| Description | CO2 analyser with data memory for 5000 measuring points / Temperature, humidity / Export of the saved measurement data in CSV format / Battery and mains operation /
1/4 inch tripod mount / Measuring range (CO²) 0 ... 9999 ppm, (CO) 0 ... 1000 ppm
The CO2 analyser has a measuring range of 0 ... 9999CO2 analyser with data memory for 5000 measuring points / Temperature, humidity / Export of the saved measurement data in CSV format / Battery and mains operation /
1/4 inch tripod mount / Measuring range (CO²) 0 ... 9999 ppm, (CO) 0 ... 1000 ppm
The CO2 analyser has a measuring range of 0 ... 9999 ppm. In addition to the carbon dioxide measurement, the air quality detector also has a carbon monoxide (CO) sensor with a measuring range of 0 ... 1000 ppm and a temperature and humidity sensor. The air quality detector already covers a large range of measuring tasks. The air quality detector is therefore used, for example, in occupational safety to check the climatic conditions in office workplaces.... Read More | Air Quality Meter / Measures temperature and humidity / Visual and audible alarm / USB-C interface / Battery status indicator / Modern design and compact size
A Air Quality Meter is an important device for monitoring indoor air quality. It can be used in a variety of ways - whether in homes, officesAir Quality Meter / Measures temperature and humidity / Visual and audible alarm / USB-C interface / Battery status indicator / Modern design and compact size
A Air Quality Meter is an important device for monitoring indoor air quality. It can be used in a variety of ways - whether in homes, offices, workshops, schools or public facilities. The detector reliably measures the CO content in the air and makes it possible to recognize critical concentrations at an early stage and act accordingly.
The Air Quality Meter detects CO values in the range from 0 ... 500 ppm with a fine resolution of 1 ppm. It also measures the relative humidity in the range from 20 ... 85% (also with 1% resolution) and the temperature from -10 ... 50°C / 14 ... 122°F. If required, the temperature display can also be switched to Fahrenheit. All measured values are shown on a 2 inch LCD display.
In the event of increased CO values, the detector emits both visual and acoustic warning signals. An integrated traffic light function clearly displays the air quality: Green stands for 0 ... 100 ppm, orange for 101 ... 200 ppm and red for 201 ... 500 ppm. If the value exceeds 100 ppm, an additional acoustic warning signal sounds to indicate a potential health hazard.
Equipped with an integrated rechargeable lithium battery that can be conveniently charged via USB-C, the detector is particularly flexible to use. An integrated rubber strap makes it easy to transport and allows the device to be carried or hung up conveniently. With its compact dimensions of 70 x 70 x 28 mm / 2.8 x 2.8 x 1.1 in, modern design and easy handling, it is a practical helper in everyday life.
The Air Quality Meter is suitable for both private and professional use - for example in schools, care facilities, offices or industrial environments - wherever safe indoor air quality is crucial.... Read More | The Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, asThe Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, as well as coaxial cables, such as those used in TV, antenna, and surveillance systems.
Testing is carried out using a two-part system consisting of a main unit and a remote unit, which also allows permanently installed cables to be tested reliably. The most important test procedures include continuity testing of the conductors (pins 1–8), wiring testing to check the correct assignment of the wire pairs, and the detection of short circuits, wiring faults, and split-pair faults. In addition, the shielding of shielded cables is checked. The test range covers cable lengths of up to 305 m, whilst the minimum cable length for split-pair detection is approximately 0.5 m.
Our Cable Detector operates using test signals transmitted between the main unit and the remote unit. The results are displayed via LED indicators. Steady LEDs indicate correct wiring, whilst flashing LEDs indicate faults in the respective wire pairs. Additional status LEDs indicate the type of fault, such as short circuit, miswiring, reversal, or split pair.
The Cable Detector is used in network technology, building cabling, and in IT and communications installations, and is designed for electricians, network technicians, and service technicians to quickly test cable runs.... Read More | Replacement soldering tips for the PCE-ESI 100 (set of 3)
Chisel tip (flat, bevelled – for larger solder joints)
Tapered tip / pointed tip (tapering to a point – for precision work)
Flat tip (wider, straight-cut) | The portable Health & Safety - Surface Resistance Meter on the principle of a two-point pin probe and enables simple and reliable measurement of the surface resistivity of materials - without the need for a megohmmeter, electrometer or other high-voltage measuring devices.
Thanks to its slim and The portable Health & Safety - Surface Resistance Meter on the principle of a two-point pin probe and enables simple and reliable measurement of the surface resistivity of materials - without the need for a megohmmeter, electrometer or other high-voltage measuring devices.
Thanks to its slim and handy design, the device can be conveniently operated with one hand and is ideal for on-site testing or mobile use in production and laboratories. Despite its compact size, it delivers precise results for quickly assessing whether a material is insulating, dissipative or conductive.
The Health & Safety - Surface Resistance Meter uses gold-plated, spring-loaded electrodes that ensure excellent contact with a wide variety of surfaces and minimize contact resistance. All electrodes are replaceable ATE quality pogo pin probes, made from beryllium copper with a hard gold plating of at least 60 microinches - robust, durable and precise.
The two-point probe head is directly connected to an integrated surface resistance measuring device, which measures the surface resistance at a test voltage of approx. 9 volts. The measurement results are shown on a colored LED display. This allows the ESD properties of a material to be clearly recognized at a glance.
With its combination of precise technology, easy handling, compact design and clear LED display, this Health & Safety is the perfect solution for quick on-site testing, quality control and ESD compliance tests in production, laboratories and development.... Read More |