| Description | BICRA Human Pre-designed siRNA Set A contains three designed siRNAs for BICRA gene (Human), as well as a negative control, a positive control, and a FAM-labeled negative control. Components BICRA siRNA-1: 5 nmol (HPLC) BICRA siRNA-2: 5 nmol (HPLC) BICRA siRNA-3: 5 nmol (HPLC) siRNA Negative Control:BICRA Human Pre-designed siRNA Set A contains three designed siRNAs for BICRA gene (Human), as well as a negative control, a positive control, and a FAM-labeled negative control. Components BICRA siRNA-1: 5 nmol (HPLC) BICRA siRNA-2: 5 nmol (HPLC) BICRA siRNA-3: 5 nmol (HPLC) siRNA Negative Control: 5 nmol (HPLC) FAM-labeled siRNA Negative Control: 5 nmol (HPLC) GAPDH siRNA Positive Control:5 nmol (HPLC)... Read More | Protein Purity>97% by SDS-PAGEExtinction Coeff.A280 nm = 0.41 at 1.0 mg/mlMolecular Weight10,400 Da (single chain)General DescriptionNatural human C5a is prepared from human C5 protein by cleavage of the peptide bond between C5a and C5b by the human C5 convertase. C5a is a naturally glycosylated Protein Purity>97% by SDS-PAGEExtinction Coeff.A280 nm = 0.41 at 1.0 mg/mlMolecular Weight10,400 Da (single chain)General DescriptionNatural human C5a is prepared from human C5 protein by cleavage of the peptide bond between C5a and C5b by the human C5 convertase. C5a is a naturally glycosylated polypeptide containing 74 amino acids with a molecular weight of approx. 10,400 daltons. Itcontains 25% carbohydrate attached to a single Asn residue at position 64. This carbohydrate is of variable structure leading to a broad distribution of MW upon analysis by mass spectroscopy. C5a is the most potent anaplylatoxin (compared to C3a and C4a). Its biological properties include being strongly chemotactic for neutrophils (PMN), causing smooth muscle contraction, increasing vascular permeability, causing histamine and TNFalpha release, and causing lysosomal degranulation of immune cells. C5a acts through the C5a Receptor (C5aR, CD88, a G-protein coupled receptor) on PMN, monocytes, alveolar macrophages, and mast cells. A second receptor of unknown function (C5L2, gpr77) has been identified. Due to the widespread expression of C5a receptors and the results from C5aR KO mice it is believed that C5a and its receptors have many non-immunolgical functions in organ development, CNS development, neurodegeneration, tissue regeneration and hematopoiesis (Monk, P.N. et al. (2007)).Native versus Recombinant C5aNumerous recombinant forms of C5a are sold by many companies. In side-by-side biological testing, we have found that our native C5a is 10- to 100-fold more active per µg than all but one of these recombinant proteins. Structurally not a single one of the recombinant proteins on the market has the correct amino acid sequence or structure. They have extra amino acids at the N-terminal (such as 6 His tags), different amino acids in the sequence itself (some were produced from the original, but incorrect amino acid sequence), and none possess the 25% carbohydrate at Asn 64. In fact, one recombinant C5a on the market has approximately 30 additional amino acids at the N-terminal end due to the cloning vector used. This is a 40% addition of nonsense structure to the C5a molecule. Both our C5a and our C5adesArg are native proteins produced by the native human C5 convertase. Physical Characteristics & StructureMolecular weight: 10,400 (+ 1,000 due to variable glycosylation)Deglycosylated MW: 8,271 (observed). Calculated monoisotopic mass 8268;Calculated average mass 8273.Isoelectric point: pI = 8.9Carbohydrate content: ~25% carbohydrate (heterogeneous) Amino acid sequence: TLQKKIEEIA AKYKHSVVKK CCYDGACVNNDETCEQRAAR ISLGPRCIKA FTECCVVASQ LRANISHKDM QLGRCAS Number: 80295-54-1MDL Number: MFCD00130842NMRderived structure: FEBS Lett. 238:289-294, 1988; Biochemistry 28:172-185,1989; Biochemistry 29:2895-2905, 1990; Proteins 28:261-267, 1997.FunctionC5a released from C5 by C5 convertases initiates a multitude of inflammatory reactions. C5a causes neutrophils to become adherent to endothelium and to migrate to the site of complement activation by chemotaxis where it stimulates release of PMN granule contents and reactive oxygen species. The biological properties of C5a include being strongly chemotactic for neutrophils (PMN), causing smooth muscle contraction, increasingvascular permeability, causing histamine release, and initiating lysosomal degranulation of a variety of immune cells. C5a acts through the C5a Receptor (C5aR, a G-protein coupled receptor) on PMN, monocytes, alveolar macrophages, dendritic cells, mast cells, glial cells and smooth muscle cells. Rapid release of C5a and