| Description | CENPU Human Pre-designed siRNA Set A contains three designed siRNAs for CENPU gene (Human), as well as a negative control, a positive control, and a FAM-labeled negative control. Components CENPU siRNA-1: 5 nmol (HPLC) CENPU siRNA-2: 5 nmol (HPLC) CENPU siRNA-3: 5 nmol (HPLC) siRNA Negative Control:CENPU Human Pre-designed siRNA Set A contains three designed siRNAs for CENPU gene (Human), as well as a negative control, a positive control, and a FAM-labeled negative control. Components CENPU siRNA-1: 5 nmol (HPLC) CENPU siRNA-2: 5 nmol (HPLC) CENPU siRNA-3: 5 nmol (HPLC) siRNA Negative Control: 5 nmol (HPLC) FAM-labeled siRNA Negative Control: 5 nmol (HPLC) GAPDH siRNA Positive Control:5 nmol (HPLC)... Read More | Amine-Reactive probe which passively diffuse into cells and it is nonfluorescent until the acetate groups are cleaved by intracellular esterases to yield the highly fluorescent, amine-reactive fluorophore. Upon reaction with amine-containing residues of intracellular proteins, these probes form dye Amine-Reactive probe which passively diffuse into cells and it is nonfluorescent until the acetate groups are cleaved by intracellular esterases to yield the highly fluorescent, amine-reactive fluorophore. Upon reaction with amine-containing residues of intracellular proteins, these probes form dye protein adducts that are well retained in cells as they move and divide during embryonic development.A Non-fluorescent cell permeant amine-reactive probe for long term tracing of cell... Read More | EPOCROSTM is a reactive polymer with an oxazoline group on the side chain and is used as a cross-linking agent for water-based resins. Among the water-based polymers developed to address environmental issues and the increasing use of water-based products due to VOC regulations and desolventing, the EPOCROSTM is a reactive polymer with an oxazoline group on the side chain and is used as a cross-linking agent for water-based resins. Among the water-based polymers developed to address environmental issues and the increasing use of water-based products due to VOC regulations and desolventing, the EPOCROSTM WS series is a “water-soluble type” with the following structure.Features and PropertiesHigher reactivity than water-based epoxy, melamine, blocked isocyanateVOC free (EPOCROS™ WS-300 and EPOCROS™ WS-700)High crosslinking density with a small amount addedOne-pack type with long usage timeImproves water resistance, solvent resistance, heat resistance, and the strength of films, etc.Adhesion-imparting possible to PET, OPP, PVC, etc.Fast dryingLow toxicity (Ames Test: Negative, Primary Skin Irritation Test: No irritation)WS Series Product LineupApplicationsNonwoven fabric bindersPigment printingCoatings (metals, films, leather)Paint and coatings, Primers (plastics, building materials, vehicles)AdhesivesMethodASSAY for Product Code DILW:One unit equals a decrease in absorbance of 1.0 per minute at 25°C at pH 7.5 with 2,6-dichlorophenolindophenol as the chromogen.Reagents0.2 M Tris⋅HCl buffer, pH 7.50.006 M NADH. Prepare fresh daily.0.0012 M Dichlorophenolindophenol (DCPIP) Prepare fresh daily.EnzymePrepare a 10 mg/ml solution of enzyme in 0.2 M Tris⋅HCl, pH 7.5.Dilute further immediately before use to give ΔA/min of 0.15-0.20.ProcedureAdjust spectrophotometer to 600 nm and 25°C.Pipette into cuvettes as follows:Mix quickly and measure the decrease in absorbance at 600 nm for 2-3 minutes.Determine the ΔA/min. from the initial linear portion of the curve. (Use portion of curve from t=0 to t=1 minute; the rate is linear for 1/2 to 1 minute.)Calculation... Read More | Product introduction：Used to isolate lymphocytes from human organsMatters needing attention：1. samples, reagents and experimental environment in the whole process shall be carried out at 20 ± 2 ℃. In order to obtain the best experimental results, it is best to carry out the Product introduction：Used to isolate lymphocytes from human organsMatters needing attention：1. samples, reagents and experimental environment in the whole process shall be carried out at 20 ± 2 ℃. In order to obtain the best experimental results, it is best to carry out the experiment within 2 h of sampling. The longer the sample is stored, the worse the cell separation effect is. The separation effect is even worse after the sample is placed for more than 6 h, or even cannot achieve the purpose of separation. 2. in this experiment, it is better not to use plastic products with high polymerization materials (such as polystyrene), but use non-static, low static ionization heart tubes and glass products without alkali treatment, because the electrostatic effect will lead to cell adhesion, and the surface of alkali treated glass will become rough, which will affect the effect of cell separation. 3. aspirating too many lymphocyte layers and separation liquid layers will cause the granulocytes at the junction of separation liquid to be aspirated, thus increasing the number of mixed granulocytes. 4. when the amount of separating solution is greater than that of tissue single cell suspension sample, the separation effect is better.Scope of application：Lymphocyte isolation... Read More | Telomerase-IN-3 is a telomerase inhibitor, which directly targets hTERT promoter activity. hTERT is the key component for maintenance of telomerase activity.Form:Solid |