| Description | B3GALT2 Human Pre-designed siRNA Set A contains three designed siRNAs for B3GALT2 gene (Human), as well as a negative control, a positive control, and a FAM-labeled negative control. Components B3GALT2 siRNA-1: 5 nmol (HPLC) B3GALT2 siRNA-2: 5 nmol (HPLC) B3GALT2 siRNA-3: 5 nmol (HPLC) siRNA B3GALT2 Human Pre-designed siRNA Set A contains three designed siRNAs for B3GALT2 gene (Human), as well as a negative control, a positive control, and a FAM-labeled negative control. Components B3GALT2 siRNA-1: 5 nmol (HPLC) B3GALT2 siRNA-2: 5 nmol (HPLC) B3GALT2 siRNA-3: 5 nmol (HPLC) siRNA Negative Control: 5 nmol (HPLC) FAM-labeled siRNA Negative Control: 5 nmol (HPLC) GAPDH siRNA Positive Control:5 nmol (HPLC)... Read More | General DescriptionNatural human C5a is prepared from human C5 protein cleaved into C5a and C5b by human C5 convertase. The C5a is converted to C5a desArg by proteolytic removal of the C-terminal arginine. The primary carboxypeptidase responsible for Arg removal is serum carboxypeptidase N, but General DescriptionNatural human C5a is prepared from human C5 protein cleaved into C5a and C5b by human C5 convertase. The C5a is converted to C5a desArg by proteolytic removal of the C-terminal arginine. The primary carboxypeptidase responsible for Arg removal is serum carboxypeptidase N, but there are several different carboxypepticases in serum. C5a desArg is a naturally glycosylated polypeptide containing 73 amino acids with a molecular weight of approx. 10,250 daltons. It contains 25% carbohydrate attached to a single Asn residue at position 64. This carbohydrate is of variable structure leading to a broad distribution of MW upon analysis by mass spectroscopy. C5a is the most potent anaplylatoxin (compared to C3a and C4a). C5a desArg is produced when C5a is“inactivated” by removal of its C-terminal arginine amino acid. This cleavage occurs by the action of the plasma enzyme carboxypeptidase N. This inactivation is rapid and most C5a is converted to C5a desArg within minutes of its formation. “Inactivated” C5a still possesses approx. 1% of its anaphylatoxic and chemotatic activities, but its stimulatory activity is only reduced 10-fold. Thus, C5a desArg retains considerable biological activity even though it is frequently called inactivated C5a. Its biological properties include being weakly chemotactic for neutrophils (PMN), causing smooth muscle contraction, increasing vascular permeability, causing histamine and TNF-alpha release, and causing lysosomal degranulation of immune cells. C5a and C5a desArg act through the C5a Receptor (C5aR, CD88, a G-protein coupled receptor) on PMN, monocytes, alveolar macrophages, and mast cells. A second receptor of unknown function (C5L2, gpr77) has been identified. Due to the widespread expression of C5a receptors and the results from C5aR KO mice it is believed that C5a and its receptors have many nonimmunolgical functions in organ development, CNS development, neurodegeneration, tissue regeneration and hematopoiesis (Monk, P.N. et al. (2007)).Native versus Recombinant C5a desArgNumerous recombinant forms of C5a and C5a desArg are sold by many companies. In side-by-side biological testing, we have found that our native native proteins are 10- to 100-fold more active per µg than all but one of these recombinant proteins. Structurally not a single one of the recombinant proteins on the market has the correct amino acid sequence or structure. They have extra amino acids at the N-terminal (such as 6 His tags), different amino acids in the sequence itself (some were produced from the original, but incorrect amino acid sequence), and none possess the 25% carbohydrate at Asn 64. In fact, one recombinant C5a on the market has approximately 30 additional amino acids at the N-terminal end due to the cloning vector used. This is a 40% addition of nonsense structure to the C5a molecule. Both our C5a and our C5adesArg are native proteins produced by the native human C5 convertase.Physical Characteristics & StructureDeglycosylated MW: Calculated monoisotopic mass 8112; Calculated average mass 8117.Isoelectric point: pI = 8.8Carbohydrate content: ~25% carbohydrate (heterogeneous) Amino acid sequence: TLQKKIEEIA AKYKHSVVKK CCYDGACVNN DETCEQRAAR ISLGPRCIKA FTECCVVASQ LRANISHKDM QLGMDL Number: MFCD00130842NMRderived structure: FEBS Lett. 238:289-294, 