| Description | CHRNA2 Human Pre-designed siRNA Set A contains three designed siRNAs for CHRNA2 gene (Human), as well as a negative control, a positive control, and a FAM-labeled negative control. Components CHRNA2 siRNA-1: 5 nmol (HPLC) CHRNA2 siRNA-2: 5 nmol (HPLC) CHRNA2 siRNA-3: 5 nmol (HPLC) siRNA Negative CHRNA2 Human Pre-designed siRNA Set A contains three designed siRNAs for CHRNA2 gene (Human), as well as a negative control, a positive control, and a FAM-labeled negative control. Components CHRNA2 siRNA-1: 5 nmol (HPLC) CHRNA2 siRNA-2: 5 nmol (HPLC) CHRNA2 siRNA-3: 5 nmol (HPLC) siRNA Negative Control: 5 nmol (HPLC) FAM-labeled siRNA Negative Control: 5 nmol (HPLC) GAPDH siRNA Positive Control:5 nmol (HPLC)... Read More | Products contentN665730Component24 T96 TStorageN665730ATPS V50 144 µL576 µL-20℃. Avoid freeze/thaw cycle.N665730B5×FA Reaction Buffer144 µL576 µL-20℃. Avoid freeze/thaw cycle.N665730C2×HiFidelity PCR Mix600 µL2×1.2 mL-20℃. Avoid freeze/thaw Products contentN665730Component24 T96 TStorageN665730ATPS V50 144 µL576 µL-20℃. Avoid freeze/thaw cycle.N665730B5×FA Reaction Buffer144 µL576 µL-20℃. Avoid freeze/thaw cycle.N665730C2×HiFidelity PCR Mix600 µL2×1.2 mL-20℃. Avoid freeze/thaw cycle.N665730DPPM48 µL192 µL-20℃. Avoid freeze/thaw cycle.* This kit is suitable for human genomic DNA library construction with a starting template DNA input of 50 ng. We also have transposase library construction kits for human genomic DNA starting at 5 ng and 1 ng, so it is recommended to use different kits for different starting amounts of DNA in order to obtain higher quality libraries. Products IntroductionThis kit is developed for Illumina's high-throughput sequencing platform and provides the enzyme premix system and reaction buffer for genomic DNA library construction, including all components except PCR primers. Compared with the traditional library construction kits, this kit adopts the new transposase method for library construction, which can complete DNA fragmentation, end repair and junction reaction in one simple enzymatic reaction, significantly reducing the amount of template, reducing the number of experimental steps, and shortening the time of library construction; it adopts the high-fidelity DNA polymerase for library enrichment, and the preference-free PCR amplification can expand the coverage area of the sequence, which can be used for efficient and effective sequencing. The use of high-fidelity DNA polymerase for library enrichment and preference-free PCR amplification broadens the coverage area of the sequence and enables efficient preparation of DNA libraries for Illumina's second-generation sequencing platform. The kit is suitable for DNA libraries with a starting template of 50 ng, and all reagents in the kit have been subjected to strict quality control and functional validation to maximize the stability and reproducibility of library construction. Product Features ● DNA fragmentation and junction ligation in one step.● Ultra-fidelity amplification minimizes amplification-preferred steps.Provide your own instruments, kits and consumables1. Magnetic frame: DynaMagTM-2 is recommended.2. DNA purification and recovery kit: It is recommended to use DNA purification and recovery kit by magnetic bead method.3. Library PCR primer kits: transposase method for second-generation sequencing multi-sample primer kits are recommended. 4. Anhydrous ethanol, deionized water (pH between 7.0 and 8.0).5. Reaction tubes: It is recommended to use low adsorption PCR tubes and 1.5 ml centrifuge tubes. Tips: It is recommended to use high quality filter tips to prevent contamination of kits and library samples. Pre-experiment Preparation and Important Notes1. Avoid repeated freezing and thawing of reagents.2. PCR products are easily contaminated due to improper operation, resulting in inaccurate results. It is recommended to isolate the PCR reaction system preparation area from the PCR product purification area, and to use special pipettes to clean the experimental areas at regular intervals.3. Bead purification: the beads should be equilibrated to room temperature before use, all operations on the beads should be carried out at room temperature, 