| Description | Inquire | Inquire | GoldStar Probe Mixture is a premixed system specifically designed for real-time fluorescence quantitative PCR using probe methods (TaqMan, Molecular Beacon, etc.), with a concentration of 2 x, containing GoldStar Taq DNA Polymerase, PCR Buffer, dNTPs, and Mg2+. The operation is simple and convenientGoldStar Probe Mixture is a premixed system specifically designed for real-time fluorescence quantitative PCR using probe methods (TaqMan, Molecular Beacon, etc.), with a concentration of 2 x, containing GoldStar Taq DNA Polymerase, PCR Buffer, dNTPs, and Mg2+. The operation is simple and convenient. Mainly used for detecting genomic DNA target sequences and RNA reverse transcription cDNA target sequences, such as gene expression analysis, copy number analysis, SNP genotype analysis, etc., suitable for fluorescence quantification using different types of probe methods. The GoldStar Taq DNA Polymerase contained in this product is a chemically modified, novel and highly efficient hot start enzyme. It has no polymerase activity at room temperature, effectively avoiding non-specific amplification caused by non-specific binding of primers and templates or primer dimerization at room temperature. The enzyme activation requires incubation at 95 ℃ for 10 minutes. The unique combination of PCR buffer system and hot start enzyme significantly improves the amplification efficiency of PCR, with stronger fluorescence signal and higher sensitivity, which can detect single copy templates. By using this product, a wider linear range can be obtained, resulting in more accurate quantification of the target gene. Suitable for all fluorescence quantitative PCR instruments that do not require ROX as a calibration dye.ROX dye is used to correct the fluorescence signal error between wells in quantitative PCR instruments, and is generally used in Real Time PCR amplification instruments from companies such as ABI and Stratagene. The excitation optical systems of different instruments vary, so the concentration of ROX dye must be matched with the corresponding fluorescence quantitative PCR instrument.Instruments that do not require ROX calibration (CW0932): Roche LightCycle 480, Roche LightCyler 96, Bio rad iCyler iQ, iQ5, CFX96, etc.Instrument requiring Low ROX calibration (CW2625): ABI Prism7500/7500 Fast, QuantStudio ® 3 System, QuantStudio ® 5 System, QuantStudio ® 6 Flex System, QuantStudio ® 7 Flex System, ViiA 7 System, Stratagene Mx3000/Mx3005P, Corbett Rotor Gene 3000, etc.Instruments that require High ROX calibration (CW2626): ABI Prism7000/7300/7700/7900, Eppendorf, ABI Step One/Step One Plus, etc.G665832Component5 mLStorageG665832A2×GoldStar Probe Mixture5×1 mL-20℃. Avoid freeze/thaw cycle.G665832BddH2O5×1 mL -20℃. Avoid freeze/thaw cycle. Notes:1. Before use, please gently mix upside down to avoid foaming, and use after briefly centrifugation.2. Avoid repeated freezing and thawing of this product, as repeated freezing and thawing may cause a decrease in product performance. This product can be stored for a long time at -20 ℃, away from light. If frequent use is required in the short term, it can be stored at 2-8 ℃.Usage:The following are examples of conventional PCR reaction systems and reaction conditions. In practical operation, corresponding improvements and optimizations should be made based on different templates, primer structures, and target fragment sizes.1. PCR reaction system Reagent 50 µl Reaction system Final concentration 2×GoldStar Probe Mixture 25 µl 1 × Forward Primer，10 µM 1 µl 0.2 µM¹⁾ Reverse Primer，10 µM 1 µl 0.2 µM¹⁾ Probe，10 µM 1 µl 0.2 µM²⁾ Template DNA 2 µl³⁾ / 50×Low ROX or High ROX（optional）⁴⁾ 1 µl 1 × ddH2O up to 50 µl / Attention:1) Typically, the primer concentration is 0.2 µ M can achieve good results, ranging from 0.1 to 1.0 µ M serves as a reference for setting the range.2) The concentration of the probe used is related to the fluorescent quantitative PCR instrument used, the type of probe, and the type of fluorescent labeling substance. Please refer to the instrument manual or the specific usage requirements of each fluorescent probe for concentration adjustment during actual use.3) The amount of DNA template is