| Description | The Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, asThe Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, as well as coaxial cables, such as those used in TV, antenna, and surveillance systems.
Testing is carried out using a two-part system consisting of a main unit and a remote unit, which also allows permanently installed cables to be tested reliably. The most important test procedures include continuity testing of the conductors (pins 1–8), wiring testing to check the correct assignment of the wire pairs, and the detection of short circuits, wiring faults, and split-pair faults. In addition, the shielding of shielded cables is checked. The test range covers cable lengths of up to 305 m, whilst the minimum cable length for split-pair detection is approximately 0.5 m.
Our Cable Detector operates using test signals transmitted between the main unit and the remote unit. The results are displayed via LED indicators. Steady LEDs indicate correct wiring, whilst flashing LEDs indicate faults in the respective wire pairs. Additional status LEDs indicate the type of fault, such as short circuit, miswiring, reversal, or split pair.
The Cable Detector is used in network technology, building cabling, and in IT and communications installations, and is designed for electricians, network technicians, and service technicians to quickly test cable runs.... Read More | The Condition Monitoring is certified in accordance with IEC 61672-1:2013, Class 1 and is ideally suited for professional use in noise monitoring. With a wide frequency range from 10 Hz to 20 kHz and extensive filter options, the device enables precise measurements in almost all areas of applicationThe Condition Monitoring is certified in accordance with IEC 61672-1:2013, Class 1 and is ideally suited for professional use in noise monitoring. With a wide frequency range from 10 Hz to 20 kHz and extensive filter options, the device enables precise measurements in almost all areas of application. The frequency weightings A, C and Z as well as the time weightings S (Slow), F (Fast) and I (Impulse) are supported in order to always ensure application-appropriate measurement behaviour.
The Condition Monitoring also impresses with its comprehensive connectivity: Ethernet, WiFi and USB Type-C enable flexible and uncomplicated data transfer. The internal 8 GB memory and optional SD cards with up to 64 GB provide sufficient storage capacity for extensive measurement campaigns. The high-resolution 4-inch TFT touch display ensures intuitive and convenient operation. Measured variables such as Lp, Lmax, Lmin, Leq, Lpeak, LN(1-99) and numerous other useful functions are displayed clearly and in detail, enabling professional detailed evaluation of the measurement results with this Condition Monitoring.
Its wide range of applications makes the Condition Monitoring the ideal solution for environmental noise monitoring, traffic noise analysis, noise exposure assessment, occupational health and safety monitoring and airport noise monitoring.
The software included in the scope of delivery extends the functionality considerably: it enables live data reception via Ethernet or WiFi, access to stored measurement data and the export of results as a PDF report or CSV file. In addition, the display of the measurement parameters can be freely configured within the software, allowing customisation to specific analysis requirements.... Read More | Our robust socket square inserts are specially designed for use with impact wrenches and are ideal for demanding bolting applications. The range covers thread sizes from M16 to M48 and offers the right wrench sizes for a wide variety of applications.
These high-quality socket square inserts impress Our robust socket square inserts are specially designed for use with impact wrenches and are ideal for demanding bolting applications. The range covers thread sizes from M16 to M48 and offers the right wrench sizes for a wide variety of applications.
These high-quality socket square inserts impress with their high load-bearing capacity, precise fit, and long service life – perfect for professional use in industry and assembly.... Read More | Radiation Detector / measurement of gamma, beta and X-rays / adjustable alarm values / numerical and graphical display / min, max and average values
Our Radiation Detector is mainly used to measure gamma, beta and X-rays and uses a Geiger-Müller counter to measure the intensity of ionising Radiation Detector / measurement of gamma, beta and X-rays / adjustable alarm values / numerical and graphical display / min, max and average values
Our Radiation Detector is mainly used to measure gamma, beta and X-rays and uses a Geiger-Müller counter to measure the intensity of ionising radiation. The measuring range extends from 0 ... 10 mSv/h. The cumulative dose, average and maximum dose are shown on the larg 2.3 inch multifunctional display, while the real-time measurements are also shown graphically.
The device has two alarm modes: the radiation alarm (0 ... 100 µSv/h) and the cumulative radiation alarm (0 ... 100 mSv). Both alarms are equipped with different settings for visual, audible and vibrating warning signals. The energy range of the device is between 48 and 1500 keV. The radiation measuring device is equipped with a micro USB interface and a rechargeable lithium battery.
The Radiation Detector also displays the current battery level so that the user is always informed. The brightness of the display can be adjusted as required so that it is easier to read even in different lighting conditions. The date and time are also shown on the display.
This Radiation Detector is ideal for applications in research, medicine, industry and environmental protection. It can be used in nuclear power stations, hospitals, laboratories, radiation monitoring and emergency scenarios. Furthermore, it is also useful for construction companies that are working with radioactive materials and in environmental monitoring to ensure that radiation exposure remains within safe limits.... Read More | The digital Torque Meter / Torque Tester is a precise and versatile tool for measuring torque in a variety of applications. It offers a measurement range of 0.1 to 0.5 Nm, a high resolution of 0.0001 Nm, and an accuracy of ±2% of the measured value, ensuring precise and reliable results. The The digital Torque Meter / Torque Tester is a precise and versatile tool for measuring torque in a variety of applications. It offers a measurement range of 0.1 to 0.5 Nm, a high resolution of 0.0001 Nm, and an accuracy of ±2% of the measured value, ensuring precise and reliable results. The device features three operating modes to meet different requirements: In real-time mode, current torque values are displayed continuously. Peak value mode records the highest torque value measured during a test to capture maximum loads.
The mode for calculating and storing the peak value also allows the highest measured value over a defined period to be stored and analyzed, facilitating a detailed evaluation of the peak load. In Pre Mode (mode for storing peak values), there are three possible interfaces: HI displays the maximum stored peak value, LO displays the minimum stored peak value, and AVGE displays the average value of all stored peak values.
The device supports multiple units of measurement, including Nm, lbf ft, kgf cm, and lbf in, making it versatile in use. The device operates with a keyless three-jaw chuck, which ensures secure clamping of the test specimen. In peak value mode, the device can store up to 100 torque peaks automatically or manually. The time for automatic storage of peak values can be flexibly set within a range of 0 to 4 seconds.
A micro-USB interface allows for easy data transfer to other devices, while an automatic shut-off function conserves battery life. The Torque Meter / Torque Tester is powered by a lithium-ion battery that is easy to recharge. Thanks to its user-friendly operation, high precision, and compact design, the Torque Meter / Torque Tester is ideally suited for applications in quality control, research and development, as well as in material and load testing.... Read More |