1988; Biochemistry 28:172-185,1989; Biochemistry 29:2895-2905, 1990; Proteins 28:261-267, 1997.Extinction Coeff. A280 nm = 0.41 at 1.0 mg/mlPurity: > 97% by SDS-PAGEAssaysThe multitude of biological functions of C5a has resulted in the use of many different assay systems. The most typical biological assays being smooth muscle contraction assays using guinea pig ileum, chemotaxis assays using neutrophils or granule-release assays using human PMN or similar cell lines. Granule release is generally followed by measuring the release of myeloperoxidase. Functional responses have been detected in the picomolar concentration range (Gerard, C. et al. (1981); Hugli, T.E. et al. (1981)).ELISA kits for the assay of C5a and C5a desArg in blood and other fluids are sold by many companies. These measurements are useful for detecting complement activation in vivo, but the interpretation of their meaning is complicated by the fact that clearance of the anaphylatoxins is rapid.In vivoThe resting serum concentration of C5a desArg has been reported to be approximately 4 nM although it is difficult to draw, store and test blood without 1 to 10 % C5 activation (Watkins, J. (1987)). The presence of EDTA and Futhan in the collection tubes can minimize this background. Full activation of all C5 in blood (75 µg/mL) would result in ~380 nM C5a (~3.9 µg/mL). Due to the extreme sensitivity of many C5a responses, a response can theoretically be initiated by activation of approximately one millionth of the C5 in a local area (sub-picomolar C5a).RegulationC5adesArg levels are regulated by two processes: formation and clearance. The enzymes that cleave C5 and release C5a (collectively called C5 convertases) do so at very slow rates. Operating at Vmax the best enzymes only cleave one C5 every three minutes (Rawal, N. and Pangburn, M.K. (2001)). C5a desArg is created when C5a is“inactivated” by removal of its C-terminal arginine amino acid. The product C5a desArg is produced by the action of the plasma enzyme carboxypeptidase N. This inactivation is rapid and most C5a is converted to C5a desArg within minutes of its formation. “Inactivated” C5a still possesses approx. 1% of its anaphylatoxic and chemotatic activities, but its stimulatory activity is only reduced 10-fold. Thus, C5a desArg retains considerable biological activity even though it is frequently called inactivated C5a. Because of the large number of cells bearing C5a receptors (endothelial, immune, smooth muscle, neuronal, etc.) the capture, internalization and digestion of C5a and C5a desArg results in their rapid removal from circulation.DeficienciesA deficiency of C5 or a deficiency of the enzymes that cleave C5 to generate C5a would result in the absence of C5a and C5a desArg. A knock-out mouse deficient in carboxypeptidase N has been created and found to be hypersensitive to complement activation and CVF administration (Mueller-Ortiz S.L. et al. (2009)). Administration of human C5a was 100% lethal in these KO mice probably due to their inability to inactivate C5a to C5a desArg. There are no known complete deficiencies of C5 convertases. Examples of C5 deficient humans and mice exist. In fact, many laboratory mouse strains in common use were shown to have been bred with a deficiency of C5 (A/HeJ, AKR/J, DBA/2J, NZB/B1NJ, SWR/J, and B10.D2/nSnJ). The lack of C5 prevents formation of the membrane attack complex of complement and precludes formation of C5a and C5a desArg. Humans lacking C5 are susceptible to repeated infections from a wide variety of organisms, primarily gram-negative bacteria. Meningococcal and gonococcal neisserial infections are especially problematic. The degree to which pathologies associated with C5 deficiency are due to the lack of C5 or due to the absence of C5a and C5a desArg is unclear but information on this isbeing acquired from receptor knock-out animals.DiseasesSee Deficiencies above.Precautions/Toxicity/HazardsThis protein is purified from human serum and therefore precautions appropriate for handling any blood-derived product must be used even though the source was shown by certified tests to be negative for HBsAg, HTLV-I/II, STS, and for antibodies to HCV, HIV-1 and HIV-II.Injection can cause anaphylatic shock which is a generalized circulatory collapse similar to that caused by an allergic reaction.Hazard Code: B WGK