| Description | GBX2 Human Pre-designed siRNA Set A contains three designed siRNAs for GBX2 gene (Human), as well as a negative control, a positive control, and a FAM-labeled negative control. Components GBX2 siRNA-1: 5 nmol (HPLC) GBX2 siRNA-2: 5 nmol (HPLC) GBX2 siRNA-3: 5 nmol (HPLC) siRNA Negative Control: 5 GBX2 Human Pre-designed siRNA Set A contains three designed siRNAs for GBX2 gene (Human), as well as a negative control, a positive control, and a FAM-labeled negative control. Components GBX2 siRNA-1: 5 nmol (HPLC) GBX2 siRNA-2: 5 nmol (HPLC) GBX2 siRNA-3: 5 nmol (HPLC) siRNA Negative Control: 5 nmol (HPLC) FAM-labeled siRNA Negative Control: 5 nmol (HPLC) GAPDH siRNA Positive Control:5 nmol (HPLC)... Read More | EPOCROSTM is a reactive polymer with an oxazoline group on the side chain and is used as a cross-linking agent for water-based resins. Among the water-based polymers developed to address environmental issues and the increasing use of water-based products due to VOC regulations and desolventing, the EPOCROSTM is a reactive polymer with an oxazoline group on the side chain and is used as a cross-linking agent for water-based resins. Among the water-based polymers developed to address environmental issues and the increasing use of water-based products due to VOC regulations and desolventing, the EPOCROSTM WS series is a “water-soluble type” with the following structure.Features and PropertiesHigher reactivity than water-based epoxy, melamine, blocked isocyanateVOC free (EPOCROS™ WS-300 and EPOCROS™ WS-700)High crosslinking density with a small amount addedOne-pack type with long usage timeImproves water resistance, solvent resistance, heat resistance, and the strength of films, etc.Adhesion-imparting possible to PET, OPP, PVC, etc.Fast dryingLow toxicity (Ames Test: Negative, Primary Skin Irritation Test: No irritation)WS Series Product LineupApplicationsNonwoven fabric bindersPigment printingCoatings (metals, films, leather)Paint and coatings, Primers (plastics, building materials, vehicles)AdhesivesMethodASSAY for Product Code DILW:One unit equals a decrease in absorbance of 1.0 per minute at 25°C at pH 7.5 with 2,6-dichlorophenolindophenol as the chromogen.Reagents0.2 M Tris⋅HCl buffer, pH 7.50.006 M NADH. Prepare fresh daily.0.0012 M Dichlorophenolindophenol (DCPIP) Prepare fresh daily.EnzymePrepare a 10 mg/ml solution of enzyme in 0.2 M Tris⋅HCl, pH 7.5.Dilute further immediately before use to give ΔA/min of 0.15-0.20.ProcedureAdjust spectrophotometer to 600 nm and 25°C.Pipette into cuvettes as follows:Mix quickly and measure the decrease in absorbance at 600 nm for 2-3 minutes.Determine the ΔA/min. from the initial linear portion of the curve. (Use portion of curve from t=0 to t=1 minute; the rate is linear for 1/2 to 1 minute.)Calculation... Read More | Inquire | Product contentF665774Component5 mLStorageF665774A2×Fast Probe Mixture5×1 mL-20℃. Avoid freeze/thaw cycle.F665774B50×High ROX200 µL-20℃. Avoid freeze/thaw cycle.F665774CddH2O5×1 mL-20℃. Avoid freeze/thaw cycle.Product IntroductionFast Probe Mixture is a preProduct contentF665774Component5 mLStorageF665774A2×Fast Probe Mixture5×1 mL-20℃. Avoid freeze/thaw cycle.F665774B50×High ROX200 µL-20℃. Avoid freeze/thaw cycle.F665774CddH2O5×1 mL-20℃. Avoid freeze/thaw cycle.Product IntroductionFast Probe Mixture is a pre-mixed system for real-time fluorescence PCR by probe method (TaqMan, Molecular Beacon, etc.), with a concentration of 2×, including Fast Taq DNA Polymerase, PCR Buffer, dNTPs, Mg2+ and so on, which is easy and convenient to operate. It is mainly used for the detection of genomic DNA target sequence and cDNA target sequence after RNA reverse transcription. The Fast Taq DNA