80% ethanol should be dispensed freshly, the beads should be rinsed and dried until the surface is free of liquid reflections and has a frosted appearance, insufficient drying of the beads will cause ethanol residue that will affect the subsequent experiments, and over-drying of the beads will affect the efficiency of DNA recovery.4. The kit is suitable for human genomic DNA library construction, if the DNA sample is a PCR product, it should be ensured that its length>.500 bp, since transposases do not work on DNA ends, it is recommended to extend the PCR product by 50-100 bp at each end of the PCR product to avoid low coverage of the ends for sequencing.Sample PreparationDNA purity requirements: A260/A280 = 1.8-2.0. Sample DNA: dissolve in ultrapure water. DNA Quantification: Too much or too little DNA will affect the quality of the library. It is recommended to use Nano to test the purity of the genomic DNA and then use Qubit to test the concentration of the genome (do not use any absorbance-based assay for template quantification).Schematic diagram of DNA banking processprocedureDNA fragmentation, junction reaction1. Add the following reagents to a 200 µl PCR tube: 2. Mix by gently blowing with a pipette and centrifuge briefly so that all components are collected at the bottom of the tube.3. Place the above PCR tubes in the PCR instrument with the hot cap on and program the reaction as follows:DNA should be purified immediately after the fragmentation reaction has been performed and the transposase is still in a high state of activity.to prevent smaller library fragments due to DNA over-fragmentation. Purification of fragmentation productsWe recommend the use of the Century Magnetic Bead Method DNA Purification and Recovery Kit.1. CMPure should be equilibrated at room temperature for 30 min after shaking and mixing before use.2. Add 50 µl of magnetic beads equilibrated to room temperature to the fragmentation product, vortex and shake for 5 seconds, then let stand at room temperature for 5 minutes.3. Centrifuge briefly, place the tube on a magnetic rack to separate the beads from the supernatant solution until the solution is clear (approximately 3-5 minutes), carefully aspirate the supernatant and discard, avoiding contact with the beads that have bound the target DNA. Note: Do not discard the beads.4. Continue to keep the centrifuge tube fixed on a magnetic rack and add 200 µl of freshly prepared 80% ethanol to the centrifuge tube and allow to stand at room temperature for 30 seconds, carefully discarding the supernatant.Note: When adding ethanol, the liquid must not be blown directly onto the beads.5. Repeat step 4.6. Keep the centrifuge tube fixed on a magnetic rack and leave to dry at room temperature until the surface of the beads is slightly cracked, then add 23 µlddH2O to solubilize.Note: Do not over-dry the beads as this may affect the elution efficiency.7. Remove the tube from the magnetic rack, vortex to completely resuspend the beads, and allow to stand at room temperature for 5 minutes. Centrifuge briefly, place the tube on the magnetic rack until the solution is clear, and transfer 21 µl of supernatant to a new 200 µl PCR tube.PCR amplification Add the following reagents to the 200 µl PCR tube: Mix by gently blowing with a pipette and centrifuge briefly so that all components are collected at the bottom of the tube.3. Place the above PCR tubes in the PCR instrument with the hot cap on and program the reaction as follows:Selective recovery of library DNA fragmentsIt is recommended to use CombiVision Magnetic Beads DNA Purification and Recovery Kit for selective recovery of DNA fragments. When different sizes of DNA fragments are required, the amount of magnetic beads to be used is different, please refer to the attached table for the specific amount of magnetic beads to be used (if other brands of magnetic beads are used, you need to find out the optimal amount of magnetic beads to be used on your own).Note: Amplification products can also be fragment length sorted and purified using the Gum Recovery Kit. If there is no special requirement for library length distribution, the amplification products can also be purified without selective