| Description | Gas Detector / Gas Detection Instrument / Detects natural gas & LPG / Heat and gas sensor / WLAN / Voice announcement / Control via app / Real-time alarm / Easy installation
A Gas Detector / Gas Detection Instrument is an important safety device. It recognizes dangerous gas concentrations in the Gas Detector / Gas Detection Instrument / Detects natural gas & LPG / Heat and gas sensor / WLAN / Voice announcement / Control via app / Real-time alarm / Easy installation
A Gas Detector / Gas Detection Instrument is an important safety device. It recognizes dangerous gas concentrations in the air and sounds the alarm in good time to prevent accidents such as explosions or poisoning. Our Gas Detector / Gas Detection Instrument has been specially developed for use in homes, offices and similar indoor areas. It detects both natural gas (methane) and liquefied petroleum gas (LPG, consisting of propane and butane) and reacts as soon as a certain concentration is exceeded.
Our Gas Detector / Gas Detection Instrument measures gas concentrations in the range of 0 ... 100% of the lower explosion limit (LEL), whereby the alarm is triggered at 6% LEL. The response time is a maximum of 30 seconds and the alarm is triggered at a volume of over 70 decibels. A heat sensor is also integrated, which also triggers an alarm at an ambient temperature of 57°C / 134.6°F.
The detector is equipped with a color LCD display that shows the date and time as well as the gas values, the temperature and the remaining sensor life. A Wi-Fi connection is used to connect to the "Smart Life" app, which can be used to monitor the status of the device worldwide. In the event of an alarm, an acoustic and visual warning, a voice message and a push notification are sent to the smartphone. In addition, a connected valve can be activated automatically to stop the gas supply. The sensor has a service life of five years and the device requires a warm-up time of 180 seconds after switching on. The detector is supplied with 5V/1 A power via micro USB and consumes less than 200 mA.
The installation of the Gas Detector / Gas Detection Instrument depends on the type of gas used: for natural gas, which is lighter than air, the device is installed about 30 cm below the ceiling, for LPG, which is heavier than air, about 30 cm above the floor. The distance to the gas source should be 1.5 to 4 meters / 5 to 13 ft. The Gas Detector / Gas Detection Instrument can be attached either with screws or double-sided adhesive tape. Regular tests, which can also be carried out via the app or manually on the device, ensure that it is working properly.
Overall, the Gas Detector / Gas Detection Instrument offers a modern and reliable solution for the early detection of gas leaks and thus makes a significant contribution to increasing safety in rooms supplied with gas. This model of Gas Detector / Gas Detection Instrument combines modern technology with simple operation and is ideal for private and commercial applications.... Read More | The Cable Detector is a versatile, reliable and precise measuring device for determining cable lengths using the proven transit time method. With this professional Cable Detector, cables can be reliably measured without having to unwind them - ideal for use in trade, electrical installation and The Cable Detector is a versatile, reliable and precise measuring device for determining cable lengths using the proven transit time method. With this professional Cable Detector, cables can be reliably measured without having to unwind them - ideal for use in trade, electrical installation and maintenance. The measuring range extends from 5 to 1500 (16.4 ... 4,921.3 ft) meters, and the device reliably detects short circuits and breaks in the cable.
Thanks to the integrated cable database with 86 different cable types and the option to teach in your own cables and set customized shortening factors, the Cable Detector is particularly flexible to use. Connection is convenient via 4 mm laboratory sockets with the crocodile clips supplied or via a BNC socket for coaxial cables. Cable cross-sections from 0.25 mm² to 16 mm² are supported, making the Cable Detector suitable for a wide range of applications.
A 2.8 inch display provides a clear presentation of all measurement results, while the multilingual menu enables simple and user-friendly operation. The measurement results can be stored internally and called up again on the device. With a battery life of up to 20 hours and compact dimensions, the Cable Detector is optimized for mobile use and is ideal for daily use on construction sites or in workshops.