Polymerase contained in this product can effectively reduce the non-specific amplification generated by the non-specific binding of primers and templates or primer dimerization at room temperature, and the activation of the enzyme only needs to be incubated at 95 ℃ for 30 s. The whole PCR reaction process can save about 40 minutes compared with the ordinary reaction, which greatly shortens the reaction time of PCR. The combination of unique PCR buffer system and fast hot start enzyme effectively inhibits the generation of non-specific products and significantly improves the PCR amplification efficiency with stronger fluorescence signal, higher sensitivity and wider linear range. The product has a wide range of applications and can be used for both normal and rapid quantitative PCR programs.ROX dye is used to correct the fluorescence signal error generated between wells of a quantitative PCR instrument, and is generally used in Real Time PCR amplifiers from ABI, Stratagene, and other companies. The excitation optics vary from instrument to instrument, so the concentration of ROX dye must be matched to the corresponding fluorescence quantitative PCR instrument.Instruments that do not require ROX calibration (F665766):Roche LightCycler 480, Roche LightCyler 96, Bio-rad iCyler iQ, iQ5, CFX96 and others.Instruments that require Low ROX calibration (F665768):ABI Prism7500/7500 Fast, QuantStudio®3 System, QuantStudio®5 System, QuantStudio®6 Flex System, QuantStudio®7 Flex System, ViiA 7 system. Stratagene Mx3000/Mx3005P, Corbett Rotor Gene 3000, and more.Instruments that require High ROX calibration (F665774):ABI Prism 7000/7300/7700/7900, Eppendorf, ABI Step One/Step One Plus, and others.matters needing attention1. Before use, please mix gently by turning up and down, avoid foaming as much as possible, and use after brief centrifugation.2. Avoid repeated freezing and thawing of this product, repeated freezing and thawing may degrade the product performance. This product can be stored for long term at -20℃, protected from light. If frequent use is required within a short period of time, it can be stored at 2-8℃.UsageThe following examples are conventional PCR reaction systems and reaction conditions, which should be improved and optimized according to the template, primer structure and target fragment size in actual operation.1.PCR reaction systemreagents50µl reaction systemfinal concentration2×Fast Probe Mixture25 µl1×Forward Primer, 10µM1µl0.2µM¹⁾Reverse Primer, 10µM1µl0.2µM¹⁾Probe, 10 µM1µl0.2µM²⁾Template DNA2µl³⁾ 50x Low ROX or High ROX(optional)⁴⁾1µl1×ddH₂Oup to 50µlNote: 1) Usually the primer concentration of 0.2µM can get better results, and 0.1-1.0µM can be used as a reference for setting the range. 2) The final concentration of the probe used is related to the fluorescent quantitative PCR instrument used, the type of probe, and the type of fluorescent labeling substance, so please refer to the instruction manual of the instrument or the specific requirements of the use of each fluorescent probe for the adjustment of the concentration in actual use.(3) Usually the amount of DNA template is 10-100ng genomic DNA or 1-10ng cDNA as a reference. Since the templates of different species contain different copy numbers of target genes, the templates can be subjected to gradient dilution to determine the optimal amount of template to be used.