recovery of DNA fragments as described on page 6 of the manual.1. CMPure should be equilibrated at room temperature for 30 min after shaking and mixing before use.2. Transfer the PCR product to a 1.5 ml centrifuge tube, rehydrate to 100 µl and add several volumes of magnetic beads equilibrated to room temperature, vortex for 5 seconds and let stand at room temperature for 5 minutes.3. Centrifuge briefly, place the tube on a magnetic rack to separate the beads from the supernatant until the solution is clear, and carefully aspirate the supernatant and transfer it to a new 1.5 ml centrifuge tube.Note: Do not discard the top clear.4. Add several volumes of magnetic beads to the supernatant, vortex and shake for 5 seconds, then let stand at room temperature for 5 minutes.5. Centrifuge briefly, place the tube on a magnetic rack to separate the beads from the supernatant until the solution is clear, carefully aspirate the supernatant and discard it, avoiding contact with the beads that have bound the target DNA.Note: Do not discard the beads.6. Continue to keep the centrifuge tube fixed on a magnetic rack and add 200 µl of freshly prepared 80% ethanol to the tube and allow to stand at room temperature for 30 seconds, carefully discarding the supernatant.Note: When adding ethanol, the liquid must not be blown directly onto the beads.7. Repeat step 6 once.8. Keep the centrifuge tube fixed on a magnetic rack and leave to dry at room temperature until the surface of the beads is slightly cracked, add 20 µl of ddH2O to solubilize.Note: Do not over-dry the beads as this may affect the elution efficiency.9. Remove the centrifuge tube from the magnetic rack, vortex and oscillate to completely resuspend the beads, and let stand at room temperature for 5 minutes. Leave brieflycentrifuge, place the tube on a magnetic rack until the solution is clear, and transfer the supernatant solution to a new centrifuge tube. Table: Suggested amount of magnetic beads for different segment selection recoveryLibrary DNA fragment purificationWe recommend the use of the Century Magnetic Bead Method DNA Purification and Recovery Kit.1. CMPure should be equilibrated at room temperature for 30 min after shaking and mixing before use.2. 50 µl of magnetic beads equilibrated to room temperature were added to the PCR product, vortexed and shaken for 5 seconds, and then left to stand at room temperature for 5 minutes.3. Centrifuge briefly, place the tube on a magnetic rack to separate the beads from the supernatant solution until the solution is clear (approximately 3-5 minutes), carefully aspirate the supernatant and discard it, avoiding contact with the beads that have bound the target DNA. Note: Do not discard the beads.4. Continue to keep the centrifuge tube fixed on a magnetic rack and add 200 µl of freshly prepared 80% ethanol to the centrifuge tube and allow to stand at room temperature for 30 seconds, carefully discarding the supernatant.Note: When adding ethanol, the liquid must not be blown directly onto the beads.5. Repeat step 4.6. Keep the centrifuge tube fixed on a magnetic rack and leave to dry at room temperature until the surface of the beads is slightly cracked, add 25 µl of ddH2O to solubilize.Note: Do not over-dry the beads as this may affect the elution efficiency.7. Remove the tube from the magnetic rack, vortex to completely resuspend the beads, and allow to stand at room temperature for 5 minutes. Centrifuge briefly, place the tube on the magnetic rack until the solution is clear, and transfer the supernatant solution to a new tube.Library quality controlDetermination of library concentrationIn order to obtain high-quality sequencing results, accurate quantification of DNA libraries is required, and the first recommendation is to use Real-timePCR methods are used for absolute quantification of DNA libraries. Additionally, fluorescent dye methods such as the Qubit method or the fluorescent dye picogreen method can be used; do not use quantification methods based on absorbance measurements here. The following approximate formula can be used to convert the molar concentration of the DNA library. Average total length of librariesApproximate conversion formula Library fragment