| Description | Aladdin's 12% SDS-PAGE Resolving Gel Master Mix contains almost all reagents required for the preparation of 12% SDS-PAGE resolving gels, except for polymerization catalysts such as ammonium persulfate and TEMED.Aladdin's SDS-PAGE Resolving Gel Master Mix series can be used to prepare 5 common Aladdin's 12% SDS-PAGE Resolving Gel Master Mix contains almost all reagents required for the preparation of 12% SDS-PAGE resolving gels, except for polymerization catalysts such as ammonium persulfate and TEMED.Aladdin's SDS-PAGE Resolving Gel Master Mix series can be used to prepare 5 common concentrations of gelsPrecautions：Ammonium Persulfate or its substitute (, ST005) and TEMED are required but not provided in this product.This product contains Acr-Bis which is potentially neurotoxic. Please take effective measures to avoid direct contact with the human body or inhalation.This product is for R&D only. Not for drug, household, or other uses.For your safety and health, please wear a lab coat and disposable gloves during the operation.Instructions for Use：1.According to the size of a target protein, decide an appropriate concentration of SDS-PAGE resolving gel. Please refer to the table below.SDS-PAGE Resolving Gel Concentration Optimal Separation Range6%50-150kD8%30-90kD10 -80kD12%12-60kD15%10-40kD2.Prepare a 10% ammonium persulfate solution with ddH2O or other high-purity water. Solution of ammonium persulfate or its substitute is prone to failure and should be prepared freshly or kept frozen for multiple uses.3.Prepare the resolving gel according to the table below. For example, add 100µl of 10% ammonium persulfate and 4µl of TEMED into 10ml of 12% SDS-PAGE Resolving Gel Master Mix, mix well, and immediately pour into gel cassette. Overlay with the top layer of water-saturated butanol, isopropanol, 0.1% SDS or distilled water. Leave at room temperature (~25℃) until fully solidified (usually within 10-30 minutes). Note: The amount of polymerization catalyst in the table below is recommended for polymerization at 25℃. It can be adjusted appropriately according to the temperature. For example, when the room temperature is lower than 20℃, add more TEMED and 10% ammonium persulfate appropriately to promote gel solidification.ReagentsVolume of each component (ml) required for different volumes of SDS-PAGE resolving gel12% SDS-PAGE Resolving Gel Master Mix5101520305010% ammonium persulfate or its substitute0.050.10.150.20.30.5TEMED 0.0020.0040.0060.0080.0120.024.After complete polymerization of the resolving gel, remove the liquid used for sealing, and then prepare the SDS-PAGE stacking gel with 's SDS-PAGE Stacking Gel Master Mix. 5.If the prepared gel is not to be used on the same day, it can be stored at 4℃ for 1-2 days... Read More | Inquire | Purity:>95%, by SDS-PAGE visualized with Coomassie® Blue Staining. Description： 100B, previously called S100 beta, belongs to the S100 family within the EF-hand superfamily of Ca2+ binding proteins. S100 proteins contain two EF-hand motifs that differ in affinity, separated by a hingePurity:>95%, by SDS-PAGE visualized with Coomassie® Blue Staining. Description： 100B, previously called S100 beta, belongs to the S100 family within the EF-hand superfamily of Ca2+ binding proteins. S100 proteins contain two EF-hand motifs that differ in affinity, separated by a hinge region with a hydrophobic cleft that is exposed upon Ca2+ binding. S100B is a 91 amino acid (aa) protein, after removal of the initial methionine, and is found as homodimers of 10.4 kDa monomers. Human S100B shares 99%, 98%, 100%, 99% and 97% aa sequence identity with mouse, rat, rabbit, equine and bovine S100B, respectively. Within the S100 family, human S100B shows the highest aa identity (59%) with S100A1. S100B is expressed primarily by astrocytes and oligodendrocytes in the central nervous system, and by Schwann cells in the peripheral nervous system. Ca2+-bound S100B interacts in vitro with at least 20 cytoplasmic proteins, including several structural molecules such as tubulin and GFAP. It can inhibit the phosphorylation of these kinase substrates and others such as tau and neuromodulin. Astrocytes can secrete S100B, which then acts in a cytokine-like manner. Nanomolar concentrations of S100B are secreted constitutively, promote proliferation, and