| Description | Gas Detector / Gas Detection Instrument / Detects natural gas & LPG / Heat and gas sensor / WLAN / Voice announcement / Control via app / Real-time alarm / Easy installation
A Gas Detector / Gas Detection Instrument is an important safety device. It recognizes dangerous gas concentrations in the Gas Detector / Gas Detection Instrument / Detects natural gas & LPG / Heat and gas sensor / WLAN / Voice announcement / Control via app / Real-time alarm / Easy installation
A Gas Detector / Gas Detection Instrument is an important safety device. It recognizes dangerous gas concentrations in the air and sounds the alarm in good time to prevent accidents such as explosions or poisoning. Our Gas Detector / Gas Detection Instrument has been specially developed for use in homes, offices and similar indoor areas. It detects both natural gas (methane) and liquefied petroleum gas (LPG, consisting of propane and butane) and reacts as soon as a certain concentration is exceeded.
Our Gas Detector / Gas Detection Instrument measures gas concentrations in the range of 0 ... 100% of the lower explosion limit (LEL), whereby the alarm is triggered at 6% LEL. The response time is a maximum of 30 seconds and the alarm is triggered at a volume of over 70 decibels. A heat sensor is also integrated, which also triggers an alarm at an ambient temperature of 57°C / 134.6°F.
The detector is equipped with a color LCD display that shows the date and time as well as the gas values, the temperature and the remaining sensor life. A Wi-Fi connection is used to connect to the "Smart Life" app, which can be used to monitor the status of the device worldwide. In the event of an alarm, an acoustic and visual warning, a voice message and a push notification are sent to the smartphone. In addition, a connected valve can be activated automatically to stop the gas supply. The sensor has a service life of five years and the device requires a warm-up time of 180 seconds after switching on. The detector is supplied with 5V/1 A power via micro USB and consumes less than 200 mA.
The installation of the Gas Detector / Gas Detection Instrument depends on the type of gas used: for natural gas, which is lighter than air, the device is installed about 30 cm below the ceiling, for LPG, which is heavier than air, about 30 cm above the floor. The distance to the gas source should be 1.5 to 4 meters / 5 to 13 ft. The Gas Detector / Gas Detection Instrument can be attached either with screws or double-sided adhesive tape. Regular tests, which can also be carried out via the app or manually on the device, ensure that it is working properly.
Overall, the Gas Detector / Gas Detection Instrument offers a modern and reliable solution for the early detection of gas leaks and thus makes a significant contribution to increasing safety in rooms supplied with gas. This model of Gas Detector / Gas Detection Instrument combines modern technology with simple operation and is ideal for private and commercial applications.... Read More | The CO2 measuring device PCE-CMM 10 is a multi-function measuring device for measuring the air quality. This CO2 meter measures synchronously the CO2 concentration, the air temperature and the humidity. In addition, the CO2 meter has permanently programmed alarm limits. As soon as the currently The CO2 measuring device PCE-CMM 10 is a multi-function measuring device for measuring the air quality. This CO2 meter measures synchronously the CO2 concentration, the air temperature and the humidity. In addition, the CO2 meter has permanently programmed alarm limits. As soon as the currently measured CO2 measured value exceeds the alarm limit, the alarm is activated. The user is alerted to the CO2 meter by an audible and visual signal.
Using the built-in USB interface, you can continuously charge the CO2 meter to your PC workstation, for example. Thanks to the small blue shape, you can optimally position the CO2 meter at your workplace. Due to the 3 inch display and the strong backlight, you can read the measured values ??optimally.... Read More | Safeguarding sensitive electronic components in manufacturing and handling environments requires precise measurement technology. The Electrical Tester is the indispensable, portable instrument for quickly and reliably checking the surface resistance of materials in ESD-controlled areas.
The Safeguarding sensitive electronic components in manufacturing and handling environments requires precise measurement technology. The Electrical Tester is the indispensable, portable instrument for quickly and reliably checking the surface resistance of materials in ESD-controlled areas.
