| Description | GPR35 Human Pre-designed siRNA Set A contains three designed siRNAs for GPR35 gene (Human), as well as a negative control, a positive control, and a FAM-labeled negative control. Components GPR35 siRNA-1: 5 nmol (HPLC) GPR35 siRNA-2: 5 nmol (HPLC) GPR35 siRNA-3: 5 nmol (HPLC) siRNA Negative Control:GPR35 Human Pre-designed siRNA Set A contains three designed siRNAs for GPR35 gene (Human), as well as a negative control, a positive control, and a FAM-labeled negative control. Components GPR35 siRNA-1: 5 nmol (HPLC) GPR35 siRNA-2: 5 nmol (HPLC) GPR35 siRNA-3: 5 nmol (HPLC) siRNA Negative Control: 5 nmol (HPLC) FAM-labeled siRNA Negative Control: 5 nmol (HPLC) GAPDH siRNA Positive Control:5 nmol (HPLC)... Read More | Product introduction：Aladdin ® SE is a kind of fluorescent dye with amino reactive activity. The SE group of these dyes can react with the amino group to produce a stable amide bond. Compared with other similar dyes on the market, aladdin ® is a new generation of fluorescent dyes Product introduction：Aladdin ® SE is a kind of fluorescent dye with amino reactive activity. The SE group of these dyes can react with the amino group to produce a stable amide bond. Compared with other similar dyes on the market, aladdin ® is a new generation of fluorescent dyes with stronger stability, better water solubility and better fluorescence intensity. Product parameters： Absmax/Em(nm)：648/664；Absmax/Em(nm)：0.03；Extinction coefficient(ε)：240000；Optimal DOL(IgG)：3-6； Usage:1. Experimental materials(1) IgG: IgG must not contain amine chemicals that can react with dyes, such as amino acids, Tris, BSA, gelatin, etc. If IgG contains such chemicals, PBS buffer with pH~7.4 should be used for pre dialysis treatment. The presence of azide compounds does not affect the labeling reaction.(2) Anhydrous DMSO(3) NaHCO3(4) Sephadex gel G-25 dialysis column(5) PBS buffer (pH~7.4)(6) NaN3(7) BSA2. Marking methods and steps(1) Prepare to label antibodiesDilute the antibody with 0.1 M NaHCO3 solution (pH~8.3) to a final concentration of 2.5 mg/mL. If the product is pre diluted with phosphate buffer, such as PBS buffer (without amino compounds), approximately 1/10 volume of 1M NaHCO3 mother liquor can be directly added to the buffer to achieve a final NaHCO3 concentration of 0.1 M.Note: When the protein concentration is 2.5 mg/mL, the labeling efficiency is approximately 35%. Protein concentrations below 2.5 mg/mL can also be used for labeling, but the labeling efficiency will decrease. When the protein concentration is higher than 5 mg/mL, the labeling efficiency may be higher. Due to differences in buffer and protein purity, more precise labeling efficiency is determined by practical operating conditions. If the protein concentration is too low, it can be concentrated by ultrafiltration.(2) Prepare dye storage solutionPreheat one tube at room temperature µ YF of Mole ® SE, add 0.1 mL of anhydrous DMSO to the tube, thoroughly vortex dissolve the dye, and prepare a dye storage solution with a concentration of 10 mM. If a trace amount of protein is used for labeling reactions, the dye needs to be diluted to a lower concentration.Note: a The remaining dye storage solution should be stored at a low temperature of -20 ℃ for future use. If anhydrous DMSO is used to prepare dye storage solution, the dye can be stored for at least one month.b. Dyes can also be prepared with deionized water, but due to the slow hydrolysis of dyes in water, it is best to prepare water based storage solutions for immediate use.(3) Mark reaction stepsa. Stir or vortex the protein solution, gradually adding 15-25 drops µ L dye storage solution (10 mM), with a molar ratio of dye/protein in the range of 9:1 to 15:1. YF ® Please refer to the table above for the range of DOL (number of dyes bound to each protein molecule) for SE labeled IgG antibodies.b. Stir the reaction at room temperature for 1 hour, and for trace labeling, shake and incubate on a shaker for 1 hour.Note: At the same time of the binding reaction, proceed to step 2 (4) to balance the dextran gel G-25 dialysis column.(4) Isolation of marker proteins from reaction solutiona. PBS buffer (pH~7.4) was used to balance the dextran gel G-25 dialysis column (10 mm × 300 mm).b. Add the reaction solution from step 3 (b) to the column and elute with 1 x PBS buffer.The first washed out chromophore is a dye protein complex.Note: a For small-scale labeling reactions, in order to avoid excessive dilution of the product, ultrafiltration devices can be used to remove free dyes from the complex.b. After the binding reaction is completed, if the dye protein complex is not separated in time, 50 can be added µ Terminate the reaction with L 1M lysine. In most cases, this operation is not necessary because the remaining unreacted dyes have been fully hydrolyzed at the end of the reaction.3. Determine DOL(1) The determination of protein concentration and antibody