| Description | CSF2RA Human Pre-designed siRNA Set A contains three designed siRNAs for CSF2RA gene (Human), as well as a negative control, a positive control, and a FAM-labeled negative control. Components CSF2RA siRNA-1: 5 nmol (HPLC) CSF2RA siRNA-2: 5 nmol (HPLC) CSF2RA siRNA-3: 5 nmol (HPLC) siRNA Negative CSF2RA Human Pre-designed siRNA Set A contains three designed siRNAs for CSF2RA gene (Human), as well as a negative control, a positive control, and a FAM-labeled negative control. Components CSF2RA siRNA-1: 5 nmol (HPLC) CSF2RA siRNA-2: 5 nmol (HPLC) CSF2RA siRNA-3: 5 nmol (HPLC) siRNA Negative Control: 5 nmol (HPLC) FAM-labeled siRNA Negative Control: 5 nmol (HPLC) GAPDH siRNA Positive Control:5 nmol (HPLC)... Read More | Carboxypeptidase B catalyzes hydrolysis of the basic amino acids lysine, arginine and histidine from theC-terminal end of polypeptides. The molecular weight is 34,500 daltons, the pH optimum is 8.0, and pI is 6.0.Carboxypeptidase B is competitively inhibited by arginine and lysine. The enzyme is Carboxypeptidase B catalyzes hydrolysis of the basic amino acids lysine, arginine and histidine from theC-terminal end of polypeptides. The molecular weight is 34,500 daltons, the pH optimum is 8.0, and pI is 6.0.Carboxypeptidase B is competitively inhibited by arginine and lysine. The enzyme is also inhibited by metal chelating agents, e.g., EDTA. Recombinant Carboxypeptidase B (EC 3.4.17.2) is expressed in E.Coli and purified by high pressure liquid chromatography. There is no trace of other enzyme (such as carboxypeptidase A and chymotrypsin) activity. No protease inhibitors such as PMSF are present in the preparation.Animal origin free:eliminate the risk of virus presence, or of any other potential adventitious agents found in animal-derived carboxypeptitase B.Stability:A sterile recombinant carboxypeptidase B lyophilized eliminates the risk of contamination and decreases the chances of activity loss in the process of transport and storage. High purity:1) Recombinant carboxypeptidase B provides increased specific activity and eliminates contaminating protease activities found in extracted enzymes with lower purity level. 2) No other contaminating proteases such as chymotrypsin and carboxypeptidase A. 3）Less than 10ppm of recombinant trypsin... Read More | Protein:BSA-Free | This reagent kit is based on TRIzon's improved columnar total RNA extraction kit. This product can be extracted from animal groupsExtract total RNA from samples such as textiles, plant materials, various microorganisms, and cultured cells. Firstly, the cracking solution is fully cracked This reagent kit is based on TRIzon's improved columnar total RNA extraction kit. This product can be extracted from animal groupsExtract total RNA from samples such as textiles, plant materials, various microorganisms, and cultured cells. Firstly, the cracking solution is fully cracked andHomogenized samples, in their unique high salt state, RNA specifically binds to silicon matrix membranes, greatly reducingEffectively removing organic solvent contamination while removing protein contamination, resulting in higher purity and quality of RNA. bookThe product can quickly extract total RNA from various cells or tissues, and can process 30-50 mg of tissue or 5 × 10 ⁶ cells each time,Can handle multiple different samples simultaneously. If it is an RNA experiment that is very sensitive to trace amounts of DNA, the residual DNA can be utilizedUsing DNase without RNase for digestion and removal on the column, the extracted RNA can be directly applied to RT-PCR Experiments such as Northern Blot, Dot Blot, and in vitro translation. U665516 Component 50 T Storage U665516A DNase I 1000 U -20℃. Avoid freeze/thaw cycle. U665516B 10×Reaction Buffer 1000 µL -20℃. Avoid freeze/thaw cycle. U665516C TRIzon Reagent 60 mL 2-8℃. Protect from light. U665516D TRIzon PaI™ 10 mL 2-8℃. Protect from light. U665516E Buffer RW1 40 mL RT U665516F Buffer RW2 (concentrate) 11 mL RT U665516G RNase-Free Water 10 mL RT U665516H Spin Columns RM with Collection Tubes 50 sets RT U665516I RNase-Free Centrifuge Tubes (1.5 mL) 50 EA RTPreparation and important precautions before the experiment:1.To prevent RNase pollution, attention should be paid to the following aspects:1) RNase's plastic products and gun heads to avoid cross contamination.2) Prepare the solution using water without RNase.3) Operators should wear disposable masks and gloves, and change gloves frequently during the experiment.2. The sample should avoid repeated freezing and thawing, otherwise it will affect the yield and quality of RNA extraction.3. If TRIzon Reagent is found to have precipitates before use, it can be dissolved in a water bath at 56 ℃ for a few minutes.Before the first use, anhydrous ethanol should be added to Buffer