| Description | DFFA Human Pre-designed siRNA Set A contains three designed siRNAs for DFFA gene (Human), as well as a negative control, a positive control, and a FAM-labeled negative control. Components DFFA siRNA-1: 5 nmol (HPLC) DFFA siRNA-2: 5 nmol (HPLC) DFFA siRNA-3: 5 nmol (HPLC) siRNA Negative Control: 5 DFFA Human Pre-designed siRNA Set A contains three designed siRNAs for DFFA gene (Human), as well as a negative control, a positive control, and a FAM-labeled negative control. Components DFFA siRNA-1: 5 nmol (HPLC) DFFA siRNA-2: 5 nmol (HPLC) DFFA siRNA-3: 5 nmol (HPLC) siRNA Negative Control: 5 nmol (HPLC) FAM-labeled siRNA Negative Control: 5 nmol (HPLC) GAPDH siRNA Positive Control:5 nmol (HPLC)... Read More | Protein Purity≥85% by SDS PAGEExtinction CoeffA280 nm = 0.631 at 1.0 mg/ml for pure C1qMolecular Weight400,000 Da (18 chains)General DescriptionRat C1q is purified from pooled normal rat serum. C1q is part of the C1 complex, which is the first complement component in the classical pathway of Protein Purity≥85% by SDS PAGEExtinction CoeffA280 nm = 0.631 at 1.0 mg/ml for pure C1qMolecular Weight400,000 Da (18 chains)General DescriptionRat C1q is purified from pooled normal rat serum. C1q is part of the C1 complex, which is the first complement component in the classical pathway of complement. The C1 complex is a non-covalent assembly of three different proteins (C1q, C1r, and C1s) bound together in a calcium-dependent complex. C1q has six extended arms with domains at the end of each arm that bind to the Fc domains of immunoglobulins such as IgG or IgM. When antibodies bind toantigens, forming immune complexes, they cluster allowing two or more of the six C1q arms to bind to the Fc domains of antibodies. Rat IgG2 is very efficient when compared to IgG1 in activating complement (Medgyesi, G.A et., al., 1981). This is in contrast to the human system in which IgG1 activates complement but not IgG2 (Redpath, S. et. al., 1998). The binding of multiple arms of C1q to immune complexes causes the two C1r proteins in the complex (protease zymogens) to auto-activate. The activated C1r proteases cleave and activate the two C1s protease zymogens in the complex. The activated C1s cleaves complement component C4 releasing C4a and initiating covalent attachment of C4b to the activating surface. Activated C1s also cleaves C2 and the larger fragment of C2 binds to the surface-attached C4b forming C4b,C2a, the C3/C5 convertase of the classical pathway.Rat IgG1 cannot activate complement whereas rat IgG2 does.Physical Characteristics & StructureThe apparent molecular weight of rat C1q as determined by gel filtration has been reported to be 400,000 by Veerhuis, R. et al., (1985) and is calculated to be 420,000 based on its amino acid sequence. Rat C1q is a high molecular weight complex of 18 polypeptide chains. Each of the six arms of rat C1q contains three chains, an A chain (~30,000 daltons), a B chain (~28,000 daltons) and a C chain (~26,000 daltons) as determined by SDS/polyacrylamide gel electrophoresis (Wing, M.G. et al., (1993)).FunctionThe biological functions of C1q are described above in the General Description and Physical Characteristics sections.ApplicationsRat C1q can be used to coat ELISA plates to capture and quantitate immune complexes in samples from rat models used for studying immune complex related diseases and conditions.GeneticsNCBI Gene ID numbers for rat C1q are: C1q A chain (298566), C1q B chain (29687), and C1q C chain (362634). The genes for C1q chains A, B and C are all located on chromosome 5. The UniprotKB primary accession numbers for rat C1q are: C1q A chain (P31720), C1q B chain (P31721), and C1q C chain (P31722).Precautions/Toxicity/HazardsThis protein is purified from animal plasma/serum and therefore precautions appropriate for handling any animal blood-derived product must be used.ReferencesMedgyesi, G.A et., Miklos, K., Kulics, J., Fust, G., and Gergely, J. Bazin, H. (1981). Classes and subclasses of rat antibodies: reaction with the antigen and interaction of the complex with the complement system. Immunology 43, 171-176.Redpath, S., Michaelsen, T., Sandlie, I. and Clark, M. R. (1998). Activation of complement by human IgG1 and human IgG3 antibodies against the human leucocyte antigen CD52. Immunology 93, 595–600.Veerhuis, R., Van Es, L.A. and Daha, M.R. (1985). In vivo degradation of rat C1q induced by intravenous injection of soluble IgG aggregates. Immunology 54, 801-810.Wing, M.G., Seilly, D. J., Bridgman, D.J. and Harrison, R.A. (1993). Rapid isolation and biochemical characterization of rat C1 and C1q. Molecular Immunology 30, 433-440... Read More | 1、Product attributeShelf life: 24 monthsReaction time：long (up to 45 minutes) at 20-37°CLot-to-lot variation：<10%Boiling point : 100℃pH-Value (at 20 °C): 9.0-9.8 Density (20℃) : 1.0302 g/cm³Water solubility: easily solubleAppearance: colourless to 1、Product attributeShelf life: 24 monthsReaction time：long (up to 45 minutes) at 20-37°CLot-to-lot variation：<10%Boiling point : 100℃pH-Value (at 20 °C): 9.0-9.8 Density (20℃) : 1.0302 g/cm³Water solubility: easily solubleAppearance: colourless to light yellow liquidOdour: odourlessIncubation temperature: 20-37 °CLight sensitiveHeat sensitive 2、Requirements for storage rooms and vessels1.Keep container tightly closed.2.Keep cool. protected from light3. Do not store together with: Oxidizing agent. 