| Description | ATN1 Human Pre-designed siRNA Set A contains three designed siRNAs for ATN1 gene (Human), as well as a negative control, a positive control, and a FAM-labeled negative control. Components ATN1 siRNA-1: 5 nmol (HPLC) ATN1 siRNA-2: 5 nmol (HPLC) ATN1 siRNA-3: 5 nmol (HPLC) siRNA Negative Control: 5 ATN1 Human Pre-designed siRNA Set A contains three designed siRNAs for ATN1 gene (Human), as well as a negative control, a positive control, and a FAM-labeled negative control. Components ATN1 siRNA-1: 5 nmol (HPLC) ATN1 siRNA-2: 5 nmol (HPLC) ATN1 siRNA-3: 5 nmol (HPLC) siRNA Negative Control: 5 nmol (HPLC) FAM-labeled siRNA Negative Control: 5 nmol (HPLC) GAPDH siRNA Positive Control:5 nmol (HPLC)... Read More | Inquire | Taq MasterMix is a premixed system composed of Taq DNA Polymerase, Mg2+, dNTPs, as well as PCR stabilizers and enhancers, with a concentration of 2 ×. The pre prepared PCR mixture makes the operation simpler and faster, and can minimize human error and contamination to the greatest extent Taq MasterMix is a premixed system composed of Taq DNA Polymerase, Mg2+, dNTPs, as well as PCR stabilizers and enhancers, with a concentration of 2 ×. The pre prepared PCR mixture makes the operation simpler and faster, and can minimize human error and contamination to the greatest extent possible. The original MasterMix formula results in high yield, strong repeatability, and good stability of amplified products. This product has been added with a dye (blue), and can be directly subjected to electrophoresis detection after the reaction is completed. The amplified PCR product has an "A" base attached to its 3 'end, making it suitable for direct use in T/A cloning. Mainly suitable for PCR amplification of DNA, DNA sequencing and other experiments. T665590Component5 mL25 mLStorageT665590A2×Taq MasterMix (Dye)5×1 mL5×5 mL-20℃. Avoid freeze/thaw cycle.T665590BddH₂O5×1 mL5×5 mL-20℃. Avoid freeze/thaw cycle.2×Taq MasterMix contains Taq DNA Polymerase, 3 mM Mg Cl₂ and 400 µM each dNTP. Quality control:After testing, there was no exogenous nuclease activity; PCR method for detecting residual DNA without host; Can effectively amplify single copy genes from multiple genomes.Usage:The following is an example of a PCR reaction system and reaction conditions for amplifying a 1 kb fragment using human genomic DNA as a template. In practical operation, corresponding improvements and optimizations should be made based on the template, primer structure, and target fragment size.1. PCR reaction system Reagent 50 µlReaction system Final concentration 2×Taq MasterMix（Dye） 25 µL 1× Forward Primer，10 µM 2 µL 0.4 µM Reverse Primer，10 µM 2 µl 0.4 µM Template DNA <0.5 µg <0.5 µg/50 µL ddH2O up to 50 µL /Attention: The primer concentration should be between 0.1 and 1.0 as the final concentration µ M serves as a reference for setting the range. In the case of low amplification efficiency, the concentration of primers can be increased; When non-specific reactions occur, the primer concentration can be reduced to optimize the reaction system.2. PCR reaction conditions Step Temperature Time / Pre denaturation 94℃ 2 min / Denaturation 94℃ 30 s 25-35 cycles Anneal 55-65℃ 30 s 25-35 cycles Extend 72℃ 30 s 25-35 cycles Finally extended 72℃ 2 min / Attention:1) In general experiments, if the annealing temperature is 5 ° C lower than the melting temperature Tm of the amplification primer, and the ideal amplification efficiency cannot be achieved, the annealing temperature should be appropriately reduced; When non-specific reactions occur, increase the annealing temperature to optimize the reaction conditions.2) The extension time should be set according to the size of the amplified fragment. The amplification efficiency of Taq DNA Polymerase in this product is 2 kb/min.3) The number of cycles can be set based on the downstream application of the amplification product. If the number of cycles is too small, the amplification amount is insufficient; If there are too many cycles, the probability of mismatches will increase, and non-specific backgrounds will be severe. So, while ensuring product yield, the number of cycles should be minimized as much as possible... Read More | Biochemical Test:SDS-PAGE (purity > 80%); Western blot with patient sample.Calculated Isoelectric Point:pH 8.38 | 1、Product attributeReaction time：short (up to 20 minutes) at 20-37°CLot-to-lot variation：<5%Boiling point : 100℃pH-Value (at 20 °C): 3.5-4.0Density (20℃) : 1.0111 g/cm³Appearance: colourless to pale blue liquidOdour: odourlessRecommend Incubation 1、Product attributeReaction time：short (up to 20 minutes) at 20-37°CLot-to-lot variation：<5%Boiling point : 100℃pH-Value (at 20 °C): 3.5-4.0Density (20℃) : 1.0111 g/cm³Appearance: colourless to pale blue liquidOdour: odourlessRecommend Incubation temperature: 20-37 °C2、Requirements for storage rooms and vessels1.Keep container tightly closed.2.Keep cool. protected from light3.Keep/Store only in original container.4.Never return spills in original containers for reuse.5. Keep away from: Food and feeding stuffs3、It is a ready-to-use, labelling-free TMB-substrate solution.4、Biosafety informationThis mixture is not classified as hazardous in accordance with Regulation (EC) No 1272/2008；5、Advantage1. Very high absorbance yield2. Very low background signals3. Certified long-term stability4. Regeneration following light exposure... Read More |