RW2 according to the instructions on the reagent bottle label.5. All centrifugation steps should be carried out at room temperature unless otherwise specified, and all operation steps should be carried out quickly.Usage：1. Sample processing1a. Organization: 30-50 mg of tissue is thoroughly ground in liquid nitrogen and 1 mL of TRIzon Reagent is added, or 1 mL of TRIzon Reagent is added to the tissue sample and homogenized. Attention: The sample volume should not exceed 10% of the volume of TRIzon Reagent.2a. Single layer cell culture: Remove the culture medium and add an appropriate amount every 10 cm ² Add 1 mL of TRIzon Reagent.3a. Cell suspension: Collect cells by centrifugation. Add 1 mL of TRIzon Reagent to every 5 × 10 µ m cell.2. After adding TRIzon Reagent, repeatedly blow a few times to fully crack the sample. Leave at room temperature for 5 minutes to completely separate the protein nucleic acid complex.3. Add 200 to every 1 mL of TRIzon Reagent µ LTRIzon PaI ™， Cover the tube tightly, vigorously shake for 15 seconds, and let it sit at room temperature for 2 minutes.4. Centrifuge at 4 ℃ 12000 rpm (~13400 × g) for 10 minutes. At this time, the sample is divided into three layers: the red organic phase, the middle layer, and the upper colorless aqueous phase. RNA is mainly in the upper aqueous phase. Move the upper aqueous phase to a new RNase Free centrifuge tube (provided).5. Add an equal volume of 70% ethanol (prepared without RNase water) to the obtained aqueous solution, invert and mix well.6. Add all the solutions obtained in the previous step to the spin columns RM that have been loaded into the collection tube. If the solution cannot be added at once, it can be transferred in multiple batches. Centrifuge at 12000 rpm for 20 seconds, discard the waste liquid in the collection tube, and place the adsorption column back into the collection tube.7. Add 350 to the adsorption column µ L Buffer RW1, centrifuge at 12000 rpm for 20 seconds, discard the waste liquid in the collection tube, and place the adsorption column back into the collection tube.8. Preparation of DNase I mixture: Take 52 µ LRNase Free Water, add 8 to it µ L 10 x Reaction Buffer and 20 µ L DNase I (1 U/ µ L) Mix well and prepare to a final volume of 80 µ The reaction solution of L.9. Directly add 80 µ L DNase I mixture to the adsorption column and incubate at 20-30 ℃ for 15 minutes.10. Add 350 to the adsorption column µ L Buffer RW1, centrifuge at 12000 rpm for 1 minute, discard the waste liquid, and place the adsorption column back into the recovery manifold.11. Add 500 to the adsorption column µ L Buffer RW2 (check if anhydrous ethanol has been added before use), centrifuge at 12000 rpm for 20 seconds, discard the waste liquid in the collection tube, and place the adsorption column back into the collection tube.12. Repeat step 11.Centrifuge at 12000 rpm for 2 minutes and discard the waste liquid from the collection tube. Place the adsorption column at room temperature for a few minutes and thoroughly air dry. Attention: The purpose of this step is to remove residual ethanol from the adsorption column, which will affect subsequent enzymatic reactions (enzyme digestion,. )PCR, etc.14. Place the adsorption column in a new RNase free centrifuge tube and add 30-50 to the middle of the adsorption column µ Place RNase Free Water at room temperature for 1 minute, centrifuge at 12000 rpm for 1 minute, collect RNA solution, and store RNA at -70 ℃ to prevent degradation.Attention:1) The volume of RNase Free Water should not be less than 30 µ L. Small volume affects the recovery rate.2) If you want to increase RNA production, you can use 30-50 µ Repeat step 14 for the new RNase Free Water.3) If you want to increase the RNA concentration, you can add the obtained solution back to the adsorption column and repeat step 14... Read More | Vabicaserin hydrochloride is a 5-hydroxytryptamine 2C ( 5-HT 2C ) receptor -selective agonist with an EC 50 of 8 nM.In VitroVabicaserin displaces 125 I-(2,5-dimethoxy)phenylisopropylamine binding from human 5-HT 2C receptor sites in Chinese hamster ovary cell membranes with a K i value of 3 nM and Vabicaserin hydrochloride is a 5-hydroxytryptamine 2C ( 5-HT 2C ) receptor -selective agonist with an EC 50 of 8 nM.In VitroVabicaserin displaces 125 I-(2,5-dimethoxy)phenylisopropylamine binding from human 5-HT 2C receptor sites in Chinese hamster ovary cell membranes with a K i value of 3 nM and is >50-fold selective over a number of serotonergic, noradrenergic, and dopaminergic receptors. Binding affinity determined for the human 5-HT 2B receptor subtype using [ 3 H]5HT is 14 nM. Vabicaserin is a potent and full agonist (EC 50, 8 nM; E max, 100%) in stimulating 5-HT 2C receptor-coupled calcium mobilization and exhibits 5-HT 2A receptor antagonism