| Description | Gas Detector / Gas Detection Instrument / Detects natural gas & LPG / Heat and gas sensor / WLAN / Voice announcement / Control via app / Real-time alarm / Easy installation
A Gas Detector / Gas Detection Instrument is an important safety device. It recognizes dangerous gas concentrations in the Gas Detector / Gas Detection Instrument / Detects natural gas & LPG / Heat and gas sensor / WLAN / Voice announcement / Control via app / Real-time alarm / Easy installation
A Gas Detector / Gas Detection Instrument is an important safety device. It recognizes dangerous gas concentrations in the air and sounds the alarm in good time to prevent accidents such as explosions or poisoning. Our Gas Detector / Gas Detection Instrument has been specially developed for use in homes, offices and similar indoor areas. It detects both natural gas (methane) and liquefied petroleum gas (LPG, consisting of propane and butane) and reacts as soon as a certain concentration is exceeded.
Our Gas Detector / Gas Detection Instrument measures gas concentrations in the range of 0 ... 100% of the lower explosion limit (LEL), whereby the alarm is triggered at 6% LEL. The response time is a maximum of 30 seconds and the alarm is triggered at a volume of over 70 decibels. A heat sensor is also integrated, which also triggers an alarm at an ambient temperature of 57°C / 134.6°F.
The detector is equipped with a color LCD display that shows the date and time as well as the gas values, the temperature and the remaining sensor life. A Wi-Fi connection is used to connect to the "Smart Life" app, which can be used to monitor the status of the device worldwide. In the event of an alarm, an acoustic and visual warning, a voice message and a push notification are sent to the smartphone. In addition, a connected valve can be activated automatically to stop the gas supply. The sensor has a service life of five years and the device requires a warm-up time of 180 seconds after switching on. The detector is supplied with 5V/1 A power via micro USB and consumes less than 200 mA.
The installation of the Gas Detector / Gas Detection Instrument depends on the type of gas used: for natural gas, which is lighter than air, the device is installed about 30 cm below the ceiling, for LPG, which is heavier than air, about 30 cm above the floor. The distance to the gas source should be 1.5 to 4 meters / 5 to 13 ft. The Gas Detector / Gas Detection Instrument can be attached either with screws or double-sided adhesive tape. Regular tests, which can also be carried out via the app or manually on the device, ensure that it is working properly.
Overall, the Gas Detector / Gas Detection Instrument offers a modern and reliable solution for the early detection of gas leaks and thus makes a significant contribution to increasing safety in rooms supplied with gas. This model of Gas Detector / Gas Detection Instrument combines modern technology with simple operation and is ideal for private and commercial applications.... Read More | The Condition Monitoring is certified in accordance with IEC 61672-1:2013, Class 1 and is ideally suited for professional use in noise monitoring. With a wide frequency range from 10 Hz to 20 kHz and extensive filter options, the device enables precise measurements in almost all areas of applicationThe Condition Monitoring is certified in accordance with IEC 61672-1:2013, Class 1 and is ideally suited for professional use in noise monitoring. With a wide frequency range from 10 Hz to 20 kHz and extensive filter options, the device enables precise measurements in almost all areas of application. The frequency weightings A, C and Z as well as the time weightings S (Slow), F (Fast) and I (Impulse) are supported in order to always ensure application-appropriate measurement behaviour.
The Condition Monitoring also impresses with its comprehensive connectivity: Ethernet, WiFi and USB Type-C enable flexible and uncomplicated data transfer. The internal 8 GB memory and optional SD cards with up to 64 GB provide sufficient storage capacity for extensive measurement campaigns. The high-resolution 4-inch TFT touch display ensures intuitive and convenient operation. Measured variables such as Lp, Lmax, Lmin, Leq, Lpeak, LN(1-99) and numerous other useful functions are displayed clearly and in detail, enabling professional detailed evaluation of the measurement results with this Condition Monitoring.
Its wide range of applications makes the Condition Monitoring the ideal solution for environmental noise monitoring, traffic noise analysis, noise exposure assessment, occupational health and safety monitoring and airport noise monitoring.
