| Description | Portable handheld device for monitoring particulate matter (PM) concentrations in the air / 2.5 µm and 10 µm particle sizes / Measures air temperature and relative humidity. Designed to aid in indoor air quality (IAQ) assessments, this dust monitor also measures air temperature and relative humidityPortable handheld device for monitoring particulate matter (PM) concentrations in the air / 2.5 µm and 10 µm particle sizes / Measures air temperature and relative humidity. Designed to aid in indoor air quality (IAQ) assessments, this dust monitor also measures air temperature and relative humidity (RH). The dust monitor can be powered either by the built-in rechargeable battery or the USB port. The USB port also is used to charge the battery. At full charge, the battery provides up to 5 hours of continuous operation or unlimited operation when plugged into a USB power source. The dust monitor displays all measurements simultaneously on the device's 2.4" full-color LCD screen. PM values ??appear the largest in the colors green, yellow, gold, orange, pink and red. This visual color-coding system makes it easy to recognize when PM concentration levels become dangerous, allowing for quick action.... Read More | Our Cable Detector enables the precise detection and localisation of power lines, wooden beams, metals and other objects such as water-filled plastic pipes in walls, floors and ceilings. Thanks to its versatility, it can be used on various surfaces such as wood, wallpaper, plaster, acoustic walls Our Cable Detector enables the precise detection and localisation of power lines, wooden beams, metals and other objects such as water-filled plastic pipes in walls, floors and ceilings. Thanks to its versatility, it can be used on various surfaces such as wood, wallpaper, plaster, acoustic walls and painted walls.
The device is equipped with a 1.9-inch colour LCD display that provides a clear visual representation of the scan results. A signalling system consisting of coloured LEDs, acoustic cues and directional arrows quickly provides precise information about the proximity and position of the detected object. The LED system indicates green for no obstacles, yellow for nearby objects and red for an obstacle directly under the scanner. The Cable Detector has three detection modes: the metal detection mode for identifying metal objects, the wood detection mode for localising wooden beams and the power mode for detecting live wires. In the metal and power line modes, the device displays the signal strength as a percentage. In wood detection mode, the scanner recognises both the exact centre and the edges of wooden beams, allowing their position and size to be precisely determined.
To further improve the accuracy, the sensitivity can be adjusted in three stages so that the detection can be optimally adapted to the respective conditions. An integrated marking hole makes it possible to mark the drilling site immediately after detection. The Cable Detector also offers automatic calibration, which can be performed on any wall surface. The menu is available in five languages: Russian, English, Portuguese, Japanese as well as Chinese. The automatic switch-off is adjustable and can vary between 5 and 15 minutes or be deactivated completely, depending on requirements. The acoustic signal can also be switched off if required. For reliable and wireless use, the device is equipped with a powerful lithium-ion battery that can be charged quickly and easily via a USB-C port.
With this powerful and user-friendly Cable Detector, obstacles can be reliably detected and construction and renovation work can be carried out safely and efficiently.... Read More | The Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, asThe Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, as well as coaxial cables, such as those used in TV, antenna, and surveillance systems.
Testing is carried out using a two-part system consisting of a main unit and a remote unit, which also allows permanently installed cables to be tested reliably. The most important test procedures include continuity testing of the conductors (pins 1–8), wiring testing to check the correct assignment of the wire pairs, and the detection of short circuits, wiring faults, and split-pair faults. In addition, the shielding of shielded cables is checked. The test range covers cable lengths of up to 305 m, whilst the minimum cable length for split-pair detection is approximately 0.5 m.
Our Cable Detector operates using test signals transmitted between the main unit and the remote unit. The results are displayed via LED indicators. Steady LEDs indicate correct wiring, whilst flashing LEDs indicate faults in the respective wire pairs. Additional status LEDs indicate the type of fault, such as short circuit, miswiring, reversal, or split pair.
The Cable Detector is used in network technology, building cabling, and in IT and communications installations, and is designed for electricians, network technicians, and service technicians to quickly test cable runs.... Read More | The Clamp Meter is a multifunctional meter for the precise measurement of alternating and direct voltage as well as alternating current that can be measured without direct contact to the line. The Clamp Meter is suitable for measuring resistance, temperature, diodes, continuity, frequencies and The Clamp Meter is a multifunctional meter for the precise measurement of alternating and direct voltage as well as alternating current that can be measured without direct contact to the line. The Clamp Meter is suitable for measuring resistance, temperature, diodes, continuity, frequencies and capacitance and is particularly useful for diagnosing electrical and electronic components.
For maximum measurement accuracy, the Clamp Meter supports True RMS for non-sinusoidal waveforms and a Low Impedance (LoZ) function to reduce interference. The non-contact voltage test enables reliable detection of voltages in cables and sockets.
The 2-inch LC display ensures clear readability, even under poor lighting conditions and an integrated LED torch makes it easier to work in dark environments. The device also offers automatic and manual measurement range selection, allowing it to be flexibly adapted to different measuring situations. Other functions include overload protection, data hold, min, max and an automatic power-off after 15 minutes to conserve battery life. The power-off can also be deactivated for longer measurements.
Compact and easy to use, the Clamp Meter is ideal for electrical installations, maintenance work and use in automation technology. It enables safe and efficient measurements, often without direct intervention in the circuit.... Read More | The Material Tester is a high-quality measuring instrument designed for calibrating torque sensors and for the precise measurement of the tightening torque of screws and other fasteners. The Material Tester offers a high accuracy of ±1% within the range of 10% ... 100% of the scale and can be The Material Tester is a high-quality measuring instrument designed for calibrating torque sensors and for the precise measurement of the tightening torque of screws and other fasteners. The Material Tester offers a high accuracy of ±1% within the range of 10% ... 100% of the scale and can be operated in both clockwise and anti-clockwise directions.
The Material Tester supports several operating modes, such as Peak Hold, MAX, and real-time measurement. In Peak Hold mode, the maximum value is automatically stored, and the measurement data can be transferred via USB to the software, which also enables a pass/fail evaluation. Tolerance ranges can be set directly on the device, allowing values to be checked quickly. An integrated LED traffic light display shows the measured value at a glance.
The choice between the units Newton-meter (N·m), kilogram-force-centimeter (kgf·cm), and pound-force-inch (lbf·in) enables flexible applications across various industries. With a storage capacity of 2,000 measurement groups and the option of data transfer via USB, the measuring instrument is ideal for use in the mechanical engineering industry and in scientific research facilities.
The Material Tester operates reliably at ambient temperatures of 5 to 40°C / 41 to 104°F and is powered by a 7.2 V NiMH battery, which is optimized for mobile use.... Read More |