usually based on 10-100 ng genomic DNA or 1-10 ng cDNA as a reference. Due to the different copy numbers of target genes contained in templates of different species, gradient dilution can be applied to the template to determine the optimal template usage.4) The excitation optical systems of different instruments vary, and depending on the instrument used for fluorescence quantification, 50 x Low ROX or 50 x High ROX can be added.2. PCR reaction programAttention! The pre denaturation reaction of this product must be completed at 95 ℃ for 10 minutes!Two step PCR Step Temperature Time / Pre denaturation 95℃ 10 min¹⁾ / Denaturation 95℃ 15 s 35-40 cycles Annealing/Extension ²⁾ 60℃ 1 min 35-40 cycles Attention:1) The hot start enzyme used in this product must be activated under pre denaturation conditions of 95 ℃ and 10 minutes.2) It is recommended to use a two-step PCR reaction program. If good experimental results cannot be obtained due to the use of primers with lower Tm values, a three-step PCR amplification can be attempted. The annealing temperature should be set within the range of 56 ℃ -64 ℃ as a reference... Read More | Reverse transcriptases are enzymes encoded in retroviruses viral genome. The enzyme is responsible for transcription of the viral RNA to produce a dsDNA that can be inserted into the host genome.Reverse transcriptases are multifunctional enzymes. These enzymes exhibit an RNA and DNA directed Reverse transcriptases are enzymes encoded in retroviruses viral genome. The enzyme is responsible for transcription of the viral RNA to produce a dsDNA that can be inserted into the host genome.Reverse transcriptases are multifunctional enzymes. These enzymes exhibit an RNA and DNA directed polymerase activity. In addition reverse transcriptases catalyze the degradation of RNA in an RNA-DNA hybrid. The exonucleolytic activity proceeds in a 5' ---> 3' direction. The RNA or DNA directed activity requires a template (RNA or DNA) and a primer. The following is a schematic illustration of the reaction:Unit definition: One unit incorporates 1 nanomole of tritiated dTMP into acid insoluble productsusing poly(A)•oligo(dT) 12-18 as the template-primer in 20 minutes at 37° C.ApplicationsHIV reverse transcriptase is used for research on the AIDS primer. However it can be substituted for AMV reverse transcriptase, which is mainly used to transcribe mRNA into double stranded cDNA, that can be inserted into prokaryotic vectors. The enzyme can also be used with either single stranded DNA or RNA templates to make probes for use in hybridization experiments. It can be used for labeling the termini of DNA fragments with protruding 5' termini. The enzyme can also be used to sequence DNAs by the dideoxy chain termination method of Sanger when the Klenow fragment of E. coli DNA polymerase I, or the T7 DNA polymerase yield unsatisfactory results.Reagents0.05 M Tris, pH 8.3, containing 0.008 M MgCl21 mg/ml polyadenylic acid in water (poly A)DNA primer:Oligo d(T)12-181 µ mole dTTP/mL stock solution[methyl-3H]-Thymidine 5'-triphosphate (3H-dTTP)dTTP-3H-dTTP working mix: Add 1-2 µL 3H-dTTP per mL of 100 nmol/mL dTTP in order to obtain 1 to 1.5 x 105 cpm/mL1% bovine serum albumin10% perchloric acid1% perchloric acidBuffer substrate reaction mixture: Prepare fresh, immediately before use:For each 1mL of reaction mixture required mix:0.7 mL Tris/HCl, pH 8.3, 0.008M MgCl20.3 mL 1 mg/mL poly(A) RNA template0.005 mL 0.02 mg/mL oligo d(T)12-18 DNA primer0.02mL 1% BSAEnzymedilute as needed wtih 0.05M Tris/HCl, pH 8.3, 0.008M MgCl2 containing 0.1 mg/mL (1%) BSAProcedurePipette into each tube as follows:Buffer substrate mix：0.1 mLdTTP-3H3-dTTP：0.1 mLEnzyme：5-10 µLIncubate 20 minutes at 37° C. Stop reaction by adding 1 ml 10% cold perchloric acid. Filter through 0.2µ manifold filters used with Millipore vacuum manifold. Wash four times using 2mL 1% cold perchloric acid/wash. Transfer filter to scintillation vials. Add 2mL Cellosolve (or 2-methoxyethanol) to dissolve filter. Filters become opaque upon addition of Cellosolve. Make sure filters are dissolved before proceeding. Add 10mL scintillation cocktail and count.Calculation... Read More | Format:1-ComponentEnzyme:Horseradish peroxidase |