other anaphylatoxins can cause systemic effects as well as local changes. Anaphylatic shock is a generalized circulatory collapse similar to that caused by an allergic reaction and is caused by C3a and C5a which are generally released together. AssaysThe multitude of biological functions of C5a has resulted in the use of many different assay systems (Dodds, A.W. and Sim, R.B. (1997)). The most typical biological assays being smooth muscle contraction assays using guinea pig ileum, chemotaxis assays using neutrophils or granule-release assays using human PMN or similar cell lines. Granule release is generally followed by measuring the release of myeloperoxidase. In addition, assays have been described that measure ATP release from guinea pig platelets, serotonin relaease from guinea pig platelets, N-acetyl-beta-D-glucosamidase release from differentiated U937 cells and calcium release from differentiated U937 cells. These assays have been described in detail (Dodds, A.W. and Sim, R.B. (1997)). Functional responses have been detected in the sub-picomolar concentration range for purified human C5a (Gerard, C. et al. (1981); Hugli, T.E. et al. (1981)).ELISA kits for the assay of C5a levels (or more correctly C5a desArg levels) in blood and other fluids are sold by many companies. A radioimmunoassay for C5a/C5a desArg is also available. These measurements are useful for detecting complement activation in vivo, but the interpretation of their meaning is complicated by the fact that clearance of the anaphylatoxins is rapid. In vivoThe resting serum concentration has been reported to be approximately 4 nMalthough it is difficult to draw or store blood without 1 to 10 % C5 activation (Watkins, J.(1987)). The presence of EDTA and Futhan in the collection tubes can minimize this background. Full activation of all C5 in blood (75 µg/mL) would result in ~380 nM C5a(~3.9 µg/mL). Due to the extreme sensitivity of many C5a responses, a response can theoretically be initiated by activation of approximately one millionth of the C5 in a local area.RegulationC5a levels are regulated by three processes: formation, inactivation and clearance. The enzymes that cleave C5 and release C5a (collectively called C5 convertases) do so at very slow rates. Operating at Vmax the best enzymes only cleave one C5 every three minutes (Rawal, N. and Pangburn, M.K. (2001)). C5a is “inactivated” by removal of its Cterminal arginine amino acid. The product C5a desArg (or C5a without the C-terminal arginine) is produced by the action of the plasma enzyme carboxypeptidase N (Mueller-Ortiz S.L. et al. (2009)). This inactivation is rapid and most C5a is converted to C5a desArg within minutes of its formation. “Inactivated” C5a still possesses approx. 1% of its anaphylatoxic and chemotatic activities, but its stimulatory activity is only reduced 10-fold. Thus, C5a desArg retains considerable biological activity even though it is frequently called inactivated C5a. Because of the large number of cells bearing C5a receptors (endothelial, immune, smooth muscle, neuronal, etc.) the capture, internalization and digestion of C5a results in its rapid removal from circulation.DeficienciesA deficiency of C5 or a deficiency of the enzymes that cleave C5 to generate C5a result in the absence of C5a. There are no known complete deficiencies of C5 convertases. Examples of C5 deficient humans and mice exist. In fact, many laboratory mouse strains in common use were shown to have been bred with a deficiency of C5 (A/HeJ, AKR/J, DBA/2J, NZB/B1NJ, SWR/J, and B10.D2/nSnJ). The lack of C5 prevents formation of the membrane attack complex of complement and precludes formation of C5a. Humans lacking C5 are susceptible to repeated infections from a wide variety of organisms, primarily gramnegative bacteria. Meningococcal and gonococcal neisserial infections are especially problematic. The degree to which pathologies associated with C5 deficiency are due to the lack of C5 or the absence of C5a is unclear, but information on this is being acquired from receptor knock-out animals.DiseasesSee Deficiencies above.Precautions/Toxicity/HazardsThis protein is purified from human serum and therefore precautions appropriate for handling any blood-derived product must be used even though the source was shown by certified tests to be negative for HBsAg, HTLV-I/II, STS, and for antibodies to HCV, HIV-1 and HIV-II.Injection can cause anaphylatic shock which is a generalized circulatory collapse similar to that caused by an allergic reaction.Hazard Code: B WGK Germany 3... Read More | Ganglioside GT1b is a brain ganglioside. It is composed of a neutral tetra-saccharide core, with one or two sialic acid on the internal galactose and an extra sialic acid on the non-reducing terminal of galactose | Products contentN665730Component24 T96 TStorageN665730ATPS V50 144 µL576 µL-20℃. Avoid freeze/thaw cycle.N665730B5×FA Reaction Buffer144 µL576 µL-20℃. Avoid freeze/thaw cycle.N665730C2×HiFidelity PCR Mix600 µL2×1.2 mL-20℃. Avoid freeze/thaw Products contentN665730Component24 T96 TStorageN665730ATPS V50 144 µL576 µL-20℃. Avoid freeze/thaw cycle.N665730B5×FA Reaction Buffer144 µL576 µL-20℃. Avoid freeze/thaw cycle.N665730C2×HiFidelity PCR Mix600 µL2×1.2 mL-20℃. Avoid freeze/thaw cycle.N665730DPPM48 µL192 µL-20℃. Avoid freeze/thaw cycle.