are neurotrophic and anti-apoptotic. Blood levels of S100B reflect extracellular concentrations within the nervous system, and are elevated in Down’s syndrome, Alzheimer’s disease and Tourette’s syndrome, metabolic stress, acute brain injury and brain tumors. Micromolar concentrations of S100B can be destructive and pro-apoptotic; they induce the expression of iNOS, COX-2, IL-1, IL‑6 and TNF-alpha by microglia, astrocytes or neurons. Most extracellular actions of S100B can be mediated by RAGE (receptor for advanced glycation end products), which is also a receptor for other S100 proteins... Read More | BackgroundStreptavidin is a tetrameric bacterial protein isolated from Streptomyces avidinii providing 4 high-affinity biotin binding sites. Streptavidin homo-tetramers have an extraordinarily high affinity for biotin. With a dissociation constant on the order of ≈10⁻¹⁴ mol/L,BackgroundStreptavidin is a tetrameric bacterial protein isolated from Streptomyces avidinii providing 4 high-affinity biotin binding sites. Streptavidin homo-tetramers have an extraordinarily high affinity for biotin. With a dissociation constant on the order of ≈10⁻¹⁴ mol/L, the binding of biotin to streptavidin is one of the strongest non-covalent interactions known in nature. Unlike egg-white avidin, which has a net positive charge at neutral pH and contains about 7% carbohydrate, streptavidin has almost no net charge at neutral pH, does not contain carbohydrate, and exhibits lower non-specific background. Streptavidin conjugates are widely used together with a conjugate of biotin for specific detection of a variety of proteins, protein motifs, nucleic acids and other molecules. This FITC-streptavidin conjugate was prepared by highly purified Streptavidin and free FITC was removed. Streptavidin (FITC) is a useful second-step reagent for the indirect immunofluorescent staining of cells in combination with biotinylated primary antibodies for flow cytometric analysis. Excitation at 488nm light leads to a fluorescence emission maximum of 520 nm.Recommended Usage：Every lot of Streptavidin-FITC is tested by flow cytometry using biotinylated primary antibodies. From this testing it is recommended that between 0.02 and 0.25 µg of streptavidin be used per 106 cells in a 100 µl staining volume... Read More | This reagent kit is based on TRIzon's improved columnar total RNA extraction kit. This product can be extracted from animal groupsExtract total RNA from samples such as textiles, plant materials, various microorganisms, and cultured cells. Firstly, the cracking solution is fully cracked This reagent kit is based on TRIzon's improved columnar total RNA extraction kit. This product can be extracted from animal groupsExtract total RNA from samples such as textiles, plant materials, various microorganisms, and cultured cells. Firstly, the cracking solution is fully cracked andHomogenized samples, in their unique high salt state, RNA specifically binds to silicon matrix membranes, greatly reducingEffectively removing organic solvent contamination while removing protein contamination, resulting in higher purity and quality of RNA. bookThe product can quickly extract total RNA from various cells or tissues, and can process 30-50 mg of tissue or 5 × 10 ⁶ cells each time,Can handle multiple different samples simultaneously. If it is an RNA experiment that is very sensitive to trace amounts of DNA, the residual DNA can be utilizedUsing DNase without RNase for digestion and removal on the column, the extracted RNA can be directly applied to RT-PCR Experiments such as Northern Blot, Dot Blot, and in vitro translation. U665516 Component 50 T Storage U665516A DNase I 1000 U -20℃. Avoid freeze/thaw cycle. U665516B 10×Reaction Buffer 1000 µL -20℃. Avoid freeze/thaw cycle. U665516C TRIzon Reagent 60 mL 2-8℃. Protect from light. U665516D TRIzon PaI™ 10 mL 2-8℃. Protect from light. U665516E Buffer RW1 40 mL RT U665516F Buffer RW2 (concentrate) 11 mL RT U665516G RNase-Free Water 10 mL RT U665516H Spin Columns RM with Collection Tubes 50 sets RT U665516I RNase-Free Centrifuge Tubes (1.5 mL) 50 EA RTPreparation and important precautions before the experiment:1.To prevent RNase pollution, attention should be paid to the following aspects:1) RNase's plastic products and gun heads to avoid cross contamination.2) Prepare