| Description | Inquire | 2x Taq MasterMix is a premixed system composed of Taq DNA Polymerase, Mg2+, dNTPs, PCR stabilizers, and enhancers. The pre prepared PCR mixture makes the operation simpler and faster, and can minimize human error and contamination to the greatest extent possible. The original MasterMix formula 2x Taq MasterMix is a premixed system composed of Taq DNA Polymerase, Mg2+, dNTPs, PCR stabilizers, and enhancers. The pre prepared PCR mixture makes the operation simpler and faster, and can minimize human error and contamination to the greatest extent possible. The original MasterMix formula results in high yield, strong repeatability, and good stability of amplified products. This product does not contain dyes. After the PCR program is completed, an appropriate amount of sample buffer can be added as needed for electrophoresis operation. The amplified PCR product has an "A" base attached to the 3 'end, making it suitable for direct use in T/A cloning. Mainly suitable for PCR amplification of DNA, DNA sequencing and other experiments.Quality control: T665627Component5mlStorageT665627A2×Taq MasterMix5×1ml-20℃. Avoid freeze/thaw cycle.T665627BddH₂O5×1ml-20℃. Avoid freeze/thaw cycle.Notes: 2×Taq MasterMix contains Taq DNA Polymerase, 3mM MgCl2 and 400µM each dNTP After testing, there was no exogenous nuclease activity; PCR method for detecting residual DNA without host; Can effectively amplify single copy genes from multiple genomes.Usage:The following is an example of a PCR reaction system and reaction conditions for amplifying a 1 kb fragment using human genomic DNA as a template. In practical operation, corresponding improvements and optimizations should be made based on the template, primer structure, and target fragment size.1. PCR reaction systemReagent50 µlReaction systemFinal concentration2×Taq MasterMix25 µl1×Forward Primer，10 µM2 µl0.4 µMReverse Primer，10 µM2 µl0.4 µMTemplate DNA<0.5 µg<0.5 µg/50 µlddH2Oup to 50 µl/Attention: The primer concentration should be between 0.1 and 1.0 as the final concentration µ M serves as a reference for setting the range. In the case of low amplification efficiency, the concentration of primers can be increased; When non-specific reactions occur, the primer concentration can be reduced to optimize the reaction system.2. PCR reaction conditionsStepTemperatureTime/Pre denaturation95℃2 min/Denaturation94℃30 s25-35 cyclesAnneal55-65℃30 s25-35 cyclesExtend72℃30 s25-35 cyclesFinally extended72℃2 min/Attention:1) In general experiments, if the annealing temperature is 5 ℃ lower than the melting temperature Tm of the amplification primer, and the ideal amplification efficiency cannot be achieved, the annealing temperature should be appropriately reduced; When non-specific reactions occur, increase the annealing temperature to optimize the reaction conditions.2) The extension time should be set according to the size of the amplified fragment. The amplification efficiency of Taq DNA Polymerase in this product is 2 kb/min.3) The number of cycles can be set based on the downstream application of the amplification product. If the number of cycles is too small, the amplification amount is insufficient; If there are too many cycles, the probability of mismatches will increase, and non-specific backgrounds will be severe. So, while ensuring product yield, the number of cycles should be minimized as much as possible... Read More | Inquire | Product introduction：Used to isolate lymphocytes from human organsMatters needing attention：1. samples, reagents and experimental environment in the whole process shall be carried out at 20 ± 2 ℃. In order to obtain the best experimental results, it is best to carry out the Product introduction：Used to isolate lymphocytes from human organsMatters needing attention：1. samples, reagents and experimental environment in the whole process shall be carried out at 20 ± 2 ℃. In order to obtain the best experimental results, it is best to carry out the experiment within 2 h of sampling. The longer the sample is stored, the worse the cell separation effect is. The separation effect is even worse after the sample is placed for more than 6 h, or even cannot achieve the purpose of separation. 2. in this experiment, it is better not to use plastic products with high polymerization materials (such as polystyrene), but use non-static, low static ionization heart tubes and glass products without alkali treatment, because the electrostatic effect will lead to cell adhesion, and the surface of alkali treated glass will become rough, which will affect the effect of cell separation. 3. aspirating too many lymphocyte layers and separation liquid layers will cause the granulocytes at the junction of separation liquid to be aspirated, thus increasing the number of mixed granulocytes. 4. when the amount of separating solution is greater than that of tissue single cell suspension sample, the separation effect is better.Scope of application：Lymphocyte isolation... Read More | Inquire |