* This kit is suitable for human genomic DNA library construction with a starting template DNA input of 50 ng. We also have transposase library construction kits for human genomic DNA starting at 5 ng and 1 ng, so it is recommended to use different kits for different starting amounts of DNA in order to obtain higher quality libraries. Products IntroductionThis kit is developed for Illumina's high-throughput sequencing platform and provides the enzyme premix system and reaction buffer for genomic DNA library construction, including all components except PCR primers. Compared with the traditional library construction kits, this kit adopts the new transposase method for library construction, which can complete DNA fragmentation, end repair and junction reaction in one simple enzymatic reaction, significantly reducing the amount of template, reducing the number of experimental steps, and shortening the time of library construction; it adopts the high-fidelity DNA polymerase for library enrichment, and the preference-free PCR amplification can expand the coverage area of the sequence, which can be used for efficient and effective sequencing. The use of high-fidelity DNA polymerase for library enrichment and preference-free PCR amplification broadens the coverage area of the sequence and enables efficient preparation of DNA libraries for Illumina's second-generation sequencing platform. The kit is suitable for DNA libraries with a starting template of 50 ng, and all reagents in the kit have been subjected to strict quality control and functional validation to maximize the stability and reproducibility of library construction. Product Features ● DNA fragmentation and junction ligation in one step.● Ultra-fidelity amplification minimizes amplification-preferred steps.Provide your own instruments, kits and consumables1. Magnetic frame: DynaMagTM-2 is recommended.2. DNA purification and recovery kit: It is recommended to use DNA purification and recovery kit by magnetic bead method.3. Library PCR primer kits: transposase method for second-generation sequencing multi-sample primer kits are recommended. 4. Anhydrous ethanol, deionized water (pH between 7.0 and 8.0).5. Reaction tubes: It is recommended to use low adsorption PCR tubes and 1.5 ml centrifuge tubes. Tips: It is recommended to use high quality filter tips to prevent contamination of kits and library samples. Pre-experiment Preparation and Important Notes1. Avoid repeated freezing and thawing of reagents.2. PCR products are easily contaminated due to improper operation, resulting in inaccurate results. It is recommended to isolate the PCR reaction system preparation area from the PCR product purification area, and to use special pipettes to clean the experimental areas at regular intervals.3. Bead purification: the beads should be equilibrated to room temperature before use, all operations on the beads should be carried out at room temperature, 80% ethanol should be dispensed freshly, the beads should be rinsed and dried until the surface is free of liquid reflections and has a frosted appearance, insufficient drying of the beads will cause ethanol residue that will affect the subsequent experiments, and over-drying of the beads will affect the efficiency of DNA recovery.4. The kit is suitable for human genomic DNA library construction, if the DNA sample is a PCR product, it should be ensured that its length>.500 bp, since transposases do not work on DNA ends, it is recommended to extend the PCR product by 50-100 bp at each end of the PCR product to avoid low coverage of the ends for sequencing.Sample PreparationDNA purity requirements: A260/A280 = 1.8-2.0. Sample DNA: dissolve in ultrapure water. DNA Quantification: Too much or too little DNA will affect the quality of the library. It is recommended to use Nano to test the purity of the genomic DNA and then use Qubit to test the concentration of the genome (do not use any absorbance-based assay