| Description | GCC1 Human Pre-designed siRNA Set A contains three designed siRNAs for GCC1 gene (Human), as well as a negative control, a positive control, and a FAM-labeled negative control. Components GCC1 siRNA-1: 5 nmol (HPLC) GCC1 siRNA-2: 5 nmol (HPLC) GCC1 siRNA-3: 5 nmol (HPLC) siRNA Negative Control: 5 GCC1 Human Pre-designed siRNA Set A contains three designed siRNAs for GCC1 gene (Human), as well as a negative control, a positive control, and a FAM-labeled negative control. Components GCC1 siRNA-1: 5 nmol (HPLC) GCC1 siRNA-2: 5 nmol (HPLC) GCC1 siRNA-3: 5 nmol (HPLC) siRNA Negative Control: 5 nmol (HPLC) FAM-labeled siRNA Negative Control: 5 nmol (HPLC) GAPDH siRNA Positive Control:5 nmol (HPLC)... Read More | Inquire | Taq MasterMix is a premixed system composed of Taq DNA Polymerase, Mg2+, dNTPs, as well as PCR stabilizers and enhancers, with a concentration of 2 ×. The pre prepared PCR mixture makes the operation simpler and faster, and can minimize human error and contamination to the greatest extent Taq MasterMix is a premixed system composed of Taq DNA Polymerase, Mg2+, dNTPs, as well as PCR stabilizers and enhancers, with a concentration of 2 ×. The pre prepared PCR mixture makes the operation simpler and faster, and can minimize human error and contamination to the greatest extent possible. The original MasterMix formula results in high yield, strong repeatability, and good stability of amplified products. This product has been added with a dye (blue), and can be directly subjected to electrophoresis detection after the reaction is completed. The amplified PCR product has an "A" base attached to its 3 'end, making it suitable for direct use in T/A cloning. Mainly suitable for PCR amplification of DNA, DNA sequencing and other experiments. T665590Component5 mL25 mLStorageT665590A2×Taq MasterMix (Dye)5×1 mL5×5 mL-20℃. Avoid freeze/thaw cycle.T665590BddH₂O5×1 mL5×5 mL-20℃. Avoid freeze/thaw cycle.2×Taq MasterMix contains Taq DNA Polymerase, 3 mM Mg Cl₂ and 400 µM each dNTP. Quality control:After testing, there was no exogenous nuclease activity; PCR method for detecting residual DNA without host; Can effectively amplify single copy genes from multiple genomes.Usage:The following is an example of a PCR reaction system and reaction conditions for amplifying a 1 kb fragment using human genomic DNA as a template. In practical operation, corresponding improvements and optimizations should be made based on the template, primer structure, and target fragment size.1. PCR reaction system Reagent 50 µlReaction system Final concentration 2×Taq MasterMix（Dye） 25 µL 1× Forward Primer，10 µM 2 µL 0.4 µM Reverse Primer，10 µM 2 µl 0.4 µM Template DNA <0.5 µg <0.5 µg/50 µL ddH2O up to 50 µL /Attention: The primer concentration should be between 0.1 and 1.0 as the final concentration µ M serves as a reference for setting the range. In the case of low amplification efficiency, the concentration of primers can be increased; When non-specific reactions occur, the primer concentration can be reduced to optimize the reaction system.2. PCR reaction conditions Step Temperature Time / Pre denaturation 94℃ 2 min / Denaturation 94℃ 30 s 25-35 cycles Anneal 55-65℃ 30 s 25-35 cycles Extend 72℃ 30 s 25-35 cycles Finally extended 72℃ 2 min / Attention:1) In general experiments, if the annealing temperature is 5 ° C lower than the melting temperature Tm of the amplification primer, and the ideal amplification efficiency cannot be achieved, the annealing temperature should be appropriately reduced; When non-specific reactions occur, increase the annealing temperature to optimize the reaction conditions.2) The extension time should be set according to the size of the amplified fragment. The amplification efficiency of Taq DNA Polymerase in this product is 2 kb/min.3) The number of cycles can be set based on the downstream application of the amplification product. If the number of cycles is too small, the amplification amount is insufficient; If there are too many cycles, the probability of mismatches will increase, and non-specific backgrounds will be severe. So, while ensuring product yield, the number of cycles should be minimized as much as possible... Read More | Product introduction：Aladdin ® SE is a kind of fluorescent dye with amino reactive activity. The SE group of these dyes can react with the amino group to produce a stable amide bond. Compared with other similar dyes on the market, aladdin ® is a new generation of fluorescent dyes Product introduction：Aladdin ® SE is a kind of fluorescent dye with amino reactive activity. The SE group of these dyes can react with the amino group to produce a stable amide bond. Compared with other similar dyes on the market, aladdin ® is a new generation of fluorescent dyes with stronger stability, better water solubility and better fluorescence intensity. Product parameters： Absmax/Em(nm)：648/664；Absmax/Em(nm)：0.03；Extinction coefficient(ε)：240000；Optimal DOL(IgG)：3-6； Usage:1. Experimental materials(1) IgG: IgG must not contain amine chemicals that can react with dyes, such as amino acids, Tris, BSA, gelatin, etc. If IgG contains such chemicals, PBS buffer with pH~7.4 should be used for pre dialysis treatment. The presence of azide compounds does not affect the labeling reaction.