Germany 3MSDS available upon request... Read More | Product contentF665774Component5 mLStorageF665774A2×Fast Probe Mixture5×1 mL-20℃. Avoid freeze/thaw cycle.F665774B50×High ROX200 µL-20℃. Avoid freeze/thaw cycle.F665774CddH2O5×1 mL-20℃. Avoid freeze/thaw cycle.Product IntroductionFast Probe Mixture is a preProduct contentF665774Component5 mLStorageF665774A2×Fast Probe Mixture5×1 mL-20℃. Avoid freeze/thaw cycle.F665774B50×High ROX200 µL-20℃. Avoid freeze/thaw cycle.F665774CddH2O5×1 mL-20℃. Avoid freeze/thaw cycle.Product IntroductionFast Probe Mixture is a pre-mixed system for real-time fluorescence PCR by probe method (TaqMan, Molecular Beacon, etc.), with a concentration of 2×, including Fast Taq DNA Polymerase, PCR Buffer, dNTPs, Mg2+ and so on, which is easy and convenient to operate. It is mainly used for the detection of genomic DNA target sequence and cDNA target sequence after RNA reverse transcription. The Fast Taq DNA Polymerase contained in this product can effectively reduce the non-specific amplification generated by the non-specific binding of primers and templates or primer dimerization at room temperature, and the activation of the enzyme only needs to be incubated at 95 ℃ for 30 s. The whole PCR reaction process can save about 40 minutes compared with the ordinary reaction, which greatly shortens the reaction time of PCR. The combination of unique PCR buffer system and fast hot start enzyme effectively inhibits the generation of non-specific products and significantly improves the PCR amplification efficiency with stronger fluorescence signal, higher sensitivity and wider linear range. The product has a wide range of applications and can be used for both normal and rapid quantitative PCR programs.ROX dye is used to correct the fluorescence signal error generated between wells of a quantitative PCR instrument, and is generally used in Real Time PCR amplifiers from ABI, Stratagene, and other companies. The excitation optics vary from instrument to instrument, so the concentration of ROX dye must be matched to the corresponding fluorescence quantitative PCR instrument.Instruments that do not require ROX calibration (F665766):Roche LightCycler 480, Roche LightCyler 96, Bio-rad iCyler iQ, iQ5, CFX96 and others.Instruments that require Low ROX calibration (F665768):ABI Prism7500/7500 Fast, QuantStudio®3 System, QuantStudio®5 System, QuantStudio®6 Flex System, QuantStudio®7 Flex System, ViiA 7 system. Stratagene Mx3000/Mx3005P, Corbett Rotor Gene 3000, and more.Instruments that require High ROX calibration (F665774):ABI Prism 7000/7300/7700/7900, Eppendorf, ABI Step One/Step One Plus, and others.matters needing attention1. Before use, please mix gently by turning up and down, avoid foaming as much as possible, and use after brief centrifugation.2. Avoid repeated freezing and thawing of this product, repeated freezing and thawing may degrade the product performance. This product can be stored for long term at -20℃, protected from light. If frequent use is required within a short period of time, it can be stored at 2-8℃.UsageThe following examples are conventional PCR reaction systems and reaction conditions, which should be improved and optimized according to the template, primer structure and target fragment size in actual operation.1.PCR reaction systemreagents50µl reaction systemfinal concentration2×Fast Probe Mixture25 µl1×Forward Primer, 10µM1µl0.2µM¹⁾Reverse Primer, 10µM1µl0.2µM¹⁾Probe, 10 µM1µl0.2µM²⁾Template DNA2µl³⁾ 50x Low ROX or High ROX(optional)⁴⁾1µl1×ddH₂Oup to 50µlNote: 1) Usually the primer concentration of 0.2µM can get better results, and 0.1-1.0µM can be used as a reference for setting the range. 2) The final concentration of the probe used is related to the fluorescent quantitative PCR instrument used, the type of probe, and the type of fluorescent labeling substance, so please refer to the instruction manual of the instrument or the specific requirements of the use of each fluorescent probe for the adjustment of the concentration in actual use.(3) Usually the amount of DNA template is 10-100ng genomic DNA or 1-10ng cDNA as a reference. Since the templates of different species contain different copy numbers of target genes, the templates can be subjected to gradient dilution to determine the optimal amount of template to be used.