| Description | Aladdin's 8% SDS-PAGE Resolving Gel Master Mix contains almost all reagents required for the preparation of 8% SDS-PAGE resolving gels, except for polymerization catalysts such as ammonium persulfate and TEMED.Aladdin's SDS-PAGE Resolving Gel Master Mix series can be used to prepare 5 common Aladdin's 8% SDS-PAGE Resolving Gel Master Mix contains almost all reagents required for the preparation of 8% SDS-PAGE resolving gels, except for polymerization catalysts such as ammonium persulfate and TEMED.Aladdin's SDS-PAGE Resolving Gel Master Mix series can be used to prepare 5 common concentrations of gelsPrecautions：Ammonium Persulfate or its substitute (, ST005) and TEMED are required but not provided in this product.This product contains Acr-Bis which is potentially neurotoxic. Please take effective measures to avoid direct contact with the human body or inhalation.This product is for R&D only. Not for drug, household, or other uses.For your safety and health, please wear a lab coat and disposable gloves during the operation.Instructions for Use：1.According to the size of a target protein, decide an appropriate concentration of SDS-PAGE resolving gel. Please refer to the table below.SDS-PAGE Resolving Gel Concentration Optimal Separation Range6%50-150kD8%30-90kD10 -80kD12%12-60kD15%10-40kD2.Prepare a 10% ammonium persulfate solution with ddH2O or other high-purity water. Solution of ammonium persulfate or its substitute is prone to failure and should be prepared freshly or kept frozen for multiple uses.3.Prepare the resolving gel according to the table below. For example, add 100µl of 10% ammonium persulfate and 4µl of TEMED into 10ml of 8% SDS-PAGE Resolving Gel Master Mix, mix well, and immediately pour into gel cassette. Overlay with the top layer of water-saturated butanol, isopropanol, 0.1% SDS or distilled water. Leave at room temperature (~25℃) until fully solidified (usually within 10-30 minutes). Note: The amount of polymerization catalyst in the table below is recommended for polymerization at 25℃. It can be adjusted appropriately according to the temperature. For example, when the room temperature is lower than 20℃, add more TEMED and 10% ammonium persulfate appropriately to promote gel solidification. ReagentsVolume of each component (ml) required for different volumes of SDS-PAGE resolving gel8% SDS-PAGE Resolving Gel Master Mix5101520305010% ammonium persulfate or its substitute0.050.10.150.20.30.5TEMED 0.0020.0040.0060.0080.0120.024.After complete polymerization of the resolving gel, remove the liquid used for sealing, and then prepare the SDS-PAGE stacking gel with 's SDS-PAGE Stacking Gel Master Mix. 5.If the prepared gel is not to be used on the same day, it can be stored at 4℃ for 1-2 days... Read More | Inquire | Inquire | Inquire | Product Characteristics UNI-StabilPLUS is a universal stabilizer for the dilution and stabilization of both Horseradish Peroxidase (HRP) and Alkaline Phosphatase (AP) labeled proteins and antibodies, in order to maintain the molecular conformation and prevent loss of activity over time. This enablesProduct Characteristics UNI-StabilPLUS is a universal stabilizer for the dilution and stabilization of both Horseradish Peroxidase (HRP) and Alkaline Phosphatase (AP) labeled proteins and antibodies, in order to maintain the molecular conformation and prevent loss of activity over time. This enables the making of pre-diluted, ready-to-use conjugates, minimizing assay errors in dilution. Superior stabilization of HRP and AP conjugated antibodies in low as well as high protein dilutions is seen, when using UNI-StabilPLUS. When tested with AP conjugated antibody stability is seen as follows: • at least 3 years at 2-8 °C • at least 2 years at room temperature • at least 4 weeks at 37 °C When tested with HRP conjugated antibody stability is seen as follows: • at least 2 years at 2-8 °C • at least 1 years at room temperature • at least 2 weeks at 37 °CUNI-StabilPLUS is recommended for the dilution of antibodies directed against rabbit immunoglobulins unlike HRP-StabilPLUS (cat. no. H494387) and Antibody Enhancer (cat. no. A494276).Composition & Properties UNI-StabilPLUS is a ready-to use buffer that appears as an opaque solution. The product is based on a mild acid Tris buffer containing proprietary stabilizing components. UNI-StabilPLUS contains neither BSA, nor other material from bovine serum, no azide, mercury or other toxic components.Working Procedure 1.Make a series of dilutions of the HRP- or AP conjugated protein in UNI-StabilPLUS in order to determine the optimal dilution. 2.Run the assay as usual or store the diluted conjugated protein preferably at 2-8 °C.Tips & Tricks • Avoid using phosphate buffers for AP-conjugated antibody assays. We recommend the use of Tris/HCl, Tween as the washing buffer, instead of a PBS buffer which will reduce signal significantly. • For extended stability of HRP conjugated antibodies, HRP-StabilPLUS (cat. no. H494387) is recommended. Handling & Storage • Store solution at 2-8 °C... Read More |