| Description | The Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, asThe Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, as well as coaxial cables, such as those used in TV, antenna, and surveillance systems.
Testing is carried out using a two-part system consisting of a main unit and a remote unit, which also allows permanently installed cables to be tested reliably. The most important test procedures include continuity testing of the conductors (pins 1–8), wiring testing to check the correct assignment of the wire pairs, and the detection of short circuits, wiring faults, and split-pair faults. In addition, the shielding of shielded cables is checked. The test range covers cable lengths of up to 305 m, whilst the minimum cable length for split-pair detection is approximately 0.5 m.
Our Cable Detector operates using test signals transmitted between the main unit and the remote unit. The results are displayed via LED indicators. Steady LEDs indicate correct wiring, whilst flashing LEDs indicate faults in the respective wire pairs. Additional status LEDs indicate the type of fault, such as short circuit, miswiring, reversal, or split pair.
The Cable Detector is used in network technology, building cabling, and in IT and communications installations, and is designed for electricians, network technicians, and service technicians to quickly test cable runs.... Read More | 3-Axis Vibration Meter / Vibration Tester for machines and systems / RS232C interface / AC output for headphones / 3-axis piezoelectric acceleration sensor / Incl. sensor tips
The 3-Axis Vibration Meter / Vibration Tester enables fast and precise measurement of acceleration, vibration displacement 3-Axis Vibration Meter / Vibration Tester for machines and systems / RS232C interface / AC output for headphones / 3-axis piezoelectric acceleration sensor / Incl. sensor tips
The 3-Axis Vibration Meter / Vibration Tester enables fast and precise measurement of acceleration, vibration displacement and vibration velocity in three directions (X, Y, Z) or for a single axis. It is used in accordance with ISO 2954 for the detection of unbalance, misalignment and mechanical faults in rotating machinery and is ideal for quality control, commissioning and predictive maintenance on site.
With a frequency range of 10 Hz to 10 kHz, it detects a wide range of vibrations, making it versatile for industrial applications. The 3-Axis Vibration Meter / Vibration Tester weighs just 163 g / 0.4 lbs and is easy to read even in difficult conditions thanks to the backlit 2-inch LCD display. In addition, the 3-Axis Vibration Meter / Vibration Tester switches off automatically after 30 minutes of inactivity to save energy.
The 3-Axis Vibration Meter / Vibration Tester has a 3-axis piezoelectric accelerometer with three mounting options: a magnetic sensor and two measuring tips (one conical and one spherical) that can be attached to the sensor. These accessories enable precise and versatile vibration measurements on various machines and surfaces. This makes the device a handy and powerful tool for industrial vibration measurements. It supports various units such as mm/s, inch/s, m/s², g, ft/s², mm and mil and has a measurement function that displays the maximum measured values.... Read More | The Force Gage is used to precisely check the tension of belts in machines and systems, thereby ensuring optimum power transmission. This Force Gage measures the oscillation frequency of the belt and immediately calculates the belt tension, which is displayed directly in newtons. The measuring rangeThe Force Gage is used to precisely check the tension of belts in machines and systems, thereby ensuring optimum power transmission. This Force Gage measures the oscillation frequency of the belt and immediately calculates the belt tension, which is displayed directly in newtons. The measuring range is between 10 and 680 Hz, with an accuracy of ±1 Hz for frequencies below 100 Hz and ±1% for frequencies above 100 Hz, with a total error of less than 5%.
Special features of the device include the flexible gooseneck sensor for hard-to-reach areas and the option to directly enter the belt length, belt mass and belt width (max. 999.9 mm), which makes the calculation of the belt tension particularly precise. The Force Gage can be switched between displaying the oscillation frequency in Hz and the calculated belt tension in N. It is powered by 3 × AA batteries, making it flexible to use.
This Force Gage is primarily used in the maintenance of conveyor systems, mechanical engineering, the automotive industry and wherever belts need to be tensioned precisely to ensure the performance, safety and service life of the equipment.... Read More | Our robust socket square inserts are specially designed for use with impact wrenches and are ideal for demanding bolting applications. The range covers thread sizes from M16 to M48 and offers the right wrench sizes for a wide variety of applications.
These high-quality socket square inserts impress Our robust socket square inserts are specially designed for use with impact wrenches and are ideal for demanding bolting applications. The range covers thread sizes from M16 to M48 and offers the right wrench sizes for a wide variety of applications.
These high-quality socket square inserts impress with their high load-bearing capacity, precise fit, and long service life – perfect for professional use in industry and assembly.... Read More | The Light Sensor is ideal for monitoring light intensities in greenhouses, industrial facilities or smart farming systems, enabling precise control of lighting and energy use. The Light Sensor detects light intensities from 0 to 65,535 lx and delivers the measured values via a digital RS-485 Modbus The Light Sensor is ideal for monitoring light intensities in greenhouses, industrial facilities or smart farming systems, enabling precise control of lighting and energy use. The Light Sensor detects light intensities from 0 to 65,535 lx and delivers the measured values via a digital RS-485 Modbus RTU output. The accuracy is ±7% FS at 25°C / 77°F, the response time is ?1 s, the supply voltage is 10 to 30V DC, and the robust, moisture-protected housing allows for indoor and outdoor use.
The Light Sensor is primarily used by greenhouse operators, environmental researchers, and companies in the smart farming sector, as well as industrial plants that want to reliably monitor light intensities and implement automated controls.... Read More |