the solution using water without RNase.3) Operators should wear disposable masks and gloves, and change gloves frequently during the experiment.2. The sample should avoid repeated freezing and thawing, otherwise it will affect the yield and quality of RNA extraction.3. If TRIzon Reagent is found to have precipitates before use, it can be dissolved in a water bath at 56 ℃ for a few minutes.Before the first use, anhydrous ethanol should be added to Buffer RW2 according to the instructions on the reagent bottle label.5. All centrifugation steps should be carried out at room temperature unless otherwise specified, and all operation steps should be carried out quickly.Usage：1. Sample processing1a. Organization: 30-50 mg of tissue is thoroughly ground in liquid nitrogen and 1 mL of TRIzon Reagent is added, or 1 mL of TRIzon Reagent is added to the tissue sample and homogenized. Attention: The sample volume should not exceed 10% of the volume of TRIzon Reagent.2a. Single layer cell culture: Remove the culture medium and add an appropriate amount every 10 cm ² Add 1 mL of TRIzon Reagent.3a. Cell suspension: Collect cells by centrifugation. Add 1 mL of TRIzon Reagent to every 5 × 10 µ m cell.2. After adding TRIzon Reagent, repeatedly blow a few times to fully crack the sample. Leave at room temperature for 5 minutes to completely separate the protein nucleic acid complex.3. Add 200 to every 1 mL of TRIzon Reagent µ LTRIzon PaI ™， Cover the tube tightly, vigorously shake for 15 seconds, and let it sit at room temperature for 2 minutes.4. Centrifuge at 4 ℃ 12000 rpm (~13400 × g) for 10 minutes. At this time, the sample is divided into three layers: the red organic phase, the middle layer, and the upper colorless aqueous phase. RNA is mainly in the upper aqueous phase. Move the upper aqueous phase to a new RNase Free centrifuge tube (provided).5. Add an equal volume of 70% ethanol (prepared without RNase water) to the obtained aqueous solution, invert and mix well.6. Add all the solutions obtained in the previous step to the spin columns RM that have been loaded into the collection tube. If the solution cannot be added at once, it can be transferred in multiple batches. Centrifuge at 12000 rpm for 20 seconds, discard the waste liquid in the collection tube, and place the adsorption column back into the collection tube.7. Add 350 to the adsorption column µ L Buffer RW1, centrifuge at 12000 rpm for 20 seconds, discard the waste liquid in the collection tube, and place the adsorption column back into the collection tube.8. Preparation of DNase I mixture: Take 52 µ LRNase Free Water, add 8 to it µ L 10 x Reaction Buffer and 20 µ L DNase I (1 U/ µ L) Mix well and prepare to a final volume of 80 µ The reaction solution of L.9. Directly add 80 µ L DNase I mixture to the adsorption column and incubate at 20-30 ℃ for 15 minutes.10. Add 350 to the adsorption column µ L Buffer RW1, centrifuge at 12000 rpm for 1 minute, discard the waste liquid, and place the adsorption column back into the recovery manifold.11. Add 500 to the adsorption column µ L Buffer RW2 (check if anhydrous ethanol has been added before use), centrifuge at 12000 rpm for 20 seconds, discard the waste liquid in the collection tube, and place the adsorption column back into the collection tube.12. Repeat step 11.Centrifuge at 12000 rpm for 2 minutes and discard the waste liquid from the collection tube. Place the adsorption column at room temperature for a few minutes and thoroughly air dry. Attention: The purpose of this step is to remove residual ethanol from the adsorption column, which will affect subsequent enzymatic reactions (enzyme digestion,. )PCR, etc.14. Place the adsorption column in a new RNase free centrifuge tube and add 30-50 to the middle of the adsorption column µ Place RNase Free Water at room temperature for 1 minute, centrifuge at 12000 rpm for 1 minute, collect RNA solution, and store RNA at -70 ℃ to prevent degradation.Attention:1) The volume of RNase Free Water should not be less than 30 µ L. Small volume affects the recovery rate.2) If you want to increase RNA production, you can use 30-50 µ Repeat step 14 for the new RNase Free Water.3) If you want to increase the RNA concentration, you can add the obtained solution back to the adsorption column and repeat step 14... Read More |