4. Contaminated or leaked out substrate solution from damaged bottles should not be used anymore and has to be destroyed.5. Use isolated containers with some cool bags for transport.6. Spontaneous decay will increase the background. If stored at room temperature, the velocity of the decay will increase. Thus, both storage and transport at room temperature should be avoided. Nevertheless, the activity of the solution is not affected by storage at room temperature. The solution still works beyond the expiry date, but some applications, especially those including visual evaluation, may be hampered by increased background. 3、Effective Components and Principle of FunctionIn different buffer solutions (pH = 9.5), with supplementation if required, the effective componentpara nitrophenyl phosphate (pNPP) is dissolved. Alkaline Phosphatase transfers the phosphate residue to an acceptor. Under alkaline conditions a yellow colour occurs, resulting from the formed nitrophenol. 4、Biosafety informationThis mixture is not classified as hazardous in accordance with Regulation (EC) No 1272/2008； 5、Advantage1. Signal yield comparable to competitor ready-to-use solutions2. Broad measurement range3. Very low background signals4. Very low blank drift during long-term storage (<0.15 AU within 24 months)5. High colour stability after reaction stop with this product and other commonly used stopping solutions 6、Instruction for usageFor bottling consider the following instructions:• Work in a dust free and darkened room.• Keep the solution as cool as possible.• Avoid contact of the solutions with any metal parts• Clean all instruments and vessels very extensively.• Wear powder-free gloves during bottling.• Close the bottles immediately to minimize the influence of light and dust.• Use clean bottles that are impermeable to light made from HDPE or PP. 7、 General Instructions for the Use in Blotting Systems Only qualified laboratory staff, who are familiar with the basics of immunological methods, are allowed to use these solutions.The substrate solutions can be used in qualitative and quantitative ELISA procedures.When using 96-well microtiter plates, adding 100 µL of substrate per well after incubation and washing is recommended. After substrate incubation the reaction can be stopped and the photometric measurement can be carried out. Using higher incubation temperatures (37° C) may shorten the incubation time. The reaction can be stopped by using the special developed solution stop. The use of other commercially available stop solutions cannot safely exclude a further increase of the signal. Addition of a stopping solution does not change the general shape of the spectrum. The unstopped and the stopped solution should be measured at 405 nm and the background correction: should be measured at 620 nm... Read More | Extinction CoeffA280 nm = 1.0 at 1.0 mg/mlGeneral DescriptionProduct is whole polyclonal antiserum from goats immunized with highly purified mouse complement protein. This product is not a purified IgG fraction. Goats are maintained in FDA certified facilities.Physical Characteristics & Extinction CoeffA280 nm = 1.0 at 1.0 mg/mlGeneral DescriptionProduct is whole polyclonal antiserum from goats immunized with highly purified mouse complement protein. This product is not a purified IgG fraction. Goats are maintained in FDA certified facilities.Physical Characteristics & StructureAntibodies present in the antisera are primarily IgG.ApplicationsImmunodiffusion: Effective against NMS and plasma at 1/32 dilution Suggested starting dilutions:Western Blot: 1/500 to 1/1000. Most effective against non-reduced antigen.ELISA: 1/500 to 1/2000... Read More | GoldStar Probe Mixture is a premixed system specifically designed for real-time fluorescence quantitative PCR using probe methods (TaqMan, Molecular Beacon, etc.), with a concentration of 2 x, containing GoldStar Taq DNA Polymerase, PCR Buffer, dNTPs, and Mg2+. The operation is simple and convenientGoldStar Probe Mixture is a premixed system specifically designed for real-time fluorescence quantitative PCR using probe methods (TaqMan, Molecular Beacon, etc.), with a concentration of 2 x, containing GoldStar Taq DNA