The Electrical Tester is battery-operated and has integrated parallel electrodes that enable direct testing of the material surface resistance. Thanks to the automatic test voltage selector, the surface resistance tester guarantees maximum measurement accuracy across all relevant ranges. The test voltage automatically switches from 10 V to 100 V as soon as the measured resistance exceeds the value of 1 × 10? ohms.
Two banana sockets allow the connection of external electrodes weighing around 2.25 kg. With these additional components, the Electrical Tester is able to perform professional compliance measurements, such as resistance point-to-point (RTT) or resistance to ground (RTG). The measurement data obtained with this Electrical Tester is essential to ensure adherence to a compliance verification plan (ANSI/ESD S20.20-2007).
The Electrical Tester is ideal for use in electronics production, for testing ESD work mats, workbenches and floor coverings or even in laboratory environments and for quality assurance.... Read More | The Environmental Meter offers a reliable and precise solution for measuring liquid levels in a wide variety of applications. With a measuring range of 0 to 8 m / 0 … 26.2 ft H?O, the level gauge is ideally suited for use in deep wells, rivers, lakes, canals, reservoirs, and coastal monitoringThe Environmental Meter offers a reliable and precise solution for measuring liquid levels in a wide variety of applications. With a measuring range of 0 to 8 m / 0 … 26.2 ft H?O, the level gauge is ideally suited for use in deep wells, rivers, lakes, canals, reservoirs, and coastal monitoring applications up to a water depth of 8 m / 26.2 ft. The high accuracy of ±0.5% FS ensures precise measurement results even under demanding conditions. Thanks to its robust design with a stainless steel housing and durable cable material, the Environmental Meter is resistant to abrasion, oil, acids, and alkalis.
The flexible submersible installation allows for use in both static and flowing media. The long-term stability of ±0.2% FS per year ensures consistently reliable measurement results. The display is operated with a supply voltage of 24 V DC and is designed for connection to sensors with a 4–20 mA output signal. It also features a 4–20 mA analogue output, which enables easy processing of the measured values in higher-level control systems.
Four alarm relays (ALL, AL, AH, AHH) are available for monitoring limit values, allowing individual switching points to be set for different liquid levels. All settings can be conveniently adjusted directly via the control buttons on the display, ensuring quick and easy commissioning. The Environmental Meter is ideally suited for applications in water management, wastewater treatment, irrigation, water diversion, and industrial liquid monitoring.... Read More | The Material Tester is a high-quality measuring instrument designed for calibrating torque sensors and for the precise measurement of the tightening torque of screws and other fasteners. The Material Tester offers a high accuracy of ±1% within the range of 10% ... 100% of the scale and can be The Material Tester is a high-quality measuring instrument designed for calibrating torque sensors and for the precise measurement of the tightening torque of screws and other fasteners. The Material Tester offers a high accuracy of ±1% within the range of 10% ... 100% of the scale and can be operated in both clockwise and anti-clockwise directions.
The Material Tester supports several operating modes such as Peak Hold, MAX, and real-time measurement. In Peak Hold mode, the maximum value is automatically saved, and the measurement data can be transferred via USB to the software, which also enables a pass/fail evaluation. Tolerance ranges can be set directly on the device, allowing values to be checked quickly. An integrated LED traffic light display shows the measured value at a glance.
The choice between the units Newton meter (N·m), kilogram-force-centimeter (kgf·cm), and pound-force-inch (lbf·in) enables flexible applications across various industries. With a storage capacity of 2,000 measurement groups and the option of data transfer via USB, the measuring instrument is ideal for use in the mechanical engineering industry and in scientific research facilities.
The Material Tester operates reliably at ambient temperatures of 5 to 40°C / 41 … 104°F and is powered by a 7.2V NiMH battery, which is optimized for mobile use.
... Read More |