concentration can be calculated using the following formula:C (mg/mL)={[A280- (Amax x x Cf)]/1.4} x dilution factor;a. C refers to the concentration of antibodies collected in the experiment;b. Dilution factor refers to the dilution factor used in photometric measurements;c. A280 and Amax refer to the absorbance at 280 nm and the absorbance at the absorption wavelength, respectively;d. Cf is the correction factor, YF ® Please refer to the table above for the Cf value of SE dyes;Note: The protein solution eluted through the column may have a high concentration when used directly for absorbance detection, so it needs to be diluted to approximately 0.1 mg/mL. The dilution factor (i.e. dilution factor) needs to be determined from the initial number of antibodies (e.g. 5 mg) and the overall elution of protein solutionEstimate based on the product.(2) Estimation of DOLDOL is calculated using the following equation:DOL=(Amax x x Mwt x Dilution Factor)/（ ε X C)a. Amax, dilution factor, C value has been clearly defined in 3 (1);b. Mwt refers to the molecular weight of IgG (150000);C. c ε It's YF ® The molar absorption coefficient of SE, refer to the table on the first page;d. Mark YF ® The optimal DOL value for SE IgG antibodies can be found in the table on the first page. Although DOL values may fluctuate, good experimental results can also be achieved.Matters needing attention：1. if the labeled protein needs long-term storage, it is recommended to add 5-10 mg/ml BSA and 0.01-0.03% NaN3 to prevent protein denaturation and microbial breeding. Store at 4 ℃ away from light. If glycerol with a final concentration of 50% is added, it can be stored at -20 ℃. It can be stably stored for more than one year. 2. keep away from light during operation. The mixing speed should be appropriate to avoid bubbles. 3. when installing the chromatographic column, try to make the column body uniform, the column surface flat, and free of bubbles and cracks. 4. pay attention to adding the sample when the column top buffer is tangent to the gel plane. When eluting, add the eluent when the sample is tangent to the gel plane. 5. other factors affecting the labeling efficiency also include temperature, reaction time, pH, the amount of fluorescent dye and protein, etc., which should be controlled. 6. for your safety and health, please wear laboratory clothes and disposable gloves.Scope of application：Protein nucleic acid labeling dye... Read More | This product is a mixture of fast reverse transcription reagents. The 5 x EasyQuick RT MasterMix contains all the reagents required for reverse transcription from RNA templates to cDNA first strand, including EasyQuick RT Reversase, RNase Inhibitor, Random 6 mers, Oligo dT Primer, dNTP, EQ-RT BufferThis product is a mixture of fast reverse transcription reagents. The 5 x EasyQuick RT MasterMix contains all the reagents required for reverse transcription from RNA templates to cDNA first strand, including EasyQuick RT Reversase, RNase Inhibitor, Random 6 mers, Oligo dT Primer, dNTP, EQ-RT Buffer, etc. The reverse transcription efficiency of this product is high, and it can perform a good reverse transcription reaction on a small amount of RNA templates. The fluorescence quantitative template cDNA first strand synthesis can be completed in 15 minutes. This reagent kit is very convenient and fast to operate, and only RNA templates and water need to be added for reverse transcription reaction, making it particularly suitable for high-throughput detection.E665905Component200 TStorageE665905A5×EasyQuick RT MasterMix 400 µL-20℃. Avoid freeze/thaw cycle.E665905BRNase-Free Water 2×1 mL-20℃. Avoid freeze/thaw cycle. Product features1. Convenience: The ready to use reverse transcription Mix only requires the addition of RNA templates and water to initiate the reaction.2. Fast: Complete cDNA first strand synthesis in 15 minutes.3. High reverse transcription efficiency: The reverse transcription efficiency is above 90%.4. High sensitivity: PG level templates can also obtain high-quality cDNA.5. Read through complex templates: templates with high GC content and complex secondary structures.Matters needing attention1. During the operation, RNase contamination should be avoided to prevent RNA degradation or cross contamination during experiments. It is recommended that operators wear masks and disposable gloves, frequently change gloves, and use specialized instruments and consumables.2. The reverse transcription system is prepared on ice for operation to prevent RNA degradation. The MasterMix of the reagent kit should be stored at -20 ℃ as soon as possible after use, and repeated freeze-thaw should be avoided as much as possible.3.10 µ The reaction system can be used up to 1 µ G Total RNA, if the amount of template RNA is greater than 1 µ g. Please expand the reaction system proportionally.4. For RNA templates with complex secondary structures, it is recommended to incubate the template