(4) The excitation optical system varies from instrument to instrument, choose to add 50×Low ROX or 50×High ROX according to the instrument using fluorescence quantification.2. PCR reaction program:A two-step PCR reaction program is recommended, and this program is set up using the ABI 7500 Fluorescent Quantitative PCR Instrument as a reference.Note: 1) The enzyme used in this product must be pre-denatured at 95°C for 30s to achieve enzyme activation. Under this condition, most of the templates can be well unchained. For templates with high GC content and complex secondary structure, the pre-denaturation time can be extended to 1-4 minutes to allow the starting template to fully unchain.(2) It is recommended to use two-step PCR reaction program, if you do not get good experimental results due to the use of primers with lower Tm values, etc., you can try to carry out three-step PCR amplification, and the annealing temperature, please use the range of 56 ℃ - 64 ℃ as a setting reference... Read More | Inquire | Products contentN665730Component24 T96 TStorageN665730ATPS V50 144 µL576 µL-20℃. Avoid freeze/thaw cycle.N665730B5×FA Reaction Buffer144 µL576 µL-20℃. Avoid freeze/thaw cycle.N665730C2×HiFidelity PCR Mix600 µL2×1.2 mL-20℃. Avoid freeze/thaw Products contentN665730Component24 T96 TStorageN665730ATPS V50 144 µL576 µL-20℃. Avoid freeze/thaw cycle.N665730B5×FA Reaction Buffer144 µL576 µL-20℃. Avoid freeze/thaw cycle.N665730C2×HiFidelity PCR Mix600 µL2×1.2 mL-20℃. Avoid freeze/thaw cycle.N665730DPPM48 µL192 µL-20℃. Avoid freeze/thaw cycle.* This kit is suitable for human genomic DNA library construction with a starting template DNA input of 50 ng. We also have transposase library construction kits for human genomic DNA starting at 5 ng and 1 ng, so it is recommended to use different kits for different starting amounts of DNA in order to obtain higher quality libraries. Products IntroductionThis kit is developed for Illumina's high-throughput sequencing platform and provides the enzyme premix system and reaction buffer for genomic DNA library construction, including all components except PCR primers. Compared with the traditional library construction kits, this kit adopts the new transposase method for library construction, which can complete DNA fragmentation, end repair and junction reaction in one simple enzymatic reaction, significantly reducing the amount of template, reducing the number of experimental steps, and shortening the time of library construction; it adopts the high-fidelity DNA polymerase for library enrichment, and the preference-free PCR amplification can expand the coverage area of the sequence, which can be used for efficient and effective sequencing. The use of high-fidelity DNA polymerase for library enrichment and preference-free PCR amplification broadens the coverage area of the sequence and enables efficient preparation of DNA libraries for Illumina's second-generation sequencing platform. The kit is suitable for DNA libraries with a starting template of 50 ng, and all reagents in the kit have been subjected to strict quality control and functional validation to maximize the stability and reproducibility of library construction. Product Features ● DNA fragmentation and junction ligation in one step.● Ultra-fidelity amplification minimizes amplification-preferred steps.Provide your own instruments, kits and consumables1. Magnetic frame: DynaMagTM-2 is recommended.2. DNA purification and recovery kit: It is recommended to use DNA purification and recovery kit by magnetic bead method.3. Library PCR primer kits: transposase method for second-generation sequencing multi-sample primer kits are recommended. 4. Anhydrous ethanol, deionized water (pH between 7.0 and 8.0).5. Reaction tubes: It is recommended to use low adsorption PCR tubes and 1.5 ml centrifuge tubes. Tips: It is recommended to use high quality filter tips to prevent contamination of kits and library samples. Pre-experiment Preparation and Important Notes1. Avoid repeated freezing and thawing of reagents.2. PCR products are easily contaminated due to improper operation, resulting in inaccurate results. It is recommended to isolate the PCR reaction system preparation area from the PCR product purification area, and to use special pipettes to clean the experimental areas at regular intervals.3. Bead purification: the beads should be equilibrated