to the target surface. These enzymes cleave a peptide bond in C3 releasing the anaphylatoxin C3a and activating C3b. For a brief time (~60 µs) this nascent C3b is capable of reacting with and covalently coupling to hydroxyl groups on the target surface. Carbohydrates are the favored target, but protein hydroxyls and amino groups also react. This process of tagging the target surface with C3b is called opsonization. The reactive site in nascent C3b is a thioester (Tack B.J., et al. (1980); Pangburn M.K. and MüllerEberhard H.J. (1980)) and C3b is linked to the target through a covalent ester bond (an amide bond is formed if C3b is attached to amino groups). Most of the C3 activated during complement activation never attaches to the surface because its thioester reacts with water forming fluid phase C3b which is rapidly inactivated by factors H and I forming iC3b. Surface-bound C3b is necessary in all three pathways for efficient activation of C5 and formation of C5b-9 complexes that lyse the target cell membrane. Surface-bound C3b and its breakdown products iC3b and C3d are recognized by numerous receptors on lymphoid and phagocytic cells which use the C3b ligand to stimulate antigen presentation to cells of the adaptive immune system. The end result is an expansion of target-specific B-cell and T-cell populations.Physical Characteristics & StructureThe calculated molecular weight of rat C3 based on its amino acid sequence is 184,111daltons (without the signal peptide) and is similar to that of human C3 (185,000 daltons).The molecular weight of rat C3 as determined by SDS/polyacrylamide gel electrophoresis has been reported by Daha, M.R. et al., (1979) to be 187,000 daltons composed of two disulfide linked chains, alpha chain (123,000 daltons) and beta chain (76,000 daltons). The extinction coefficient of rat C3 (E1%/280nm = 10.16) is calculated based on its amino acid sequence using ProtParam and assumes all pairs of Cys residues form cystines (i.e. a pair of cysteine molecules are joined by a disulfide bond). The theoretical pI of rat C3 is 6.12. The normal plasma concentration of C3 inWistar rats has been reported to be 0.581mg/ml (Daha, M.R. et al., (1979)).FunctionThe biological functions of C3 are described above in the General Description section.GeneticsRat C3 chromosome location 9. The NCBI Gene ID number for rat C3 is 24232 and UniProt accession number is P01026.Precautions/Toxicity/HazardsThis protein is purified from animal plasma/serum and therefore precautions appropriate for handling any animal blood-derived product must be used.ReferencesLaw, S.K.A. and Reid, K.B.M. (1995) Complement 2nd Edition (ISBN 0199633568) Oxford University Press, Oxford.Tack BF, Harrison RA, Janatova J, Thomas ML, Prahl JW. (1980) Evidence for presence of an internal thiolester bond in third component of human complement. Proc Natl Acad Sci U S A. 77:5764-8.Pangburn M.K. and Müller-Eberhard H.J. (1980) Relation of putative thioester bond in C3 to activation of the alternative pathway and the binding of C3b to biological targets of complement. J Exp Med. 152:1102-14.Daha MR, Stuffers-Heiman M, Kijlstra A and Van ES LA. (1979) Isolation and characterization of the third component of rat complement. Immunology 36:63-70... Read More | Ganglioside GT1b is a brain ganglioside. It is composed of a neutral tetra-saccharide core, with one or two sialic acid on the internal galactose and an extra sialic acid on the non-reducing terminal of galactose |