(4) The excitation optical system varies from instrument to instrument, choose to add 50×Low ROX or 50×High ROX according to the instrument using fluorescence quantification.2. PCR reaction program:A two-step PCR reaction program is recommended, and this program is set up using the ABI 7500 Fluorescent Quantitative PCR Instrument as a reference.Note: 1) The enzyme used in this product must be pre-denatured at 95°C for 30s to achieve enzyme activation. Under this condition, most of the templates can be well unchained. For templates with high GC content and complex secondary structure, the pre-denaturation time can be extended to 1-4 minutes to allow the starting template to fully unchain.(2) It is recommended to use two-step PCR reaction program, if you do not get good experimental results due to the use of primers with lower Tm values, etc., you can try to carry out three-step PCR amplification, and the annealing temperature, please use the range of 56 ℃ - 64 ℃ as a setting reference... Read More | Reverse transcriptases are enzymes encoded in retroviruses viral genome. The enzyme is responsible for transcription of the viral RNA to produce a dsDNA that can be inserted into the host genome.Reverse transcriptases are multifunctional enzymes. These enzymes exhibit an RNA and DNA directed Reverse transcriptases are enzymes encoded in retroviruses viral genome. The enzyme is responsible for transcription of the viral RNA to produce a dsDNA that can be inserted into the host genome.Reverse transcriptases are multifunctional enzymes. These enzymes exhibit an RNA and DNA directed polymerase activity. In addition reverse transcriptases catalyze the degradation of RNA in an RNA-DNA hybrid. The exonucleolytic activity proceeds in a 5' ---> 3' direction. The RNA or DNA directed activity requires a template (RNA or DNA) and a primer. The following is a schematic illustration of the reaction:Unit definition: One unit incorporates 1 nanomole of tritiated dTMP into acid insoluble productsusing poly(A)•oligo(dT) 12-18 as the template-primer in 20 minutes at 37° C.ApplicationsHIV reverse transcriptase is used for research on the AIDS primer. However it can be substituted for AMV reverse transcriptase, which is mainly used to transcribe mRNA into double stranded cDNA, that can be inserted into prokaryotic vectors. The enzyme can also be used with either single stranded DNA or RNA templates to make probes for use in hybridization experiments. It can be used for labeling the termini of DNA fragments with protruding 5' termini. The enzyme can also be used to sequence DNAs by the dideoxy chain termination method of Sanger when the Klenow fragment of E. coli DNA polymerase I, or the T7 DNA polymerase yield unsatisfactory results.Reagents0.05 M Tris, pH 8.3, containing 0.008 M MgCl21 mg/ml polyadenylic acid in water (poly A)DNA primer:Oligo d(T)12-181 µ mole dTTP/mL stock solution[methyl-3H]-Thymidine 5'-triphosphate (3H-dTTP)dTTP-3H-dTTP working mix: Add 1-2 µL 3H-dTTP per mL of 100 nmol/mL dTTP in order to obtain 1 to 1.5 x 105 cpm/mL1% bovine serum albumin10% perchloric acid1% perchloric acidBuffer substrate reaction mixture: Prepare fresh, immediately before use:For each 1mL of reaction mixture required mix:0.7 mL Tris/HCl, pH 8.3, 0.008M MgCl20.3 mL 1 mg/mL poly(A) RNA template0.005 mL 0.02 mg/mL oligo d(T)12-18 DNA primer0.02mL 1% BSAEnzymedilute as needed wtih 0.05M Tris/HCl, pH 8.3, 0.008M MgCl2 containing 0.1 mg/mL (1%) BSAProcedurePipette into each tube as follows:Buffer substrate mix：0.1 mLdTTP-3H3-dTTP：0.1 mLEnzyme：5-10 µLIncubate 20 minutes at 37° C. Stop reaction by adding 1 ml 10% cold perchloric acid. Filter through 0.2µ manifold filters used with Millipore vacuum manifold. Wash four times using 2mL 1% cold perchloric acid/wash. Transfer filter to scintillation vials. Add 2mL Cellosolve (or 2-methoxyethanol) to dissolve filter. Filters become opaque upon addition of Cellosolve. Make sure filters are dissolved before proceeding. Add 10mL scintillation cocktail and count.Calculation... Read More |