distributionThe prepared DNA libraries can be detected by agarose gel electrophoresis or Agilent 2100 Bioanalyzer.Range of segment length distributions... Read More | Purity:>90%, by SDS-PAGE visualized with Coomassie® Blue Staining.Description: DCX (doublecortin, N-GST chimera)contains 2 doublecortin domains and belongs to the doublecortin family. It is highly expressed in neuronal cells of fetal brain, but not expressed in other fetal tissues. In the Purity:>90%, by SDS-PAGE visualized with Coomassie® Blue Staining.Description: DCX (doublecortin, N-GST chimera)contains 2 doublecortin domains and belongs to the doublecortin family. It is highly expressed in neuronal cells of fetal brain, but not expressed in other fetal tissues. In the adult, it is highly expressed in the brain frontal lobe, but very low expression in other regions of brain, and not detected in heart, placenta, lung, liver, skeletal muscles, kidney and pancreas. DCX is a microtubule-associated protein required for initial steps of neuronal dispersion and cortex lamination during cerebral cortex development. It may act by competing with the putative neuronal protein kinase DCAMKL1 in binding to a target protein. DCX may in that way participate in a signaling pathway that is crucial for neuronal interaction before and during migration, possibly as part of a calcium ion-dependent signal transduction pathway. It may be part with LIS-1 of a overlapping, but distinct, signaling pathways that promote neuronal migration. Defects in DCX are the cause of lissencephaly X-linked type 1 and subcortical band heterotopia X-linked... Read More | Purity:>90%, by SDS-PAGE visualized with Coomassie® Blue Staining.Description:BIRC5, also known as Survivin and EPR-1, is a member of theIAP family. IAP family members usually contain multiple baculovirus IAP repeat (BIR) domains, but BIRC5 has only a single BIR domain. It is expressed cell Purity:>90%, by SDS-PAGE visualized with Coomassie® Blue Staining.Description:BIRC5, also known as Survivin and EPR-1, is a member of theIAP family. IAP family members usually contain multiple baculovirus IAP repeat (BIR) domains, but BIRC5 has only a single BIR domain. It is expressed cell cycle-dependently and highly expressed at mitosis. As a multitasking protein, BIRC5 has dual roles in promoting cell proliferation and preventing apoptosis. Survivin is a component of a chromosome passage protein complex (CPC) which is essential for chromosome alignment and segregation during mitosis and cytokinesis. Survivin acts as an important regulator of the localization of this complex. It may counteract a default induction of apoptosis in G2/M phase... Read More | Vabicaserin hydrochloride is a 5-hydroxytryptamine 2C ( 5-HT 2C ) receptor -selective agonist with an EC 50 of 8 nM.In VitroVabicaserin displaces 125 I-(2,5-dimethoxy)phenylisopropylamine binding from human 5-HT 2C receptor sites in Chinese hamster ovary cell membranes with a K i value of 3 nM and Vabicaserin hydrochloride is a 5-hydroxytryptamine 2C ( 5-HT 2C ) receptor -selective agonist with an EC 50 of 8 nM.In VitroVabicaserin displaces 125 I-(2,5-dimethoxy)phenylisopropylamine binding from human 5-HT 2C receptor sites in Chinese hamster ovary cell membranes with a K i value of 3 nM and is >50-fold selective over a number of serotonergic, noradrenergic, and dopaminergic receptors. Binding affinity determined for the human 5-HT 2B receptor subtype using [ 3 H]5HT is 14 nM. Vabicaserin is a potent and full agonist (EC 50, 8 nM; E max, 100%) in stimulating 5-HT 2C receptor-coupled calcium mobilization and exhibits 5-HT 2A receptor antagonism and 5-HT 2B antagonist or partial agonist activity in transfected cells, depending on the level of receptor expression. Vabicaserin exhibits lower affinity at the 5-HT 2C antagonist binding site (22 nM) labeled with [ 3 H]mesulergine. Additional binding studies indicate that Vabicaserin possesses affinity for the 5-HT 2B and 5-HT 1A receptors with K i values of 14 and 112 nM, respectively. MCE has not independently confirmed the accuracy of these methods. They are for reference only.In VivoAfter a single oral dose of [ 14 C]Vabicaserin at 50, 5, and 15 mg/kg, unchanged drug represents