for template quantification).Schematic diagram of DNA banking processprocedureDNA fragmentation, junction reaction1. Add the following reagents to a 200 µl PCR tube: 2. Mix by gently blowing with a pipette and centrifuge briefly so that all components are collected at the bottom of the tube.3. Place the above PCR tubes in the PCR instrument with the hot cap on and program the reaction as follows:DNA should be purified immediately after the fragmentation reaction has been performed and the transposase is still in a high state of activity.to prevent smaller library fragments due to DNA over-fragmentation. Purification of fragmentation productsWe recommend the use of the Century Magnetic Bead Method DNA Purification and Recovery Kit.1. CMPure should be equilibrated at room temperature for 30 min after shaking and mixing before use.2. Add 50 µl of magnetic beads equilibrated to room temperature to the fragmentation product, vortex and shake for 5 seconds, then let stand at room temperature for 5 minutes.3. Centrifuge briefly, place the tube on a magnetic rack to separate the beads from the supernatant solution until the solution is clear (approximately 3-5 minutes), carefully aspirate the supernatant and discard, avoiding contact with the beads that have bound the target DNA. Note: Do not discard the beads.4. Continue to keep the centrifuge tube fixed on a magnetic rack and add 200 µl of freshly prepared 80% ethanol to the centrifuge tube and allow to stand at room temperature for 30 seconds, carefully discarding the supernatant.Note: When adding ethanol, the liquid must not be blown directly onto the beads.5. Repeat step 4.6. Keep the centrifuge tube fixed on a magnetic rack and leave to dry at room temperature until the surface of the beads is slightly cracked, then add 23 µlddH2O to solubilize.Note: Do not over-dry the beads as this may affect the elution efficiency.7. Remove the tube from the magnetic rack, vortex to completely resuspend the beads, and allow to stand at room temperature for 5 minutes. Centrifuge briefly, place the tube on the magnetic rack until the solution is clear, and transfer 21 µl of supernatant to a new 200 µl PCR tube.PCR amplification Add the following reagents to the 200 µl PCR tube: Mix by gently blowing with a pipette and centrifuge briefly so that all components are collected at the bottom of the tube.3. Place the above PCR tubes in the PCR instrument with the hot cap on and program the reaction as follows:Selective recovery of library DNA fragmentsIt is recommended to use CombiVision Magnetic Beads DNA Purification and Recovery Kit for selective recovery of DNA fragments. When different sizes of DNA fragments are required, the amount of magnetic beads to be used is different, please refer to the attached table for the specific amount of magnetic beads to be used (if other brands of magnetic beads are used, you need to find out the optimal amount of magnetic beads to be used on your own).Note: Amplification products can also be fragment length sorted and purified using the Gum Recovery Kit. If there is no special requirement for library length distribution, the amplification products can also be purified without selective recovery of DNA fragments as described on page 6 of the manual.1. CMPure should be equilibrated at room temperature for 30 min after shaking and mixing before use.2. Transfer the PCR product to a 1.5 ml centrifuge tube, rehydrate to 100 µl and add several volumes of magnetic beads equilibrated to room temperature, vortex for 5 seconds and let stand at room temperature for 5 minutes.3. Centrifuge briefly, place the tube on a magnetic rack to separate the beads from the supernatant until the solution is clear, and carefully aspirate the supernatant and transfer it to a new 1.5 ml centrifuge tube.Note: Do not discard the top clear.4. Add several volumes of magnetic beads to the supernatant, vortex and shake for 5 seconds, then let stand at room temperature for 5 minutes.5. Centrifuge briefly, place the tube on a magnetic rack to separate the beads from the supernatant until the solution is clear, carefully aspirate the supernatant and discard it, avoiding contact with the beads that have bound the target DNA.Note: Do not discard the beads.6. Continue to keep the centrifuge tube fixed on a magnetic rack and add 200 µl of freshly prepared 80% ethanol to the tube and allow to stand at room temperature for 30 seconds, carefully discarding the supernatant.Note: When adding ethanol, the liquid must not be blown directly onto the beads.7. Repeat step 6 once.8. Keep the centrifuge tube fixed on a magnetic rack and leave to dry at room