and 5-HT 2B antagonist or partial agonist activity in transfected cells, depending on the level of receptor expression. Vabicaserin exhibits lower affinity at the 5-HT 2C antagonist binding site (22 nM) labeled with [ 3 H]mesulergine. Additional binding studies indicate that Vabicaserin possesses affinity for the 5-HT 2B and 5-HT 1A receptors with K i values of 14 and 112 nM, respectively. MCE has not independently confirmed the accuracy of these methods. They are for reference only.In VivoAfter a single oral dose of [ 14 C]Vabicaserin at 50, 5, and 15 mg/kg, unchanged drug represents less than 19, 20, and 35% of total plasma radioactivity at all the time points examined in mice, rats, and dogs, respectively. The carbamoyl glucuronide (CG) represents approximately 7 to 36% of plasma radioactivity in mice and 2 to 28% of plasma radioactivity in dogs but is not detected in rat plasma after the single [ 14 C]Vabicaserin dose. However, the CG is observed in rat plasma after multiple-dose administration of Vabicaserin at higher doses, and the CG is approximately 20 times less than Vabicaserin based on steady-state AUC 0-24 values. The estimated plasma AUC 0-24 ratios of CG to the parent drug are 1.5 and 1.7 in mice and dogs after the single [ 14 C]Vabicaserin dose, respectively. The plasma AUC 0-24 ratios for the CG to Vabicaserin at steady state with doses used for safety assessment are less for mice (0.2-0.6) and slightly higher for dogs (1.8-4.0) compared with the single dose values. The CG is detected in dog urine in similar amounts to the parent drug, although it is not detected in mouse or rat urine after the single [ 14 C]Vabicaserin dose. Radioactivity in a 0- to 24-h bile collection from rats receiving a 5 mg/kg [ 14 C]Vabicaserin dose accounts for 19 and 24% of the administered dose in males and females, respectively. Although the CG is not detected in urine or feces of rats after a single oral administration, it represents an average of up to 30% of biliary radioactivity in male rats and 15% in female rats. In monkeys after a single oral 25-mg/kg dose of Vabicaserin, the plasma concentrations of the CG exceeded those of Vabicaserin at all the time points (2-24 h) postdose, although the amount of CG relative to Vabicaserin decreased by 24 h postdose, with ratios of 17.5 at 2 h and 1.7 at 24 h. The CG to Vabicaserin AUC 0-24 ratio of 12:1 indicates that the CG is a major metabolite in monkeys. MCE has not independently confirmed the accuracy of these methods. They are for reference only.Animal administrationMice and Rats For metabolism studies in mice, rats, and dogs, radiolabeled doses are used. Male and female CD-1 mice and Sprague-Dawley rats are used. The dose vehicle for mice and rats contained 2% (w/w) Tween 80 and 0.5% methylcellulose in water. Nonfasted male and female mice weighing from 27.8 to 33.8 g at the time of dosing are given a single 50-mg/kg (∼300 µCi/kg) dose of Vabicaserin at a volume of 20 mL/kg via intragastric gavage. Mice are kept in metabolic cages in groups of five. Nonfasted male rats weighing from 318 to 345 g and female rats weighing from 227 to 255 g at the time of dosing are given a single 5-mg/kg (∼300 µCi/kg) dose of Vabicaserin at a volume of 2.5 mL/kg via intragastric gavage. Four bile duct-cannulated male rats weighing from 387 to 411 g and four bile duct-cannulated female rats weighing from 291 to 325 g at the time of dosing are nonfasted and are given a single 5-mg/kg (323 µCi/kg) dose of Vabicaserin at a volume of 5.0 mL/kg via intragastric gavage. Rats are kept individually in metabolism cages. Dogs Four male beagle dogs, weighing from 7.6 to 9.8 kg at the time of dosing, are from an in-house colony. Approximately 11 mg of [ 14 C]Vabicaserin hydrochloride and 940 mg of nonlabeled Vabicaserin hydrochloride are dissolved in methanol and then evaporated under a nitrogen stream to dryness. Capsules (number 2) are filled with accurate amounts (126.7-138.1 mg) of the mixed drug substance according to animal weights to give a dosage of 15 mg/kg (39 µCi/kg). The filled gelatin capsules are then enteric-coated manually. Each dog is given one enteric-coated capsule containing [ 14 C]Vabicaserin as the hydrochloride salt. Animals are fed 2 h before dosing and are housed individually in metabolic cages. Monkey Four male cynomolgus monkeys, weighing from 5.4 to 9.6 kg at the time of dosing, are from an in-house colony. Nonfasted monkeys are given a single 25-mg/kg dose of nonradiolabeled Vabicaserin at a volume of 2 mL/kg via intragastric gavage. The vehicle is the same as used in mice and rats. Animals are housed individually in metabolic cages. aladdin has not independently confirmed the accuracy of these methods. They are for reference only.IC50& Target:5-HT 2C Receptor 8 nM (EC 50 )... Read More |