to room temperature before use, all operations on the beads should be carried out at room temperature, 80% ethanol should be dispensed freshly, the beads should be rinsed and dried until the surface is free of liquid reflections and has a frosted appearance, insufficient drying of the beads will cause ethanol residue that will affect the subsequent experiments, and over-drying of the beads will affect the efficiency of DNA recovery.4. The kit is suitable for human genomic DNA library construction, if the DNA sample is a PCR product, it should be ensured that its length>.500 bp, since transposases do not work on DNA ends, it is recommended to extend the PCR product by 50-100 bp at each end of the PCR product to avoid low coverage of the ends for sequencing.Sample PreparationDNA purity requirements: A260/A280 = 1.8-2.0. Sample DNA: dissolve in ultrapure water. DNA Quantification: Too much or too little DNA will affect the quality of the library. It is recommended to use Nano to test the purity of the genomic DNA and then use Qubit to test the concentration of the genome (do not use any absorbance-based assay for template quantification).Schematic diagram of DNA banking processprocedureDNA fragmentation, junction reaction1. Add the following reagents to a 200 µl PCR tube: 2. Mix by gently blowing with a pipette and centrifuge briefly so that all components are collected at the bottom of the tube.3. Place the above PCR tubes in the PCR instrument with the hot cap on and program the reaction as follows:DNA should be purified immediately after the fragmentation reaction has been performed and the transposase is still in a high state of activity.to prevent smaller library fragments due to DNA over-fragmentation. Purification of fragmentation productsWe recommend the use of the Century Magnetic Bead Method DNA Purification and Recovery Kit.1. CMPure should be equilibrated at room temperature for 30 min after shaking and mixing before use.2. Add 50 µl of magnetic beads equilibrated to room temperature to the fragmentation product, vortex and shake for 5 seconds, then let stand at room temperature for 5 minutes.3. Centrifuge briefly, place the tube on a magnetic rack to separate the beads from the supernatant solution until the solution is clear (approximately 3-5 minutes), carefully aspirate the supernatant and discard, avoiding contact with the beads that have bound the target DNA. Note: Do not discard the beads.4. Continue to keep the centrifuge tube fixed on a magnetic rack and add 200 µl of freshly prepared 80% ethanol to the centrifuge tube and allow to stand at room temperature for 30 seconds, carefully discarding the supernatant.Note: When adding ethanol, the liquid must not be blown directly onto the beads.5. Repeat step 4.6. Keep the centrifuge tube fixed on a magnetic rack and leave to dry at room temperature until the surface of the beads is slightly cracked, then add 23 µlddH2O to solubilize.Note: Do not over-dry the beads as this may affect the elution efficiency.7. Remove the tube from the magnetic rack, vortex to completely resuspend the beads, and allow to stand at room temperature for 5 minutes. Centrifuge briefly, place the tube on the magnetic rack until the solution is clear, and transfer 21 µl of supernatant to a new 200 µl PCR tube.PCR amplification Add the following reagents to the 200 µl PCR tube: Mix by gently blowing with a pipette and centrifuge briefly so that all components are collected at the bottom of the tube.3. Place the above PCR tubes in the PCR instrument with the hot cap on and program the reaction as follows:Selective recovery of library DNA fragmentsIt is recommended to use CombiVision Magnetic Beads DNA Purification and Recovery Kit for selective recovery of DNA fragments. When different sizes of DNA fragments are required, the amount of magnetic beads to be used is different, please refer to the attached table for the specific amount of magnetic beads to be used (if other brands of magnetic beads are used, you need to find out the optimal amount of magnetic beads to be used on your own).Note: Amplification products can also be fragment length sorted and purified using the Gum Recovery Kit. If there is no special requirement for library length distribution, the amplification products can also be purified without selective recovery of DNA fragments as