temperature until the surface of the beads is slightly cracked, add 20 µl of ddH2O to solubilize.Note: Do not over-dry the beads as this may affect the elution efficiency.9. Remove the centrifuge tube from the magnetic rack, vortex and oscillate to completely resuspend the beads, and let stand at room temperature for 5 minutes. Leave brieflycentrifuge, place the tube on a magnetic rack until the solution is clear, and transfer the supernatant solution to a new centrifuge tube. Table: Suggested amount of magnetic beads for different segment selection recoveryLibrary DNA fragment purificationWe recommend the use of the Century Magnetic Bead Method DNA Purification and Recovery Kit.1. CMPure should be equilibrated at room temperature for 30 min after shaking and mixing before use.2. 50 µl of magnetic beads equilibrated to room temperature were added to the PCR product, vortexed and shaken for 5 seconds, and then left to stand at room temperature for 5 minutes.3. Centrifuge briefly, place the tube on a magnetic rack to separate the beads from the supernatant solution until the solution is clear (approximately 3-5 minutes), carefully aspirate the supernatant and discard it, avoiding contact with the beads that have bound the target DNA. Note: Do not discard the beads.4. Continue to keep the centrifuge tube fixed on a magnetic rack and add 200 µl of freshly prepared 80% ethanol to the centrifuge tube and allow to stand at room temperature for 30 seconds, carefully discarding the supernatant.Note: When adding ethanol, the liquid must not be blown directly onto the beads.5. Repeat step 4.6. Keep the centrifuge tube fixed on a magnetic rack and leave to dry at room temperature until the surface of the beads is slightly cracked, add 25 µl of ddH2O to solubilize.Note: Do not over-dry the beads as this may affect the elution efficiency.7. Remove the tube from the magnetic rack, vortex to completely resuspend the beads, and allow to stand at room temperature for 5 minutes. Centrifuge briefly, place the tube on the magnetic rack until the solution is clear, and transfer the supernatant solution to a new tube.Library quality controlDetermination of library concentrationIn order to obtain high-quality sequencing results, accurate quantification of DNA libraries is required, and the first recommendation is to use Real-timePCR methods are used for absolute quantification of DNA libraries. Additionally, fluorescent dye methods such as the Qubit method or the fluorescent dye picogreen method can be used; do not use quantification methods based on absorbance measurements here. The following approximate formula can be used to convert the molar concentration of the DNA library. Average total length of librariesApproximate conversion formula Library fragment distributionThe prepared DNA libraries can be detected by agarose gel electrophoresis or Agilent 2100 Bioanalyzer.Range of segment length distributions... Read More | BackgroundStreptavidin is a tetrameric bacterial protein isolated from Streptomyces avidinii providing 4 high-affinity biotin binding sites. Streptavidin homo-tetramers have an extraordinarily high affinity for biotin. With a dissociation constant on the order of ≈10⁻¹⁴ mol/L,BackgroundStreptavidin is a tetrameric bacterial protein isolated from Streptomyces avidinii providing 4 high-affinity biotin binding sites. Streptavidin homo-tetramers have an extraordinarily high affinity for biotin. With a dissociation constant on the order of ≈10⁻¹⁴ mol/L, the binding of biotin to streptavidin is one of the strongest non-covalent interactions known in nature. Unlike egg-white avidin, which has a net positive charge at neutral pH and contains about 7% carbohydrate, streptavidin has almost no net charge at neutral pH, does not contain carbohydrate, and exhibits lower non-specific background. Streptavidin conjugates are widely used together with a conjugate of biotin for specific detection of a variety of proteins, protein motifs, nucleic acids and other molecules. This FITC-streptavidin conjugate was prepared by highly purified Streptavidin and free FITC was removed. Streptavidin (FITC) is a useful second-step reagent for the indirect immunofluorescent staining of cells in combination with biotinylated primary antibodies for flow cytometric analysis. Excitation at 488nm light leads to a fluorescence emission maximum of 520 nm.Recommended Usage：Every lot of Streptavidin-FITC is tested by flow cytometry using biotinylated primary antibodies. From this testing it is recommended that between 0.02 and 0.25 µg of streptavidin be used per 106 cells in a 100 µl staining volume... Read More |