less than 19, 20, and 35% of total plasma radioactivity at all the time points examined in mice, rats, and dogs, respectively. The carbamoyl glucuronide (CG) represents approximately 7 to 36% of plasma radioactivity in mice and 2 to 28% of plasma radioactivity in dogs but is not detected in rat plasma after the single [ 14 C]Vabicaserin dose. However, the CG is observed in rat plasma after multiple-dose administration of Vabicaserin at higher doses, and the CG is approximately 20 times less than Vabicaserin based on steady-state AUC 0-24 values. The estimated plasma AUC 0-24 ratios of CG to the parent drug are 1.5 and 1.7 in mice and dogs after the single [ 14 C]Vabicaserin dose, respectively. The plasma AUC 0-24 ratios for the CG to Vabicaserin at steady state with doses used for safety assessment are less for mice (0.2-0.6) and slightly higher for dogs (1.8-4.0) compared with the single dose values. The CG is detected in dog urine in similar amounts to the parent drug, although it is not detected in mouse or rat urine after the single [ 14 C]Vabicaserin dose. Radioactivity in a 0- to 24-h bile collection from rats receiving a 5 mg/kg [ 14 C]Vabicaserin dose accounts for 19 and 24% of the administered dose in males and females, respectively. Although the CG is not detected in urine or feces of rats after a single oral administration, it represents an average of up to 30% of biliary radioactivity in male rats and 15% in female rats. In monkeys after a single oral 25-mg/kg dose of Vabicaserin, the plasma concentrations of the CG exceeded those of Vabicaserin at all the time points (2-24 h) postdose, although the amount of CG relative to Vabicaserin decreased by 24 h postdose, with ratios of 17.5 at 2 h and 1.7 at 24 h. The CG to Vabicaserin AUC 0-24 ratio of 12:1 indicates that the CG is a major metabolite in monkeys. MCE has not independently confirmed the accuracy of these methods. They are for reference only.Animal administrationMice and Rats For metabolism studies in mice, rats, and dogs, radiolabeled doses are used. Male and female CD-1 mice and Sprague-Dawley rats are used. The dose vehicle for mice and rats contained 2% (w/w) Tween 80 and 0.5% methylcellulose in water. Nonfasted male and female mice weighing from 27.8 to 33.8 g at the time of dosing are given a single 50-mg/kg (∼300 µCi/kg) dose of Vabicaserin at a volume of 20 mL/kg via intragastric gavage. Mice are kept in metabolic cages in groups of five. Nonfasted male rats weighing from 318 to 345 g and female rats weighing from 227 to 255 g at the time of dosing are given a single 5-mg/kg (∼300 µCi/kg) dose of Vabicaserin at a volume of 2.5 mL/kg via intragastric gavage. Four bile duct-cannulated male rats weighing from 387 to 411 g and four bile duct-cannulated female rats weighing from 291 to 325 g at the time of dosing are nonfasted and are given a single 5-mg/kg (323 µCi/kg) dose of Vabicaserin at a volume of 5.0 mL/kg via intragastric gavage. Rats are kept individually in metabolism cages. Dogs Four male beagle dogs, weighing from 7.6 to 9.8 kg at the time of dosing, are from an in-house colony. Approximately 11 mg of [ 14 C]Vabicaserin hydrochloride and 940 mg of nonlabeled Vabicaserin hydrochloride are dissolved in methanol and then evaporated under a nitrogen stream to dryness. Capsules (number 2) are filled with accurate amounts (126.7-138.1 mg) of the mixed drug substance according to animal weights to give a dosage of 15 mg/kg (39 µCi/kg). The filled gelatin capsules are then enteric-coated manually. Each dog is given one enteric-coated capsule containing [ 14 C]Vabicaserin as the hydrochloride salt. Animals are fed 2 h before dosing and are housed individually in metabolic cages. Monkey Four male cynomolgus monkeys, weighing from 5.4 to 9.6 kg at the time of dosing, are from an in-house colony. Nonfasted monkeys are given a single 25-mg/kg dose of nonradiolabeled Vabicaserin at a volume of 2 mL/kg via intragastric gavage. The vehicle is the same as used in mice and rats. Animals are housed individually in metabolic cages. aladdin has not independently confirmed the accuracy of these methods. They are for reference only.IC50& Target:5-HT 2C Receptor 8 nM (EC 50 )... Read More |