The Cable Detector is therefore the perfect solution for anyone looking for a reliable, precise and handy measuring device for determining the length of electrical cables and diagnosing faults.... Read More | The Material Tester is a compact, portable precision tool for applications where exact torque values are crucial. It has an easy-to-read backlit display that provides clear values even in poor lighting conditions.
To assist the user, the Material Tester emits both an acoustic signal and an LED The Material Tester is a compact, portable precision tool for applications where exact torque values are crucial. It has an easy-to-read backlit display that provides clear values even in poor lighting conditions.
To assist the user, the Material Tester emits both an acoustic signal and an LED display as soon as the preset torque value is reached. Four different units of measurement (Nm, kgf-cm, lbf-ft, lbf-in) and three measuring modes - real time, peak value and preset - make it flexible to use. Automatic switch-off after a few minutes saves the batteries, and up to 999 measured values can be stored in the internal memory. The stored values can only be called up on the device.
The Material Tester is equipped with a fine-toothed ratchet head, which enables precise work even with a small radius of movement. Thanks to its robust construction made of metal and resistant plastic, it is durable and suitable for regular use. Our Material Testers are primarily used in vehicle construction, mechanical engineering, bicycle assembly and in the electrical and electronics industry. They are used to tighten bolts and nuts to a precisely defined torque in order to connect components securely and function properly without damaging them. The Material Tester is supplied in a plastic case with 2 AAA batteries.... Read More | The Material Tester is a compact, portable precision tool for applications where exact torque values are crucial. It has an easy-to-read backlit display that provides clear values even in poor lighting conditions.
To assist the user, the Material Tester emits both an acoustic signal and an LED The Material Tester is a compact, portable precision tool for applications where exact torque values are crucial. It has an easy-to-read backlit display that provides clear values even in poor lighting conditions.
To assist the user, the Material Tester emits both an acoustic signal and an LED display as soon as the preset torque value is reached. Four different units of measurement (Nm, kgf-cm, lbf-ft, lbf-in) and three measuring modes - real time, peak value and preset - make it flexible to use. Automatic switch-off after a few minutes saves the batteries, and up to 999 measured values can be stored in the internal memory. The stored values can only be called up on the device.
The Material Tester is equipped with a fine-toothed ratchet head, which enables precise work even with a small radius of movement. Thanks to its robust construction made of metal and resistant plastic, it is durable and suitable for regular use. Our Material Testers are primarily used in vehicle construction, mechanical engineering, bicycle assembly and in the electrical and electronics industry. They are used to tighten bolts and nuts to a precisely defined torque in order to connect components securely and function properly without damaging them. The Material Tester is supplied in a plastic case with 2 AAA batteries.... Read More | A Thermometer is an indispensable safety device for detecting dangerous carbon monoxide concentrations indoors. It is used wherever CO can occur - for example in homes with gas boilers or fireplaces, in workshops with running engines and in boats, motorhomes or other enclosed spaces with combustion A Thermometer is an indispensable safety device for detecting dangerous carbon monoxide concentrations indoors. It is used wherever CO can occur - for example in homes with gas boilers or fireplaces, in workshops with running engines and in boats, motorhomes or other enclosed spaces with combustion appliances.
The Thermometer records CO values in the range from 0 ... 500 ppm with a high resolution of 1 ppm. The Thermometer also measures relative humidity and temperature, whereby the temperature display can also be switched to Fahrenheit. All measured values are shown on an easy-to-read 2-inch LC display with backlighting.
For even more convenience, the Thermometer has a standby mode that can be activated manually. If no input is made within 60 seconds, the display switches off automatically - but the device remains active. In the event of increased CO values, the Thermometer warns with a visual and acoustic alarm. This is supported by a traffic light function: green for 0 ... 100 ppm, orange for 101 ... 200 ppm and red for 201 ... 500 ppm. As soon as the limit value of 100 ppm is exceeded, an additional acoustic warning signal sounds to indicate a possible hazard. Thanks to the integrated lithium battery, which is conveniently charged via USB-C, the detector is particularly flexible to use.... Read More |