| Description | Product descriptionCompositionStorage Conditions50T100TSolution ARoom temperature100mL200mLDetox BRoom temperature25g50gAfter the product is received, store the ingredients at the temperature indicated above, and it will be valid for 12 months. Ethidium bromide (EB) Ames test results show that EB Product descriptionCompositionStorage Conditions50T100TSolution ARoom temperature100mL200mLDetox BRoom temperature25g50gAfter the product is received, store the ingredients at the temperature indicated above, and it will be valid for 12 months. Ethidium bromide (EB) Ames test results show that EB can easily cause mutations in organisms. Powerful EB Detoxifier is a product specially designed to remove ethidium bromide (EB) pollution. It can effectively destroy the structure of EB and remove the carcinogenicity of EB, thereby achieving the purpose of cleaning EB pollution. It is suitable for removing EB contamination of electrophoresis buffer, biochemical solution and solid surface (such as laboratory bench, centrifuge, glassware, stainless steel products, etc.). After using a powerful EB detoxifier to treat EB pollutants, then discarding it can protect the environment from EB pollutants.Product performance indexIt can destroy the structure of EB, eliminate the fluorescence of EB, and reduce its mutagenicity by more than 99.5%.Precautions1. Solution A is corrosive, and to protect your safety during the operation of EB, please wear gloves and goggles.2. There may be a small amount of irritating and harmful gas generated during the chemical reagent preparation and processing of EB, please operate in a fume hood.3. There is no method that can eliminate EB 100%, so even after handling, you should wear gloves and handle it carefully, not as 100% safe. If conditions permit, it is best to regularly test for mutagenicity to ensure the correctness of the treatment process.Operation steps: (Please read the notes before experiment)1. Treatment of various pollution solutions (100mL EB pollution solution)1) Ensure that the concentration of EB in various polluted solutions does not exceed 0.5mg/mL. If the concentration is too high, first dilute with water to meet the required concentration.2) Preparation of working solution: In a fume hood, dilute 2 mL of solution A with deionized water to a final volume of 20 mL for use. Dissolve 0.42 g of detoxifier B in water and dilute to 12 mL for use.3) Add the above 20mL solution A working solution and 12mL detoxifier B working solution to 100mL EB contaminated solution, stir and mix carefully (make sure pH≤3).4) Allow to react at room temperature for 24 hours, adjust the pH to 5-9 with sodium bicarbonate.5) Wash the reactants into the water tank with a lot of water for disposal.2. Various solid surface pollution treatment1) Preparation of working solution: In a fume hood, add 4.2g of detoxifier B to 300mL of deionized water, add 20mL of solution A after fully dissolving, stir and mix carefully (pH is about 1.8).2) After ensuring that the electrical appliances are in a power-off state, soak the freshly prepared working fluid with a paper towel, carefully wipe clean the contaminated surface, repeat 6 times, each time change to a new paper towel soaked in the working fluid, and finally soak it clean Wipe clean the working fluid with paper towels of deionized water, and collect the paper towels into a designated processing container. The pH value of the working fluid is 1.8, which is slightly corrosive. It is not suitable for wiping items with weak tolerance. You can use paper towels soaked in deionized water to wipe. Before wiping, a UV lamp can be used to help find the contaminated area. After wiping, it can help confirm that it has been wiped clean.3) Soak these contaminated paper towels in the working fluid at room temperature for at least one hour. After adjusting the pH to 5-9 with sodium bicarbonate, the liquid is flushed into the sink with plenty of water, and the paper towels are put into the garbage dump... Read More | Inquire | Seals and prevents freezing of stopcocks and ground-glass joints in high-vacuum systems at pressures less than 10-6 mm Hg. Heat stable (?40 to 260 °C), low vapor pressure, and chemically resistant. Colorless. 5.3 oz. tube | Purity: >90%, by SDS-PAGE visualized with Coomassie® Blue Staining.Description：CNN1 is a member of the calponin family. CNN1 is a thin filament-associated protein which is involved in the regulation and modulation of smooth muscle contraction. CNN1 is able to bind to actin, calmodulinPurity: >90%, by SDS-PAGE visualized with Coomassie® Blue Staining.Description：CNN1 is a member of the calponin family. CNN1 is a thin filament-associated protein which is involved in the regulation and modulation of smooth muscle contraction. CNN1 is able to bind to actin, calmodulin, troponin C and tropomyosin. Prevention of actomyosin Mg-ATPase activity is a result of interaction between calponin and actin... Read More | Purity> 97 % by SDS-PAGE and HPLC analyses.FunctionReceptor for TNFSF2/TNF-alpha and homotrimeric TNFSF1/lymphotoxin-alpha. The adapter molecule FADD recruits caspase-8 to the activated receptor. The resulting death-inducing signaling complex (DISC) performs caspase-8 proteolytic activation whichPurity> 97 % by SDS-PAGE and HPLC analyses.FunctionReceptor for TNFSF2/TNF-alpha and homotrimeric TNFSF1/lymphotoxin-alpha. The adapter molecule FADD recruits caspase-8 to the activated receptor. The resulting death-inducing signaling complex (DISC) performs caspase-8 proteolytic activation which initiates the subsequent cascade of caspases (aspartate-specific cysteine proteases) mediating apoptosis. Contributes to the induction of non-cytocidal TNF effects including anti-viral state and activation of the acid sphingomyelinase... Read More |