(2) Anhydrous DMSO(3) NaHCO3(4) Sephadex gel G-25 dialysis column(5) PBS buffer (pH~7.4)(6) NaN3(7) BSA2. Marking methods and steps(1) Prepare to label antibodiesDilute the antibody with 0.1 M NaHCO3 solution (pH~8.3) to a final concentration of 2.5 mg/mL. If the product is pre diluted with phosphate buffer, such as PBS buffer (without amino compounds), approximately 1/10 volume of 1M NaHCO3 mother liquor can be directly added to the buffer to achieve a final NaHCO3 concentration of 0.1 M.Note: When the protein concentration is 2.5 mg/mL, the labeling efficiency is approximately 35%. Protein concentrations below 2.5 mg/mL can also be used for labeling, but the labeling efficiency will decrease. When the protein concentration is higher than 5 mg/mL, the labeling efficiency may be higher. Due to differences in buffer and protein purity, more precise labeling efficiency is determined by practical operating conditions. If the protein concentration is too low, it can be concentrated by ultrafiltration.(2) Prepare dye storage solutionPreheat one tube at room temperature µ YF of Mole ® SE, add 0.1 mL of anhydrous DMSO to the tube, thoroughly vortex dissolve the dye, and prepare a dye storage solution with a concentration of 10 mM. If a trace amount of protein is used for labeling reactions, the dye needs to be diluted to a lower concentration.Note: a The remaining dye storage solution should be stored at a low temperature of -20 ℃ for future use. If anhydrous DMSO is used to prepare dye storage solution, the dye can be stored for at least one month.b. Dyes can also be prepared with deionized water, but due to the slow hydrolysis of dyes in water, it is best to prepare water based storage solutions for immediate use.(3) Mark reaction stepsa. Stir or vortex the protein solution, gradually adding 15-25 drops µ L dye storage solution (10 mM), with a molar ratio of dye/protein in the range of 9:1 to 15:1. YF ® Please refer to the table above for the range of DOL (number of dyes bound to each protein molecule) for SE labeled IgG antibodies.b. Stir the reaction at room temperature for 1 hour, and for trace labeling, shake and incubate on a shaker for 1 hour.Note: At the same time of the binding reaction, proceed to step 2 (4) to balance the dextran gel G-25 dialysis column.(4) Isolation of marker proteins from reaction solutiona. PBS buffer (pH~7.4) was used to balance the dextran gel G-25 dialysis column (10 mm × 300 mm).b. Add the reaction solution from step 3 (b) to the column and elute with 1 x PBS buffer.The first washed out chromophore is a dye protein complex.Note: a For small-scale labeling reactions, in order to avoid excessive dilution of the product, ultrafiltration devices can be used to remove free dyes from the complex.b. After the binding reaction is completed, if the dye protein complex is not separated in time, 50 can be added µ Terminate the reaction with L 1M lysine. In most cases, this operation is not necessary because the remaining unreacted dyes have been fully hydrolyzed at the end of the reaction.3. Determine DOL(1) The determination of protein concentration and antibody concentration can be calculated using the following formula:C (mg/mL)={[A280- (Amax x x Cf)]/1.4} x dilution factor;a. C refers to the concentration of antibodies collected in the experiment;b. Dilution factor refers to the dilution factor used in photometric measurements;c. A280 and Amax refer to the absorbance at 280 nm and the absorbance at the absorption wavelength, respectively;d. Cf is the correction factor, YF ® Please refer to the table above for the Cf value of SE dyes;Note: The protein solution eluted through the column may have a high concentration when used directly for absorbance detection, so it needs to be diluted to approximately 0.1 mg/mL. The dilution factor (i.e. dilution factor) needs to be determined from the initial number of antibodies (e.g. 5 mg) and the overall elution of protein solutionEstimate based on the product.(2) Estimation of DOLDOL is calculated using the following equation:DOL=(Amax x x Mwt x Dilution Factor)/（ ε X C)a. Amax, dilution factor, C value has been clearly defined in 3 (1);b. Mwt refers to the molecular weight of IgG (150000);C. c ε It's YF ® The molar absorption coefficient of SE, refer to the table on the first page;d. Mark YF ® The optimal DOL value for SE IgG antibodies can be found in the table on the first page. Although DOL values may fluctuate, good experimental results can also be achieved.Matters needing attention：1. if the labeled protein needs long-term storage, it is recommended to add 5-10 mg/ml BSA and 0.01-0.03% NaN3 to prevent protein denaturation and microbial breeding. Store at 4 ℃ away from light. If glycerol with a final concentration of 50% is added, it can be stored at -20 ℃. It can be stably stored for more than one year. 2. keep away from light during operation. The mixing speed should be appropriate to avoid bubbles. 