The software included in the scope of delivery extends the functionality considerably: it enables live data reception via Ethernet or WiFi, access to stored measurement data and the export of results as a PDF report or CSV file. In addition, the display of the measurement parameters can be freely configured within the software, allowing customisation to specific analysis requirements.... Read More | Safeguarding sensitive electronic components in manufacturing and handling environments requires precise measurement technology. The Electrical Tester is the indispensable, portable instrument for quickly and reliably checking the surface resistance of materials in ESD-controlled areas.
The Safeguarding sensitive electronic components in manufacturing and handling environments requires precise measurement technology. The Electrical Tester is the indispensable, portable instrument for quickly and reliably checking the surface resistance of materials in ESD-controlled areas.
The Electrical Tester is battery-operated and has integrated parallel electrodes that enable direct testing of the material surface resistance. Thanks to the automatic test voltage selector, the surface resistance tester guarantees maximum measurement accuracy across all relevant ranges. The test voltage automatically switches from 10 V to 100 V as soon as the measured resistance exceeds the value of 1 × 10? ohms.
Two banana sockets allow the connection of external electrodes weighing around 2.25 kg. With these additional components, the Electrical Tester is able to perform professional compliance measurements, such as resistance point-to-point (RTT) or resistance to ground (RTG). The measurement data obtained with this Electrical Tester is essential to ensure adherence to a compliance verification plan (ANSI/ESD S20.20-2007).
The Electrical Tester is ideal for use in electronics production, for testing ESD work mats, workbenches and floor coverings or even in laboratory environments and for quality assurance.... Read More | The Voltmeter is a practical and versatile meter that can be used in many areas such as electronics, electrical engineering and DIY. The Voltmeter enables the measurement of DC and AC voltage, resistance, capacitance, frequency and temperature. With True RMS technology, it can also accurately The Voltmeter is a practical and versatile meter that can be used in many areas such as electronics, electrical engineering and DIY. The Voltmeter enables the measurement of DC and AC voltage, resistance, capacitance, frequency and temperature. With True RMS technology, it can also accurately measure complex AC voltages.
The live test function indicates whether a circuit is energised using only a test tip. The NCV (Non-Contact Voltage) function helps to detect live wires without direct contact. The Voltmeter also offers a diode test which can be used to check the functionality of diodes, as well as a continuity test. The multimeter is barely thicker than a smartphone, making it easy to transport and store.
The Voltmeter is powered by a rechargeable lithium battery that boasts a long service life and reliable performance. It has an automatic power-off function after 10 minutes to extend battery life. Thanks to its compact design, the device is easy to transport and can be used in hard-to-reach areas. The 3.3-inch LC display ensures clear and easy-to-read values, while the integrated torch is useful in dark environments.... Read More | The Voltmeter is a versatile meter that is used in various areas of electrical engineering and electronics. The Voltmeter enables precise measurements of voltage, current and resistance and supports both direct and alternating parameters. It also offers practical functions such as checking The Voltmeter is a versatile meter that is used in various areas of electrical engineering and electronics. The Voltmeter enables precise measurements of voltage, current and resistance and supports both direct and alternating parameters. It also offers practical functions such as checking electrical connections using continuity testing and testing diodes for functionality.
For specialised applications, the device offers additional functions such as capacitance and frequency measurement, temperature monitoring and non-contact voltage detection (NCV), which enables electrical fields and live wires to be reliably detected. The Voltmeter is equipped with overload protection, which prevents damage, particularly during high-current measurements, thanks to an integrated fuse. The meter is charged via a modern USB-C interface and it complies with the CAT III 1000 V and CAT IV 600 V safety standards, which ensures safe use even in demanding environments.
The device has three operating modes that can be easily switched via the menu. These modes are suitable for immediate measurements as well as for monitoring and recording maximum and minimum values with curve progression. The internal ring buffer for 8 measured values cannot be output via the interface. After setting threshold values, the multimeter can issue an alarm. The Voltmeter is therefore a reliable companion for professional users and hobby electronics engineers alike who require precise and versatile measurements.... Read More |