| Description | The PM2.5 particulate matter monitor PCE-RCM 05 is used to continuously measure the particulate matter content at the workplace. The PCE-RCM 05 PM2.5 monitor displays PM2.5 particulate matter as well as temperature and humidity on the display. The measuring range of the PCE-RCM 05 monitor ranges The PM2.5 particulate matter monitor PCE-RCM 05 is used to continuously measure the particulate matter content at the workplace. The PCE-RCM 05 PM2.5 monitor displays PM2.5 particulate matter as well as temperature and humidity on the display. The measuring range of the PCE-RCM 05 monitor ranges from 0 ... 500 µg / m³ PM2.5. This makes the PM2.5 meter an optimal test instrument to constantly have an overview of the fine dust content. Below the large measured value display of the PM2.5 content, the PM2.5 monitor provides quick information about the air quality with the aid of pictograms.
The PCE-RCM 05 fine dust monitor is powered by a rechargeable battery. The LC display is illuminated and easy to read from any angle, for example when the meter is on a desk. In addition to the standard white lighting, the PM2.5 monitor switches the lighting to red in the event of an alarm.... Read More | The Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, asThe Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, as well as coaxial cables, such as those used in TV, antenna, and surveillance systems.
Testing is carried out using a two-part system consisting of a main unit and a remote unit, which also allows permanently installed cables to be tested reliably. The most important test procedures include continuity testing of the conductors (pins 1–8), wiring testing to check the correct assignment of the wire pairs, and the detection of short circuits, wiring faults, and split-pair faults. In addition, the shielding of shielded cables is checked. The test range covers cable lengths of up to 305 m, whilst the minimum cable length for split-pair detection is approximately 0.5 m.
Our Cable Detector operates using test signals transmitted between the main unit and the remote unit. The results are displayed via LED indicators. Steady LEDs indicate correct wiring, whilst flashing LEDs indicate faults in the respective wire pairs. Additional status LEDs indicate the type of fault, such as short circuit, miswiring, reversal, or split pair.
The Cable Detector is used in network technology, building cabling, and in IT and communications installations, and is designed for electricians, network technicians, and service technicians to quickly test cable runs.... Read More | The Clamp Meter is a multifunctional meter for the precise measurement of alternating and direct voltage as well as alternating and direct current that can be measured without direct contact to the line. The Clamp Meter is suitable for measuring resistance, temperature, diodes, continuity, The Clamp Meter is a multifunctional meter for the precise measurement of alternating and direct voltage as well as alternating and direct current that can be measured without direct contact to the line. The Clamp Meter is suitable for measuring resistance, temperature, diodes, continuity, frequencies and capacitance and is particularly useful for diagnosing electrical and electronic components.
For maximum measurement accuracy, the Clamp Meter supports True RMS for non-sinusoidal waveforms and a Low Impedance (LoZ) function to reduce interference. The non-contact voltage test enables reliable detection of voltages in cables and sockets.
The 2-inch LC display ensures clear readability, even under poor lighting conditions and an integrated LED torch makes it easier to work in dark environments. The device also offers automatic and manual measurement range selection, allowing it to be flexibly adapted to different measuring situations. The device also has a practical zero key which enables accurate measurement of low currents, especially when measuring direct current (DC) and ensures the compensation of deviations of the output value. Other functions include overload protection, data hold, min, max and an automatic power-off after 15 minutes to conserve battery life. The power-off can also be deactivated for longer measurements.
Compact and easy to use, the Clamp Meter is ideal for electrical installations, maintenance work and use in automation technology. It enables safe and efficient measurements, often without direct intervention in the circuit.... Read More | Our robust socket square inserts are specially designed for use with impact wrenches and are ideal for demanding bolting applications. The range covers thread sizes from M16 to M48 and offers the right wrench sizes for a wide variety of applications.
These high-quality robust socket square inserts Our robust socket square inserts are specially designed for use with impact wrenches and are ideal for demanding bolting applications. The range covers thread sizes from M16 to M48 and offers the right wrench sizes for a wide variety of applications.
These high-quality robust socket square inserts impress with their high load-bearing capacity, precise fit, and long service life – perfect for professional use in industry and assembly.... Read More | The Material Tester is a high-quality measuring instrument designed for calibrating torque sensors and for the precise measurement of the tightening torque of screws and other fasteners. The Material Tester offers a high accuracy of ±1% within the range of 10% ... 100% of the scale and can be The Material Tester is a high-quality measuring instrument designed for calibrating torque sensors and for the precise measurement of the tightening torque of screws and other fasteners. The Material Tester offers a high accuracy of ±1% within the range of 10% ... 100% of the scale and can be operated in both clockwise and anti-clockwise directions.
The Material Tester supports several operating modes such as Peak Hold, MAX, and real-time measurement. In Peak Hold mode, the maximum value is automatically saved, and the measurement data can be transferred via USB to the software, which also enables a pass/fail evaluation. Tolerance ranges can be set directly on the device, allowing values to be checked quickly. An integrated LED traffic light display shows the measured value at a glance.
The choice between the units Newton-meter (N·m), kilogram-force-centimeter (kgf·cm), and pound-force-inch (lbf·in) enables flexible applications across various industries. With a storage capacity of 2,000 measurement groups and the option of data transfer via USB, the measuring instrument is ideal for use in the mechanical engineering industry and in scientific research facilities.
The Material Tester operates reliably at ambient temperatures of 5 to 40°C / 41 … 104°F and is powered by a 7.2 V NiMH battery, which is optimized for mobile use.... Read More |