described on page 6 of the manual.1. CMPure should be equilibrated at room temperature for 30 min after shaking and mixing before use.2. Transfer the PCR product to a 1.5 ml centrifuge tube, rehydrate to 100 µl and add several volumes of magnetic beads equilibrated to room temperature, vortex for 5 seconds and let stand at room temperature for 5 minutes.3. Centrifuge briefly, place the tube on a magnetic rack to separate the beads from the supernatant until the solution is clear, and carefully aspirate the supernatant and transfer it to a new 1.5 ml centrifuge tube.Note: Do not discard the top clear.4. Add several volumes of magnetic beads to the supernatant, vortex and shake for 5 seconds, then let stand at room temperature for 5 minutes.5. Centrifuge briefly, place the tube on a magnetic rack to separate the beads from the supernatant until the solution is clear, carefully aspirate the supernatant and discard it, avoiding contact with the beads that have bound the target DNA.Note: Do not discard the beads.6. Continue to keep the centrifuge tube fixed on a magnetic rack and add 200 µl of freshly prepared 80% ethanol to the tube and allow to stand at room temperature for 30 seconds, carefully discarding the supernatant.Note: When adding ethanol, the liquid must not be blown directly onto the beads.7. Repeat step 6 once.8. Keep the centrifuge tube fixed on a magnetic rack and leave to dry at room temperature until the surface of the beads is slightly cracked, add 20 µl of ddH2O to solubilize.Note: Do not over-dry the beads as this may affect the elution efficiency.9. Remove the centrifuge tube from the magnetic rack, vortex and oscillate to completely resuspend the beads, and let stand at room temperature for 5 minutes. Leave brieflycentrifuge, place the tube on a magnetic rack until the solution is clear, and transfer the supernatant solution to a new centrifuge tube. Table: Suggested amount of magnetic beads for different segment selection recoveryLibrary DNA fragment purificationWe recommend the use of the Century Magnetic Bead Method DNA Purification and Recovery Kit.1. CMPure should be equilibrated at room temperature for 30 min after shaking and mixing before use.2. 50 µl of magnetic beads equilibrated to room temperature were added to the PCR product, vortexed and shaken for 5 seconds, and then left to stand at room temperature for 5 minutes.3. Centrifuge briefly, place the tube on a magnetic rack to separate the beads from the supernatant solution until the solution is clear (approximately 3-5 minutes), carefully aspirate the supernatant and discard it, avoiding contact with the beads that have bound the target DNA. Note: Do not discard the beads.4. Continue to keep the centrifuge tube fixed on a magnetic rack and add 200 µl of freshly prepared 80% ethanol to the centrifuge tube and allow to stand at room temperature for 30 seconds, carefully discarding the supernatant.Note: When adding ethanol, the liquid must not be blown directly onto the beads.5. Repeat step 4.6. Keep the centrifuge tube fixed on a magnetic rack and leave to dry at room temperature until the surface of the beads is slightly cracked, add 25 µl of ddH2O to solubilize.Note: Do not over-dry the beads as this may affect the elution efficiency.7. Remove the tube from the magnetic rack, vortex to completely resuspend the beads, and allow to stand at room temperature for 5 minutes. Centrifuge briefly, place the tube on the magnetic rack until the solution is clear, and transfer the supernatant solution to a new tube.Library quality controlDetermination of library concentrationIn order to obtain high-quality sequencing results, accurate quantification of DNA libraries is required, and the first recommendation is to use Real-timePCR methods are used for absolute quantification of DNA libraries. Additionally, fluorescent dye methods such as the Qubit method or the fluorescent dye picogreen method can be used; do not use quantification methods based on absorbance measurements here. The following approximate formula can be used to convert the molar concentration of the DNA library. Average total length of librariesApproximate conversion formula Library fragment distributionThe prepared DNA libraries can be detected by agarose gel electrophoresis or Agilent 2100 Bioanalyzer.Range of segment length distributions... Read More |