RNA at 65 ℃ for 5 minutes on ice before proceeding with the next step, followed by brief centrifugation.Operation steps1. Thaw the template RNA on ice; After thawing the components of the reagent kit at room temperature, immediately place them on ice. Before use, vortex shake and mix each solution, and centrifuge briefly before use.2. Prepare the reaction system according to the following table (please prepare the reaction solution on ice), vortex shake and mix well, briefly centrifuge, and collect the solution on the tube wall to the bottom of the tube. Reagent 10 µl Reaction system Final concentration RNA Template X µl 1 pg～0.5 µg ¹⁾ 5×EasyQuick RT MasterMix ²⁾ 2 µl 1× RNase-Free Water up to 10 µl /Attention:1) If the total RNA content is greater than 1 µ g, please expand the reaction system proportionally.2) 5 x EasyQuick RT MasterMix contains Oligo (dT), Random Prime, RNase Inhibitor, dNTP Mixture, EQ-RT Buffer, etc. 3. Incubate at 37 ℃ for 15 minutes. 4. Incubate at 85 ℃ for 5 seconds to inactivate reverse transcriptase.5. After a brief centrifugation, place it on ice for subsequent experiments. If it needs to be stored for a long time, please place it at -20 ℃... Read More | 1、Product attributeShelf life: 24 monthsReaction time：long (up to 45 minutes) at 20-37°CLot-to-lot variation：<10%Boiling point : 100℃pH-Value (at 20 °C): 9.0-9.8 Density (20℃) : 1.0302 g/cm³Water solubility: easily solubleAppearance: colourless to 1、Product attributeShelf life: 24 monthsReaction time：long (up to 45 minutes) at 20-37°CLot-to-lot variation：<10%Boiling point : 100℃pH-Value (at 20 °C): 9.0-9.8 Density (20℃) : 1.0302 g/cm³Water solubility: easily solubleAppearance: colourless to light yellow liquidOdour: odourlessIncubation temperature: 20-37 °CLight sensitiveHeat sensitive 2、Requirements for storage rooms and vessels1.Keep container tightly closed.2.Keep cool. protected from light3. Do not store together with: Oxidizing agent. 4. Contaminated or leaked out substrate solution from damaged bottles should not be used anymore and has to be destroyed.5. Use isolated containers with some cool bags for transport.6. Spontaneous decay will increase the background. If stored at room temperature, the velocity of the decay will increase. Thus, both storage and transport at room temperature should be avoided. Nevertheless, the activity of the solution is not affected by storage at room temperature. The solution still works beyond the expiry date, but some applications, especially those including visual evaluation, may be hampered by increased background. 3、Effective Components and Principle of FunctionIn different buffer solutions (pH = 9.5), with supplementation if required, the effective componentpara nitrophenyl phosphate (pNPP) is dissolved. Alkaline Phosphatase transfers the phosphate residue to an acceptor. Under alkaline conditions a yellow colour occurs, resulting from the formed nitrophenol. 4、Biosafety informationThis mixture is not classified as hazardous in accordance with Regulation (EC) No 1272/2008； 5、Advantage1. Signal yield comparable to competitor ready-to-use solutions2. Broad measurement range3. Very low background signals4. Very low blank drift during long-term storage (<0.15 AU within 24 months)5. High colour stability after reaction stop with this product and other commonly used stopping solutions 6、Instruction for usageFor bottling consider the following instructions:• Work in a dust free and darkened room.• Keep the solution as cool as possible.• Avoid contact of the solutions with any metal parts• Clean all instruments and vessels very extensively.• Wear powder-free gloves during bottling.• Close the bottles immediately to minimize the influence of light and dust.• Use clean bottles that are impermeable to light made from HDPE or PP. 7、 General Instructions for the Use in Blotting Systems Only qualified laboratory staff, who are familiar with the basics of immunological methods, are allowed to use these solutions.The substrate solutions can be used in qualitative and quantitative ELISA procedures.When using 96-well microtiter plates, adding 100 µL of substrate per well after incubation and washing is recommended. After substrate incubation the reaction can be stopped and the photometric measurement can be carried out. Using higher incubation temperatures (37° C) may shorten the incubation time. The reaction can be stopped by using the special developed solution stop. The use of other commercially available stop solutions cannot safely exclude a further increase of the signal. Addition of a stopping solution does not change the general shape of the spectrum. The unstopped and the stopped solution should be measured at 405 nm and the background correction: should be measured at 620 nm... Read More | Telomerase-IN-3 is a telomerase inhibitor, which directly targets hTERT promoter activity. hTERT is the key component for maintenance of telomerase activity.Form:Solid |