3. when installing the chromatographic column, try to make the column body uniform, the column surface flat, and free of bubbles and cracks. 4. pay attention to adding the sample when the column top buffer is tangent to the gel plane. When eluting, add the eluent when the sample is tangent to the gel plane. 5. other factors affecting the labeling efficiency also include temperature, reaction time, pH, the amount of fluorescent dye and protein, etc., which should be controlled. 6. for your safety and health, please wear laboratory clothes and disposable gloves.Scope of application：Protein nucleic acid labeling dye... Read More | Protein Purity≥85% by SDS PAGEExtinction CoeffA280 nm = 0.631 at 1.0 mg/ml for pure C1qMolecular Weight400,000 Da (18 chains)General DescriptionRat C1q is purified from pooled normal rat serum. C1q is part of the C1 complex, which is the first complement component in the classical pathway of Protein Purity≥85% by SDS PAGEExtinction CoeffA280 nm = 0.631 at 1.0 mg/ml for pure C1qMolecular Weight400,000 Da (18 chains)General DescriptionRat C1q is purified from pooled normal rat serum. C1q is part of the C1 complex, which is the first complement component in the classical pathway of complement. The C1 complex is a non-covalent assembly of three different proteins (C1q, C1r, and C1s) bound together in a calcium-dependent complex. C1q has six extended arms with domains at the end of each arm that bind to the Fc domains of immunoglobulins such as IgG or IgM. When antibodies bind toantigens, forming immune complexes, they cluster allowing two or more of the six C1q arms to bind to the Fc domains of antibodies. Rat IgG2 is very efficient when compared to IgG1 in activating complement (Medgyesi, G.A et., al., 1981). This is in contrast to the human system in which IgG1 activates complement but not IgG2 (Redpath, S. et. al., 1998). The binding of multiple arms of C1q to immune complexes causes the two C1r proteins in the complex (protease zymogens) to auto-activate. The activated C1r proteases cleave and activate the two C1s protease zymogens in the complex. The activated C1s cleaves complement component C4 releasing C4a and initiating covalent attachment of C4b to the activating surface. Activated C1s also cleaves C2 and the larger fragment of C2 binds to the surface-attached C4b forming C4b,C2a, the C3/C5 convertase of the classical pathway.Rat IgG1 cannot activate complement whereas rat IgG2 does.Physical Characteristics & StructureThe apparent molecular weight of rat C1q as determined by gel filtration has been reported to be 400,000 by Veerhuis, R. et al., (1985) and is calculated to be 420,000 based on its amino acid sequence. Rat C1q is a high molecular weight complex of 18 polypeptide chains. Each of the six arms of rat C1q contains three chains, an A chain (~30,000 daltons), a B chain (~28,000 daltons) and a C chain (~26,000 daltons) as determined by SDS/polyacrylamide gel electrophoresis (Wing, M.G. et al., (1993)).FunctionThe biological functions of C1q are described above in the General Description and Physical Characteristics sections.ApplicationsRat C1q can be used to coat ELISA plates to capture and quantitate immune complexes in samples from rat models used for studying immune complex related diseases and conditions.GeneticsNCBI Gene ID numbers for rat C1q are: C1q A chain (298566), C1q B chain (29687), and C1q C chain (362634). The genes for C1q chains A, B and C are all located on chromosome 5. The UniprotKB primary accession numbers for rat C1q are: C1q A chain (P31720), C1q B chain (P31721), and C1q C chain (P31722).Precautions/Toxicity/HazardsThis protein is purified from animal plasma/serum and therefore precautions appropriate for handling any animal blood-derived product must be used.ReferencesMedgyesi, G.A et., Miklos, K., Kulics, J., Fust, G., and Gergely, J. Bazin, H. (1981). Classes and subclasses of rat antibodies: reaction with the antigen and interaction of the complex with the complement system. Immunology 43, 171-176.Redpath, S., Michaelsen, T., Sandlie, I. and Clark, M. R. (1998). Activation of complement by human IgG1 and human IgG3 antibodies against the human leucocyte antigen CD52. Immunology 93, 595–600.Veerhuis, R., Van Es, L.A. and Daha, M.R. (1985). In vivo degradation of rat C1q induced by intravenous injection of soluble IgG aggregates. Immunology 54, 801-810.Wing, M.G., Seilly, D. J., Bridgman, D.J. and Harrison, R.A. (1993). Rapid isolation and biochemical characterization of rat C1 and C1q. Molecular Immunology 30, 433-440... Read More |