Polymerase, PCR Buffer, dNTPs, and Mg2+. The operation is simple and convenient. Mainly used for detecting genomic DNA target sequences and RNA reverse transcription cDNA target sequences, such as gene expression analysis, copy number analysis, SNP genotype analysis, etc., suitable for fluorescence quantification using different types of probe methods. The GoldStar Taq DNA Polymerase contained in this product is a chemically modified, novel and highly efficient hot start enzyme. It has no polymerase activity at room temperature, effectively avoiding non-specific amplification caused by non-specific binding of primers and templates or primer dimerization at room temperature. The enzyme activation requires incubation at 95 ℃ for 10 minutes. The unique combination of PCR buffer system and hot start enzyme significantly improves the amplification efficiency of PCR, with stronger fluorescence signal and higher sensitivity, which can detect single copy templates. By using this product, a wider linear range can be obtained, resulting in more accurate quantification of the target gene. Suitable for all fluorescence quantitative PCR instruments that do not require ROX as a calibration dye.ROX dye is used to correct the fluorescence signal error between wells in quantitative PCR instruments, and is generally used in Real Time PCR amplification instruments from companies such as ABI and Stratagene. The excitation optical systems of different instruments vary, so the concentration of ROX dye must be matched with the corresponding fluorescence quantitative PCR instrument.Instruments that do not require ROX calibration (CW0932): Roche LightCycle 480, Roche LightCyler 96, Bio rad iCyler iQ, iQ5, CFX96, etc.Instrument requiring Low ROX calibration (CW2625): ABI Prism7500/7500 Fast, QuantStudio ® 3 System, QuantStudio ® 5 System, QuantStudio ® 6 Flex System, QuantStudio ® 7 Flex System, ViiA 7 System, Stratagene Mx3000/Mx3005P, Corbett Rotor Gene 3000, etc.Instruments that require High ROX calibration (CW2626): ABI Prism7000/7300/7700/7900, Eppendorf, ABI Step One/Step One Plus, etc.G665832Component5 mLStorageG665832A2×GoldStar Probe Mixture5×1 mL-20℃. Avoid freeze/thaw cycle.G665832BddH2O5×1 mL -20℃. Avoid freeze/thaw cycle. Notes:1. Before use, please gently mix upside down to avoid foaming, and use after briefly centrifugation.2. Avoid repeated freezing and thawing of this product, as repeated freezing and thawing may cause a decrease in product performance. This product can be stored for a long time at -20 ℃, away from light. If frequent use is required in the short term, it can be stored at 2-8 ℃.Usage:The following are examples of conventional PCR reaction systems and reaction conditions. In practical operation, corresponding improvements and optimizations should be made based on different templates, primer structures, and target fragment sizes.1. PCR reaction system Reagent 50 µl Reaction system Final concentration 2×GoldStar Probe Mixture 25 µl 1 × Forward Primer，10 µM 1 µl 0.2 µM¹⁾ Reverse Primer，10 µM 1 µl 0.2 µM¹⁾ Probe，10 µM 1 µl 0.2 µM²⁾ Template DNA 2 µl³⁾ / 50×Low ROX or High ROX（optional）⁴⁾ 1 µl 1 × ddH2O up to 50 µl / Attention:1) Typically, the primer concentration is 0.2 µ M can achieve good results, ranging from 0.1 to 1.0 µ M serves as a reference for setting the range.2) The concentration of the probe used is related to the fluorescent quantitative PCR instrument used, the type of probe, and the type of fluorescent labeling substance. Please refer to the instrument manual or the specific usage requirements of each fluorescent probe for concentration adjustment during actual use.3) The amount of DNA template is usually based on 10-100 ng genomic DNA or 1-10 ng cDNA as a reference. Due to the different copy numbers of target genes contained in templates of different species, gradient dilution can be applied to the template to determine the optimal template usage.4) The excitation optical systems of different instruments vary, and depending on the instrument used for fluorescence quantification, 50 x Low ROX or 50 x High ROX can be added.2. PCR reaction programAttention! The pre denaturation reaction of this product must be completed at 95 ℃ for 10 minutes!Two step PCR Step Temperature Time / Pre denaturation 95℃ 10 min¹⁾ / Denaturation 95℃ 15 s 35-40 cycles Annealing/Extension ²⁾ 60℃ 1 min 35-40 cycles Attention:1) The hot start enzyme used in this product must be activated under pre denaturation conditions of 95 ℃ and 10 minutes.2) It is recommended to use a two-step PCR reaction program. If good experimental results cannot be obtained due to the use of primers with lower Tm values, a three-step PCR amplification can be attempted. The annealing temperature should be set within the range of 56 ℃ -64 ℃ as a reference... Read More |